Commit graph

7568 commits

Author SHA1 Message Date
Icenowy Zheng
e267d94011 sunxi: add DTSI file for V3s
As we have now V3s support in board code, the V3s DTSI file should also
be added.

Add also some CCU include headers to satisfy the DTSI file.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-21 09:23:27 +02:00
Icenowy Zheng
c199489f17 sunxi: add basic V3s support
Basic U-Boot support is now present for V3s.

Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.

As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-21 09:23:17 +02:00
Masahiro Yamada
4e7f8de426 ARM: dts: uniphier: sync Device Tree with Linux
- Use - instead of @ for OPP tables
 - Add input-delay properties to Cadence eMMC nodes
 - Restore full license text because code-diff is annoying
 - Fix NAND compatible strings

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20 23:50:02 +09:00
Masahiro Yamada
637548424b ARM: uniphier: show STM (SCP) status on boot and pinmon command
The SCP (System Control Processor) or what we call STM (Stand-by
MPU) is integrated in LD4, Pro4, sLD8, LD6b, LD11, and LD20.
For these SoCs, show the information if STM is enabled.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20 23:49:56 +09:00
Masahiro Yamada
fed9c76641 ARM: uniphier: enable PSCI sysreset for uniphier_v8_defconfig
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31.  Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20 23:49:50 +09:00
Masahiro Yamada
395e2142e4 ARM: uniphier: setup EHCI PHY paramters for LD11
Set the same PHY parameters as the Boot ROM uses.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20 23:49:50 +09:00
Jernej Skrabec
1ae5def6be sunxi: Add clock support for DE2/HDMI/TCON on newer SoCs
This is needed for HDMI, which will be added later.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:37:31 +02:00
Jernej Skrabec
30ca20234e sunxi: video: Convert lcdc to use struct display_timing
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.

It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:34:52 +02:00
Jernej Skrabec
5e023e7eb3 sunxi: video: Split out TCON code
TCON unit has similar layout and functionality also on newer SoCs. This
commit splits out TCON code for easier reuse later.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:34:50 +02:00
Chen-Yu Tsai
10d8bc5a59 sunxi: Add support for Bananapi M2 Ultra
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.

This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Chen-Yu Tsai
0918648d82 sunxi: Add PSCI support for R40
The R40's CPU controls are a combination of sun6i and sun7i.

All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.

Last, the R40 does not have a secure SRAM block.

This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Chen-Yu Tsai
acef236454 sunxi: Fix CPUCFG address for R40
The R40 has the CPUCFG block at the same address as the A20.
Fix it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Chen-Yu Tsai
8201188cf9 sunxi: Use H3/A64 DRAM initialization code for R40
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Chen-Yu Tsai
328ce7fd50 sunxi: Set PLL lock enable bits for R40
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.

This patch enables it for all the PLLs.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Chen-Yu Tsai
6c7ae2bfc9 sunxi: Fix watchdog reset function for R40
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:00 +02:00
Chen-Yu Tsai
409677ec17 sunxi: Enable AXP221s in I2C mode with the R40 SoC
The R40 SoC uses the AXP221s in I2C mode to supply power.

Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:00 +02:00
Chen-Yu Tsai
379febac5a sunxi: Add initial support for R40
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.

The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.

The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:00 +02:00
Tom Rini
3c476d841d Merge git://git.denx.de/u-boot-fsl-qoriq 2017-04-18 11:36:06 -04:00
Simon Glass
e1bc64eec2 rockchip: Print a message when returning to the bootrom
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
2017-04-18 10:29:26 -04:00
xypron.glpk@gmx.de
1ecd2a2f06 arm: omap-common: add missing va_end()
Each call of va_start must be matched by a call of va_end.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-18 10:29:20 -04:00
Masahiro Yamada
573a3811ed sysreset: psci: support system reset in a generic way with PSCI
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.

