Commit graph

88312 commits

Author SHA1 Message Date
Hugo Villeneuve
fc1b8e1e7e imx8mn-var-som: read and print SoM infos from eeprom on startup
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.

Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.

Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
2023-07-11 14:40:04 +02:00
Rasmus Villemoes
cb4e79b7ba imx8m: soc.c: demote some printfs to debug
Getting

  Found /vpu_g1@38300000 node
  Modify /vpu_g1@38300000:status disabled
  Found /vpu_g2@38310000 node
  Modify /vpu_g2@38310000:status disabled

etc. on the console on every boot is needlessly verbose. Demote the
"Found ..." lines to debug(), which is consistent with other instances
in soc.c.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
72235cd96a config: xea: Enable DM_SERIAL for the XEA - single binary (SB) u-boot
The single binary version of u-boot for XEA board is used to debrick and
factory programming.

The produced u-boot.sb is a single file, which allows having fully
operational u-boot prompt loaded with imx287 ROM.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
de27953c29 config: xea: Enable DM_SERIAL for the XEA (imx287 based) board
The XEA board now supports the DM_SERIAL feature in u-boot.

The SPL is using the SPL_OF_PLATDATA - i.e. NOT SPL_DM_SERIAL to
reduce the overall size of the SPL binary.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
474c086651 arm: Kconfig: Switch XEA (imx287 based) board to use CONFIG_PL01X_SERIAL
The CONFIG_PL011 used by all other ARCH_MX28 based boards is not
supporting DM_SERIAL. Instead, other define - namely CONFIG_PL01X_SERIAL
shall be used by boards supporting DM_SERIAL.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
8134853b93 arm: xea: Call spl_early_init() before DM serial console is enabled in SPL
The in-spl enabled DM serial console requires the board setup to be
able to parse SPL_OF_PLATDATA based serial driver (pl01x) for the
imx28 based XEA board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
191f683ee2 arm: mxs: Prevent serial console init when in very early SPL boot code
When DM_SERIAL is enabled on mxs (i.e. imx28) platform, the console
early initialization must be postponed until the driver model is
correctly setup.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
a217891948 serial: pl01x: Modify pending callback to test if transmit FIFO is empty
Before this change the FR_TXFF (Transmit FIFO full) bit (5 in
HW_UARTDBG_FR) has been used to assess if there is still data pending
to be sent via UART.

This approach is problematic, as it may happen that serial is in the
middle of transmission (so the TX FIFO is NOT full anymore) and this
test returns true infinitely. As a result, for example in _serial_flush()
DM serial function we are locked in endless while().

The fix here is to test explicitly if the TX FIFO is empty.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
875752adc8 serial: pl01x: Prepare the driver to support SPL_OF_PLATDATA
This commit prepares the pl01x serial driver to be used with
SPL_OF_PLATDATA enabled.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
fdef5e1502 serial: pl01x: Change OF_CONTROL to OF_REAL
Before this change, building this driver for SPL with enabled SPL_DM_SERIAL
was problematic, as '-Wunused-const-variable=' warning was visible.

Now, the code is only considered when u-boot proper is build.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
b8ce78a8c9 dts: xea: Disable 'clks' node for xea (imx287)
As imx28 family of SoCs is NOT supporting the Common Clock Framework (CCF)
the 'clks' property shall NOT be enabled by default.

Without this change u-boot proper before relocation tries to bind driver
(which doesn't exists) for this device. As a result, pre-relocation DTB
parsing is finished with error and the board hangs in a very early stage
of u-boot proper boot process.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
01744484cb dts: xea: Remove clocks property from debug UART on XEA
The imx287 SoC doesn't support common clock framework (CCF), so the
'clocks' property is removed to avoid early (i.e. in SPL) errors when
SPL_OF_PLATDATA is used.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
70b4d610f8 dts: xea: Add u-boot specific 'type' property to duart
The DM_SERIAL implicitly requires CONFIG_PL01X_SERIAL, which
allows support for both serial IP block versions (i.e. PL011 and
PL010).

The decision about used IP block is based on the compatible string,
when DM is used.

In the XEA, the OF_PLATDATA is used to allow usage of serial driver in
the SPL (as the size of SPL is crucial). In this case one cannot extract
the type of IP block from .data field (corresponding to compatible) and
it must be explicitly read at probe from dtoc generated, u-boot specific
property.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
9a1efecb2c dts: xea: Enable debug UART support in XEA's SPL (DM_SERIAL)
After enabling DM_SERIAL for XEA board, the same serial shall be used
in the SPL (with SPL_OF_PLATDATA support).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
9c2eefaf0d spl: xea: Provide stub DM driver for imx28 clocks
This code fixes following WARNING:
  DTOC    spl/dts/dt-plat.c
fsl_imx28_clkctrl: WARNING: the driver fsl_imx28_clkctrl was not found in the driver list

As imx28 doesn't yet support common clock framework, this prevents from
DTOC warnings during SPL build.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
11194c0d11 defconfig: xea: Change default spi-nor memory bus to 2
After the re-sync with Linux kernel (v6.0) of the XEA DTS
(SHA1: 7d08ddd09b) the alias
for SPI bus, to which SPI-NOR  memory is connected, has changed from
'spi3' to 'spi2'.