The arm-smccc is supported on ARMv7 or later.  Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31.  In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:19 -04:00
Masahiro Yamada
c54bcf6805 ARM: adjust arm-smccc code for use in U-Boot
Adjust ARM SMC Calling Convention code for U-Boot:
  - Replace the license block with SPDX
  - Change path to asm-offsets.h
  - Define UNWIND() as no-op
  - Add Kconfig entry
  - Add asm-offsets

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:17 -04:00
Masahiro Yamada
c2da86f39e ARM: import arm-smccc code from Linux 4.11-rc6
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:

[Linux]                           [U-Boot]
arch/arm/kernel/smccc-call.S   -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes*  -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h      -> include/linux/arm-smccc.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:16 -04:00
Yangbo Lu
3d91f46ca8 armv8/fsl-layerscape: fdt: avoid incorrect fixing with CONFIG_SYS_CLK_FREQ
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ashish kumar
85a9a14e4b armv8: fsl-lsch3: Instantiate TZASC configuration in 2 groups
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Santan Kumar
df1a51df3b armv8: ls2080a: Add serdes2 protocol 0x51 support
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Shengzhou Liu
fb806ad61f arm64/ls1046a: Enable ERRATUM_A008850 for ls1046a SoC
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
York Sun
73fb583829 armv7: ls1021a: Drop macro CONFIG_LS102XA
Use CONFIG_ARCH_LS1021A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
York Sun
c1303bfd7e armv8: ls1043a: Drop macro CONFIG_LS1043A
Use CONFIG_ARCH_LS1043A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
York Sun
4a3ab19322 armv8: ls2080a: Drop macro CONFIG_LS2080A
Use CONFIG_ARCH_LS2080A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ruchika Gupta
511fc86d0b arm: ls1046ardb: Add SD secure boot target
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
  U-Boot by SPL to also include the u-boot Secure Boot header size
  as header is appended to u-boot image. So header will also be
  copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
  (128K) where 32K are reserved for use by boot ROM and 6K for the
  header.
- Reduce the size of CAAM driver for SPL Blobification functions
  and descriptors, that are not required at the time of SPL are
  disabled. Further error code conversion to strings is disabled
  for SPL build.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ruchika Gupta
762f92a60e arm: ls1043ardb: Add NAND secure boot target
Add NAND secure boot target for ls1043ardb.

- Change the u-boot size defined by a macro for copying the main
  U-Boot by SPL to also include the u-boot Secure Boot header size as
  header is appended to u-boot image. So header will also be copied
  from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
  from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
  also defined.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ruchika Gupta
70f9661ca9 arm: ls1043ardb: Add SD secure boot target
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
  ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
  U-Boot by SPL to also include the u-boot Secure Boot header size as
  header is appended to u-boot image. So header will also be copied
  from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
  (128K) where 32K are reserved for use by boot ROM and 6K for secure
  boto header.
- Error messages during SPL boot are limited to error code numbers
  instead of strings to reduce the size of SPL image.

Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Vinitha Pillai-B57223
d2a99502ad armv8: SECURE_BOOT: Enable chain of trust on LS1012A platform
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Vinitha Pillai-B57223
b3635f57d9 armv8: SECURE_BOOT: Enable chain of trust on LS1046A platform
Define bootscript and its header addresses for QSPI target. Also
define PPA header address to enable PPA validation.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
2017-04-17 09:03:30 -07:00
Vinitha Pillai-B57223
d1a795ace9 armv8: fsl-layerscape: SECURE BOOT: Add header address of PPA in kconfig
The header address of PPA defined in Kconfig.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Tom Rini
af8ef2ed21 Merge git://git.denx.de/u-boot-rockchip 2017-04-16 22:08:13 -04:00
Tom Rini
51f866e8da Merge git://git.denx.de/u-boot-dm 2017-04-16 22:07:52 -04:00
Philipp Tomsich
7ee16de58b rockchip: rk3399: spl: add UART0 support for SPL
The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).

To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.

As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.

As the RK3399 needs to use its board_debug_uart_init() function, we
have Kconfig enable it by default for RK3399 builds.

With everything set up to define CONFIG_BAUDRATE via defconfig and
with to have the SPL debug UART either on UART0 or UART2, the configs
for the RK3399 EVB are then update (the change for the RK3399-Q7 is
left for later to not cause issues on applying the change).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:18:29 -06:00
eric.gao@rock-chips.com
d3cf9eb2d8 rockchip: pmic: Enable RK808 for rk3399 evb
For using mipi display, we need to enable lcd3v3
which supplied by rk808,so enable rk808 first.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
eric.gao@rock-chips.com
b644354a7c rockchip: i2c: Enable i2c for rk3399
To enable mipi display, we need to enable pmic
rk808 first for lcd3v3 power,which use i2c0 to
communicate with soc. So enable i2c0.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
eric.gao@rock-chips.com
bc8e8fe40b rockchip: rk3399: Add missing sentinel in syscon
when enable PMIC rk808,the system will halt at very
 early stage,log is shown as bellow.

INFO:    plat_rockchip_pmu_init(1211): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9
time 44561b, 0 (<<----Just stop here)

It's caused by the absence of "{ }" in syscon_rk3399.c
,which will lead to memory overflow like below.According
 to Sysmap file ,we can find the function buck_get_value
of rk808 is just follow the compatible struct,the pointer
"of_match" point to "buck_get_value",but it is not a
struct and don't have member of compatible, In this case,
system crash. So,on the face, it looks like that rk808 is
guilty.but he is really innocent.

while (of_match->compatible) { <<----------
    if (!strcmp(of_match->compatible, compat)) {
    *of_idp = of_match;
    return 0;
    }
    of_match++;
}

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
2017-04-15 10:13:17 -06:00
Klaus Goger
a13110a99f rockchip: ARM64: split RK3399-Q7 board off the RK3399-EVB board
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.

It provides the following feature set:
 * up to 4GB DDR3
 * on-module SPI-NOR flash
 * on-module eMMC (with 8-bit interace)
 * SD card (on a baseboad) via edge connector
 * Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
 * HDMI/eDP/MIPI displays
 * 2x MIPI-CSI
 * USB
   - 1x USB 3.0 dual-role (direct connection)
   - 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
 * on-module STM32 Cortex-M0 companion controller, implementing:
   - low-power RTC functionality (ISL1208 emulation)
   - fan controller (AMC6821 emulation)
   - USB<->CAN bridge controller

Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Philipp Tomsich
faf1afc473 rockchip: dts: rk3399-puma: make the DTS dual-licensed
The RK3399-Q7 (Puma) DTS should (of course) be dual-licensed.
This updates the licensing info in the rk3399-puma.dts.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Heiko Stübner
008a610b4c rockchip: rk3188: enable remap function
Most Rockchip socs have the ability to either map the bootrom or a sram
area to the starting address of the cpu by flipping a bit in the GRF.

Newer socs leave this untouched and mapped to the bootrom but the legacy
loaders on rk3188 and before enabled the remap functionality and the
current smp implementation in the Linux kernel also requires it to be
enabled, to bring up secondary cpus.

So to keep smp working in the kernel, mimic the behaviour of the legacy
bootloaders and enable the remap functionality.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Heiko Stübner
6499b1976c rockchip: cosmetic: Move rock board to its correct position
Somehow 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards") moved
the rock board in between some rk3288 board, probably as a result of
rebasing.

So move it back to its original position above all rk3288 boards.

Fixes: 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Philipp Tomsich
35d1b6dc08 rockchip: dts: rk3399-puma: disable 'fifo-mode' in sdmmc
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Philipp Tomsich
504b9f1a5f rockchip: spl: rk3399: disable DDR security regions for SPL
The RK3399 hangs during DMA of the Designware MMC controller, when
performing DMA-based transactions in SPL due to the DDR security settings
left behind by the BootROM (i.e. accesses to the first MB of DRAM are
restricted... however, the DMA is likely to target this first MB, as it
transfers from/to the stack).

System security is not affected, as the final security configuration is
performed by the ATF, which is executed after the SPL stage.

With this fix in place, we can now drop 'fifo-mode' in the DTS for the
RK3399-Q7 (Puma).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Tom Rini
3fea953698 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-04-14 22:05:17 -04:00
Jean-Jacques Hiblot
fd138ca1bd arm: omap: sata: compile out board-level sata code when CONFIG_DM_SCSI is defined
When CONFIG_DM_SCSI is defined, the SATA initialization will be implemented
in the scsi-uclass driver.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-14 19:38:57 -06:00
Mugunthan V N
01a072c6cf arm: omap: sata: move enable sata clocks to enable_basic_clocks()
All the clocks which has to be enabled has to be done in
enable_basic_clocks(), so moving enable sata clock to common
clocks enable function.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-14 19:38:57 -06:00
Tom Rini
c1a16c3ab5 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2017-04-14 09:05:57 -04:00
Tom Rini
af1b7286d8 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2017-04-14 09:05:46 -04:00
Ley Foon Tan
707cd012e2 arm: socfpga: Convert Altera DDR SDRAM driver to use Kconfig
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-04-14 14:06:57 +02:00
Marek Vasut
cc62ac7578 ARM: socfpga: Disable OC on MCVEVK
Disable the OC test on MCVEVK as the old PHY version does not provide
this information. This fixes the USB OTG operation.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14 14:06:53 +02:00
Marek Vasut
a548bc511f ARM: socfpga: Rename MCVEVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14 14:06:44 +02:00
Chee, Tien Fong
4c0f3e7f7b ARM: socfpga: boot0 hook: remove macro from boot0 header file
Commit ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file") miss out cleaning macro in this header file, and this
has broken implementation of a boot header capability in socfpga
SPL. Remove the macro in this file, and recovering it back
to proper functioning.