To be in sync with current u-boot's xea dts, the default bus number
(which allows running 'sf probe' without any extra parameters given)
has been adjusted.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
c5e8c336ec dts: xea: Provide missing FEC required properties (mac0 and reg_fec_3v3)
After the commit (SHA1: 7d08ddd09b) some
u-boot specific XEA FEC related properties have been replaced by ones
from the Linux kernel.

To be more specific - XEA board (and imx287 in general) has built L2
switch connected to FEC, which needs some special treatment.

In u-boot it is handled with 'mac0' node, whereas Linux uses dedicated
switch DTS node.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Lukasz Majewski
0d30b6c4ec dts: xea: Delete not used in u-boot DTS nodes
After the re-sync with Linux Kernel's DTS
(SHA1: 7d08ddd09b), the XEA's
descripion has nodes and properties, which are NOT utilized
in the u-boot.

To avoid confusion - those are deleted.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:04 +02:00
Emanuele Ghidoli
611b94bf69 toradex: tdx-cfg-block: add 0070 verdin i.mx 8m plus quad sku
Add new i.MX 8M Plus Quad SKU to ConfigBlock handling.

0070: Verdin iMX8M Plus Quad 8GB WB IT

This SKU is identical to 0066 but supporting Industrial Temperature range.

Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
e7c1c0811b arm: config: Adjust imx287 based XEA board PMU configuration
This patch adjusts XEA's PMU setup as this board is supposed to be
mainly powered from DCDC_BATT source.

Moreover, in this HW design the VDD_4P2 is not used as well.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
301c6e6e69 arm: mxs: Add function to dump PMU registers
This commit provides function, which when debugging
output is enabled dumps the IMX28 PMU registers.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
79230640cb arm: mxs: Provide Kconfig option to not enable 4P2 regulator in IMX28 PMU
The IMX28 PMU (Power Management Unit) has a dedicated Linear Regulator
to produce (by default) 4.2V output - available outside the chip as
VDD_4P2.

When system is supposed to not use VDD5V as a main power source - instead
the DCDC_BATT is used; it is safe to disable this regulator.

As the in-PMU DCDC switching regulator (from which DCDC_VDDA, DCDC_VDDIO
and DCDC_VDDD are generated) can be driven from DCDC_BATT or output
of this 4P2 regulator - by disabling the latter the use of the DCDC_BATT
is forced.

To be more specific - according to NXP's AN4199 the DCDC_BATT source is
preferred (over VDD5V), as more efficient and stable source for
industrial applications.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
249a3cc1af arm: mxs: Provide Kconfig option to disable battery charging at IMX28 PMU
This new Kconfig option allows disabling the in-PMU battery charging
block. This may be required when DCDC_BAT source is powered not from
battery, but from already regulated, good quality source.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Lukasz Majewski
1c3c601ac5 arm: mxs: Provide Kconfig option to to not use VDD5V as IMX28 PMU source
This option sets the current limit for 5V source to zero, so all
the PMU outputs are primarily powered from battery source (DCDC_BAT).

This option may be set on systems, where the 5V is NOT supposed to be
in any scenario powering the system - for example on systems where
DCDC_BAT is connected to fixed and regulated 4.2V source (so the
"battery" is not present).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2023-07-11 14:40:03 +02:00
Fabio Estevam
8f70f3df62 power: imx8m-power-domain: Add delay to align with kernel driver
In the imx8m power domain kernel driver, there is an extra udelay(5)
prior to requesting the domain to power up:

https://github.com/torvalds/linux/blob/v6.3/drivers/soc/imx/gpcv2.c#L347-L375

Haven't observed any issues due to the lack of this delay in U-Boot yet,
but better to align it with the kernel driver implementation.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2023-07-11 14:40:03 +02:00
Tim Harvey
79e315761c board: gateworks: venice: update board doc to show other emmc parts
Update the venice board documentation to show how to install to the
various eMMC hardware partitions available as the same binary firmware
can be placed in either user/boot0/boot1 without build-time config
changes. Note that the boot offsets differ depending on the SoC and the
eMMC hardware partition.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
13897ff6d9 board: gateworks: venice: move env location
To allow U-Boot to fit within emmc boot partitions move the env from
just under 16MiB to just under 4MiB as some emmc devices used on venice
boards have 4MiB boot partitions. This still leaves plenty of room for
U-Boot.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
7b39e5b53a board: gateworks: venice: dynamically update the update_firmware script
The update_firmware script is intended to update the boot firmware but
the details including the offset and hardware partition are dependent
on the boot device.