Fixes: ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file")

Signed-off-by: Chee, Tien Fong <tien.fong.chee@intel.com>
2017-04-14 14:06:42 +02:00
Georges Savoundararadj
45fa6f1dd5 ARM: socfpga: cyclone5-socdk: Enable ports A & C
With the port C enabled, we can read the GPI input state of:
* the DIP switches (USER_DIPSW_HPS[3:0]/HPS_GPI[7:4])
* the push buttons (USER_PB_HPS[3:0]/HPS_GPI[11:8])

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Signed-off by: Sid-Ali Teir <git.syedelec@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Marek Vasut <marex@denx.de>
2017-04-14 14:06:40 +02:00
Stefan Agner
80b9c3bb80 board: toradex: colibri_vf: Add DCU support for Colibri Vybrid
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-04-14 14:03:07 +02:00
Sanchayan Maity
b215fb3f34 Convert CONFIG_FSL_DCU_FB to Kconfig
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-14 13:37:35 +02:00
Carlo Caione
937386204d mmc: meson: add MMC driver for Meson GX (S905)
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring

Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
2017-04-14 15:16:06 +09:00
Heiner Kallweit
a3b02a1d49 arm: dts: update Meson GXBB / Odroid-C2 DT with recent Linux version
As a prerequisite for adding a Meson GX MMC driver update the
Meson GXBB / Odroid-C2 device tree in Uboot with the latest
version from Linux.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
2017-04-14 15:16:06 +09:00
Tom Rini
b7b24a7a3c Merge git://git.denx.de/u-boot-dm
Here with some DM changes as well as the long-standing AT91 DM/DT
conversion patches which I have picked up via dm.
2017-04-13 17:31:06 -04:00
Wenyou Yang
7abd5aabfa ARM: at91: lds: use "_image_binary_end" for DT location
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:52 -06:00
Wenyou Yang
5bede73c6c ARM: spl: atmel: move mem_init() advance in SPL init.
Because the MMC SPL puts the bbs section in the ddr memory, move
calling mem_init() before calling spl_init().

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:51 -06:00
Wenyou Yang
730a7b4710 ARM: spl: atmel: bring in serial device before init
Before setting up the serial communications, bring in the serial
device from the device tree file.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:51 -06:00
Wenyou Yang
c00d7c33ba ARM: at91: spl: specify MMC and NAND boot device
When OF_CONTROL is enabled, MMC boot device should not be detected
automatically, it should be MMC1 fixedly only the status "enabled"
is available.

Add NAND Flash boot device as well.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:51 -06:00
Wenyou Yang
40e1422136 ARM: dts: at91: add dts file for sama5d4ek
Add the device tree file for sama5d4ek board.

The dts file is copied from Linux-4.4, do the following changes.
 - add the "u-boot,dm-pre-reloc" property to determine which nodes
   which are needed by SPL and by the board_init_f stage.
 - fix the compilation warning.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:51 -06:00
Wenyou Yang
2aaa4ce4bd ARM: dts: at91: add dts files for sama5d4 Xplained
Add the device tree files for sama5d4 Xplained board.

The dts files are copied from Linux-4.4, do the following changes.
 - add reg property for pinctrl node.
 - move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
   nodes to its slibling nodes.
 - add the "u-boot,dm-pre-reloc" property to determine which nodes
   which are needed by SPL and by the board_init_f stage.
 - fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:51 -06:00
Wenyou Yang
27ec910e8c ARM: at91: dt: add dts file for sama5d3 Xplained
Add the device tree file for sama5d3 Xplained board.

The dts files are copied from the Linux-4.9, do changes as below.
 - add the "u-boot,dm-pre-reloc" property to determine which nodes
   which are needed by SPL and by the board_init_f stage.
 - fix the compile warning.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:51 -06:00
Wenyou Yang
110fa9797d ARM: at91: dt: add dts files for sama5d3xek board
Add the device tree files for sama5d3xek board.

The dts files are copied from Linux-4.9, do the changes as below.
 - add reg property for the pinctrl node.
 - move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
   slibling nodes.
 - add the "u-boot,dm-pre-reloc" property to determine which nodes
   which are needed by SPL and by the board_init_f stage.
 - fix the compile warning.
 - add spi0 node aliases.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-13 14:44:50 -06:00
Wenyou Yang
9319a756ff pinctrl: at91: add pinctrl driver
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.

Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-13 14:44:50 -06:00
Wenyou Yang
2dc63f7367 gpio: at91_gpio: remove CPU_HAS_PIO3 macro
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.

Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-13 14:44:50 -06:00
Wenyou Yang
8c4e4101d6 ARM: at91: gpio: fix at91_set_gpio_value() define
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
 #define at91_set_gpio_value(x, y)      at91_set_pio_value(x, y)
 #define at91_get_gpio_value(x)         at91_get_pio_value(x)

But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.

Same as at91_get_gpio_value(x) define.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-13 14:44:49 -06:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Simon Glass
3eace37e50 arm: freescale: Rename initdram() to fsl_initdram()
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-12 13:28:32 -04:00
Stefano Babic
b80c0b9934 Rename aes.h to uboot_aes.h
aes.h is a too generic name if this file can
be exported and used by a program.
Rename it to avoid any conflicts with
other files (for example, from openSSL).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2017-04-12 13:28:27 -04:00
Adam Ford
f479cec3b6 imx: i.mx6q: add the initial support for LogicPD i.MX6Q SOM
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash.  The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM.  Items in the dtsi file
are specific to the SOM itself.  Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-04-12 18:59:12 +02:00
Ye Li
2018ef868c imx: mx7ulp: Fix SPLL/APLL clock rate calculation issue
The num/denom is a float value, but in the calculation it is convert
to integer 0, and wrong result.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-04-12 18:45:10 +02:00
Madan Srinivas
2ff5183fba ARM: Keystone2: Build secure images for K2
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:05 -04:00
Madan Srinivas
39dd0f6faa arm: mach-omap2: Add secure image name common to OMAP and keystone
As K2 can directly boot U-Boot, add u-boot_HS_MLO as the secure image
name for secure K2 devices, for all boot modes other than SPI flash.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:05 -04:00
Vitaly Andrianov
c8ab8ccdd2 arm: mach-omap2: Enable Kconfig support for K2 HS devices
Like the OMAP54xx, AM43xx, & AM33xx family SoCs, the keystone family
of SoCs also have high security enabled models. Allow K2E devices to
be built with HS Device Type Support.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:05 -04:00
Vitaly Andrianov
e8d740f536 arm: mach-keystone: Implements FIT post-processing call for keystone SoCs
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.

The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:04 -04:00
Lukasz Majewski
b8c908762c ti: clocks: Fix do_enable_clocks() to accept NULL pointers as input parameters
Up till this commit passing NULL as input parameter was allowed, but not
handled properly.

When one passed NULL to one of this function parameters, the code was
executed causing data abort.

However, what is more interesting, the abort was not caught because of code
execution in HYP mode with masked CPSR A bit ("Imprecise Data Abort mask bit).
The TI's AM57xx SoC switch to HYP mode with A bit masked in lowlevel_init.S
due to SMC call. Such operation (by default) is performed in SoC ROM code.

The problem would pop up when one:
- Switch back to SVC mode after disabling LPAE support
- Somebody enables A bit (by executing cpsie a asm instruction)

and then the previously described exception would be caught.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:32:49 -04:00
Lukasz Majewski
737af81927 ti: wdt: omap5: Define WDT_BASE for omap5+ SoC
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:32:49 -04:00
Lukasz Majewski
d7ebbe9dc4 ti: wdt: common: Make the wdt IP defines common for the TI platform
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:32:48 -04:00
Tom Rini
04735a8fc4 Merge branch 'master' of git://git.denx.de/u-boot-samsung 2017-04-08 10:20:26 -04:00
Tom Rini
089795090a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-04-08 09:28:02 -04:00
Alexandru Gagniuc
0dcf18c69d spl: Kconfig: SPL_MMC_SUPPORT depends on GENERIC_MMC
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:54 -04:00
Vikas Manocha
dc11d83a2e stm32f7: enable instruction & data cache
It also enables commands for cache enable/disable/status.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-04-08 09:26:51 -04:00
Vikas Manocha
bf4d0495d2 armv7m: add instruction & data cache support
This patch adds armv7m instruction & data cache support.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-04-08 09:26:50 -04:00
Philipp Tomsich
4b0d506ed3 ARMv8: add GOT sections to the list of sections copied
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.

One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.

This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.

Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:46 -04:00
Rask Ingemann Lambertsen
58c4020cf0 arm: sunxi: Add Sunchip CX-A99 initial support
The Sunchip CX-A99 is a board used in some media players. It features:

An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver

This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.

It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.

Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Chen-Yu Tsai
ffe47eb72c ARM: dts: sun9i: Add mmc1 pinmux setting
commit 56b0730157f70dc23d6caff9e7ceb8b377b96b9f upstream.

On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Maxime Ripard
6a3a226eb3 sunxi: Sync GR8 DTS and AXP209 with the kernel
Those DT will be part of 4.10, sync them so we can have our own config.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Jelle van der Waa
0e434ee8da sunxi: add NanoPi NEO Air defconfig
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 10:25:02 +05:30
Jaehoon Chung
8b6edb27e0 arm: dts: trats2: add the i2c-gpio nodes
Add the i2c-gpio nodes for fuelgauge and max77693.
There are i2c8 and i2c9.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-04-07 11:27:55 +09:00
Tom Rini
01abae4d04 Remove various unused interrupt related code
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused.  Rather than migrate
some of these options to Kconfig we just remove the code in question.

The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context.  In these cases we rename
and move the value local to the code in question.

Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:42:18 -04:00
Tom Rini
d53ecad92f Merge branch 'master' of git://git.denx.de/u-boot-sunxi
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:40:24 -04:00
Simon Glass
5e924a13e7 Move dram_init_banksize() to a common header
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 16:36:51 -04:00
Simon Glass
76b00aca4f board_f: Drop setup_dram_config() wrapper
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 16:36:51 -04:00
Simon Glass
088454cde2 board_f: Drop return value from initdram()
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:59:20 -04:00
Simon Glass
52c411805c board_f: Drop board_type parameter from initdram()
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:58:44 -04:00
Marek Vasut
2a4058c240 ARM: mx5: Rename M53EVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-05 18:12:20 +02:00
Marek Vasut
fcea480d1d ARM: mxs: Rename M28EVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-05 18:12:04 +02:00
Tom Rini
433647a7ef Merge git://git.denx.de/u-boot-dm 2017-04-05 08:28:33 -04:00
Andre Przywara
e7bd15ea15 sunxi: Add OrangePi PC 2 initial support
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.

Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
997bde6038 sunxi: introduce Allwinner H5 config option
The Allwinner H5 Soc is bascially an H3 with high SRAM and ARMv8 cores.
As the peripherals and the pinmuxing are almost identical, we piggy
back on the shared MACH_SUN8I_H3_H5 config symbol.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
7b82a229e5 sunxi: prepare for sharing MACH_SUN8I_H3 config symbol
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
170817a497 sunxi: DRAM: add Allwinner H5 support
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
ce6912e128 sunxi: provide ARMv8 mem_map for every ARM64 board
Every armv8 board needs the memory map, so change the #ifdef to
ARM64 to avoid enumerating every single board or SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
bc613d85bd sunxi: Kconfig: introduce CONFIG_SUNXI_HIGH_SRAM
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
85db5831ad sunxi: simplify ACTLR.SMP bit set #ifdef
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
4d24e5f175 fsl: ls102x: remove redundant GENERIC_TIMER_CLK
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
e4916e850b ARM: rename CONFIG_TIMER_CLK_FREQ to COUNTER_FREQUENCY
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
1afd0f6f17 sunxi: fix ACTLR.SMP assembly routine
If we take the liberty to use register r0 to perform our bit set, we
should be nice enough to tell the compiler about it.
Add r0 to the clobber list to avoid potential mayhem.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Stefan Roese
1b8220aa2a arm: bootm: Add dm_remove_devices_flags() call to announce_and_cleanup()
This patch adds a call to dm_remove_devices_flags() to
announce_and_cleanup() so that drivers that have one of the removal flags
set (e.g. DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may do some
last-stage cleanup before the OS is started.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:15:10 -06:00
Jernej Skrabec
7da8680b26 rockchip: Add support for MiQi rk3288 board
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Jernej Skrabec
43b5c78d8d rockchip: cosmetic: Sort RK3288 boards
Sort rk3288 boards in alphabetical order.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
aad10a049d dts: rk3399: move rockchip, vbus-gpio properties into board-specific files
The (shared) rk3399.dtsi had defined the 'rockchip,vbus-gpio'
properties for each USB 3.0 controller.

As the GPIO usage will vary (e.g. one of those GPIOs shuts down one of
the regulators on the RK3399-Q7) between boards, we move this from the
shared dtsi into the device tree file for the EVB board which these
GPIO definitions match.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
3c2bbd5886 dts: rk3399-puma: add DTS for RK3399-Q7 (Puma) SoM
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.

These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).

This includes the following changes from the original development:

 * dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
 * dts: rk3399-puma: add gmac for the RK3399-Q7

This change enables the Gigabit Ethernet support on the RK3399-Q7.

 * dts: rk3399-puma: use serial0 for stdout
 * dts: rk3399-puma: prepare the sdmmc node for SPL booting
 * dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash

The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.

The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.

With some minor improvements on integration into our outbound tree
 - explicitly modelled the SPI flash as 'spiflash' under spi0
   [dts: rk3399-puma: explicitly model spi-flash under spi1]
 - renamed the aliases to spi0 and spi1 to allow easier use of
   commands and legacy (SPL) infrastructure... i.e. the controllers
   will be 0 and 1 for 'sf probe', 'sspi', etc.
   [dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]

 * dts: rk3399-puma: include SPI in the spl-boot-order property

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
db4cc9a034 arm64: rockchip: rk3399-puma: add DDR3-1333 timings
For the initial validation of the RK3399-Q7 (Puma), the DDR3 has been
clocked at 666MHz (i.e. DDR3-1333) using the same (safe) settings as
used in Rockchip's MiniLoader.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
d02d11f8ae rockchip: rk3399: spl: make SPL boot-order configurable via /chosen
The RK3399 does not have any boot selection pins and the BootROM probes
the boot interfaces using the following boot-order:
    1. SPI
    2. eMMC (sdhci in DTS)
    3. SD card (sdmmc in DTS)
    4. USB loader
For ease of deployment, the SPL stage should mirror the boot order of
the ROM and use the same probing order (assuming that valid images can
be detected by SPL) unless instructed otherwise.  The boot-order can
then be configured via the 'u-boot,spl-boot-order' property in the
chosen-node of the DTS.

While this approach is easily extensible to other boards, it is only
implemented for the RK3399 for now, as the large SRAM on the RK3399
makes this easy to fit the needed infrastructure into SPL and our
production setup already runs with DM, OF_CONTROL and BLK in SPL.

The new boot-order property is expected to be used in conjunction with
FIT images (and all legacy image formats disabled via Kconfig).

A boot-sequence with probing and fallthroughs from SPI via eMMC to SD
card (i.e. &spiflash, &sdhci, &sdmmc) has been validated on the RK3399-Q7.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
47197682ef rockchip: rk3188: Add Radxa Rock board
The Rock is a RK3188 based single board computer by Radxa.
Currently it still relies on the proprietary DDR init and
cannot use the generic SPL, but at least is able to boot
a linux kernel and system up to a regular login prompt.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix sort order in defconfig, enable CONFIG_SPL_TINY_MEMSET:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Eddie Cai
07352c9600 rockchip: dts: firefly: add usb host power supply node
firefly have a usb host. add dts node to provide power supply

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
ca0ab2736e dts: rk3399: add gmac for the rk3399
This change adds the gmac node (i.e. the GMAC Ethernet controller) as
defined in the Linux DTS.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
1f08aa1c9f net: gmac_rockchip: Add support for the RK3399 GMAC
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.

This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.

Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).

X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
476f7090bf rockchip: pinctrl: rk3399: add GMAC (RGMII only) support
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration.  This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
 * adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
 * adds the required defines (in the GRF support) for configuring the
   GPIOC pins for RGMII
 * configures the RGMII pins (in GPIOC) when requested via pinctrl

X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
f93a51186a rockchip: arm64: rk3399: remove unconditional debug message
An earlier upstream change contained an unconditional debug message
which would show up as a message similar to the following in the
U-Boot startup (after the ATF and before the U-Boot banner):
      time 159f019, 0

This commit removes this message (instead of making if conditional on
being a debug-build), as it doesn't pertain to any initialisation done
in this file.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Jernej Skrabec
cc232a9d07 rockchip: video: Split out HDMI controller code
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.

DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.

EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.

Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
f4f57c58b5 rockchip: rk3188: Setup the armclk in spl
The armclk starts in slow mode (24MHz) on the rk3188, which results in U-Boot
startup taking a lot of time (U-Boot itself, but also the rc4 decoding done
in the bootrom).

With default pmic settings we can always reach a safe frequency of 600MHz
which is also the frequency the proprietary loader left the armclk at,
without needing access to the systems pmic.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
f785357073 rockchip: clk: rk3188: Allow configuration of the armclk
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.

For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
007a43524b rockchip: rk3188: Cleanup some SPL/TPL rename leftovers
In the beginning, we did SPL -> TPL -> U-Boot, but after clarification
of the real ordering swapped SPL and TPL.
It seems some renames were forgotten and may confuse future readers, so
also swap these to reflect the actual ordering.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
78959d4cbf rockchip: rk3188: Decode the actual amount of ram
There was still a static ram value set in the rk3188-board from the
time where we didn't have actual sdram init code.
Now the sdram init leaves the ram information in SYS_REG2 and we can
decode it similarly to the rk3288.

Right now we have two duplicates of that code, which is still ok and
doesn't really count as common code yet, but if we get a third copy
at some point from a newer soc, we should think about moving that to
a more general position.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
3408509f6f rockchip: rk3188: sdram: Set correct sdram base
Right now we're setting the wrong value of 0 as base in the ram_info struct,
which is obviously wrong for the rk3188. So instead set the correct value
we already have in CONFIG_SYS_SDRAM_BASE.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
3c732de9bf rockchip: rk3188: enable TPL_LIBGENERIC for generic memset
Commit c67c8c604b ("board_init.c: Always use memset()") dropped the naive
memset alternative from board_init_f_init_reserve.
So activate CONFIG_TPL_LIBGENERIC for that common memset implementation.
We cannot use the ARCH-specific memset, as that would incur 200bytes of
additional TPL size, space we do not have.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2017-04-04 20:01:57 -06:00
Kever Yang
232cf96222 rockchip: spl: use spl_early_init() instead of spl_init()
Rockchip spl driver needs using spl_early_init().

Fixes: b3d2861e (spl: Remove overwrite of relocated malloc limit)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
3d54eabcaf rockchip: spl: RK3399: use boot0 hook to create space for SPL magic
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.

This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).

A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.

X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-04-04 20:01:57 -06:00
Tom Rini
3b19c1dbe0 Merge git://git.denx.de/u-boot-tegra 2017-04-04 16:01:02 -04:00
Tom Rini
7d67bb1daf Merge git://git.denx.de/u-boot-dm 2017-04-04 09:18:57 -04:00
Tom Rini
f532703665 Merge git://www.denx.de/git/u-boot-marvell
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
2017-04-04 09:17:56 -04:00
Tom Rini
797f165f7a Merge git://git.denx.de/u-boot-fsl-qoriq 2017-04-04 09:17:08 -04:00
Jaehoon Chung
38130651b7 odroid: dts: change the buck8 min-microvolt value
Change the buck8's min-microvolt to 750000.
Whent thor protocol is used, board_usb_init() should be tried to set to
750000. But it was returned -EINVAL, because '750000' too lower than
2850000. (thor command doesn't work fine because of this problem.)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-04-03 11:35:39 +09:00
Jaehoon Chung
57bbc37909 arm: dts: trats: add i2c_fg node for fuelgauge
Trats has the i2c gpio for fuel-gaugge.
This patch s for preparing to use the fuel-gauge.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-04-03 11:35:38 +09:00
Marcel Ziswiler
4119b7098c mmc: tegra: allow disabling external clock loopback
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2017-04-01 15:45:04 -07:00
Marcel Ziswiler
f38f5f4bcf arm: tegra: initial support for apalis tk1
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.

The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.

For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.

The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
  other two ports as host)

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2017-04-01 15:44:36 -07:00
Stefan Roese
d74238aeb6 arm64: mvebu: armada-7040-db.dts: Change eth1 speed from 2.5G to 1G
The default configuration for the COMPHY-0 port should be 1G, as its
used as 1G SGMII connection. This change is necessary to get the
MAC2 port (SGMII) working on this DB.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-03-29 07:44:43 +02:00
Thomas Petazzoni
a6555ebe1b arm64: marvell: dts: add PPv2.2 description to Armada 7K/8K
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-03-29 07:42:25 +02:00
Dirk Eibach
15f0561043 arm: mvebu: Add gdsys ControlCenter-Compact board
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.

It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.

On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-29 07:38:10 +02:00
Stefan Roese
6bbe0924a7 arm: mvebu: AXP: Add possiblity to configure PEX detection pulse width
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.

Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.

Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-29 07:38:10 +02:00