Specifically:
- IMX8MM/IMX8MP (BOOTROM v2) the offset is 32KiB for SD and eMMC user
  hardware partition and 0KiB for eMMC boot partitions.
- IMX8MM the offset is 33KiB for SD and eMMC regardless of hardware
  partition.

Dynamically set soc, dev, bootpart, and bootblk env vars at runtime
and use these in the update_firmware script. Remove the splblk env var
from config files as its no longer needed.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
2c2cc1eaab board: gateworks: venice: dynamically determine U-Boot env partition
Determine the U-Boot env hardware partition depending on the boot
device.

This allows the same boot firmware image to be placed on user, boot0,
or boot1 without changing CONFIG_SYS_MMC_ENV_PART.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
8236c05ddb board: gateworks: venice: dynamically determine U-Boot raw sector
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to adjust for
IMX8MN and IMX8MP when booting from an eMMC boot partition due
to IMX BOOTROM v2 using an SPL offset of 0 for boot partitions
and 32K for the user partition.

In order to allow the same firmware to run on both user and boot
hardware partitions adjust raw_sect dynamically at runtime.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:03 +02:00
Tim Harvey
c226f84256 board: gateworks: venice: add eraseenv command
Add eraseenv command and remove the unnecessary env command.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2023-07-11 14:40:03 +02:00
Tim Harvey
8849cc7bd9 board: gateworks: venice: add GPIO name lookup
Add GPIO name lookup so that you can act on GPIO's by name vs controller
id:

Before:
u-boot=> gpio input pci_wdis#
GPIO: 'pci_wdis#' not found
Command 'gpio' failed: Error -22

After:
u-boot=> gpio input pci_wdis#
gpio: pin pci_wdis# (gpio 103) value is 1

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2023-07-11 14:40:03 +02:00
Sergio Prado
7a63432e9d configs: verdin-imx8mp: enable ARCH_MISC_INIT
This is required to boot a FIT image, otherwise the caam_jr driver is
not initialized and the hash verification fails with the following
error:

Verifying Hash Integrity ... sha256dev_get_priv: null device
CAAM was not setup properly or it is faulty

Signed-off-by: Sergio Prado <sergio.prado@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2023-07-11 14:40:03 +02:00
Oleksandr Suvorov
d31ffce81d ARM: imx9: support env in fat and ext4
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.

As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.

This solution is based on (with added SPL support):
Link: https://lore.kernel.org/all/20211020191626.3648540-1-ricardo@foundries.io/
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-07-11 14:40:02 +02:00
Giulio Benetti
04e08e3c54 arm: mx6: module_fuse: fix build failure due to wrong argument name
nodeoff variable should be variable off returned by fdt_path_offset() so
let's rename it to off.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2023-07-11 14:40:02 +02:00
Andrejs Cainikovs
ce38c6432b colibri-imx8x: print firmware versions
Print firmware versions during U-Boot start:

 BuildInfo:
  - SCFW f5623878, SECO-FW c9de51c0, IMX-MKIMAGE 0, ATF c6a19b1
  - U-Boot 2022.04-00335-g65192567f81-dirty

Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
2023-07-11 14:40:02 +02:00
Adam Ford
cacf0f8a19 configs: imx: imx8mm_beacon: Add config option for QSPI booting
The imx8mm_beacon SOM has a QSPI part attached to the FSPI controller.
Update the header and spl files to support booting from NOR flash and
add imx8mm_beacon_fspi_defconfig to support this configuration.

Signed-off-by: Adam Ford <aford173@gmail.com>
2023-07-11 14:40:02 +02:00
Adam Ford
5054560e0c imx: imx8mm-beacon: Enable FlexSPI in U-Boot
In order to use the FlexSPI interface in U-Boot, configure
the alias to make spi0 point to flexspi.

With that enabled, sf probe detects the QSPI part as:
SF: Detected n25q256ax1 with page size 256 Bytes, erase size 4 KiB, total 32 MiB

Signed-off-by: Adam Ford <aford173@gmail.com>
2023-07-11 14:40:02 +02:00
Tom Rini
146a82c017 Merge branch 'next' 2023-07-10 14:29:14 -04:00
Tom Rini
05aa6516c6 Prepare v2023.07
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-07-10 14:13:47 -04:00
Tom Rini
76c61f29d6 Merge tag 'fsl-qoriq-2023-7-6' of https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
Enable DM Serial for ls1043ardb and ls1046ardb/afrwy
Fixed secure boot on LS-CH2 platforms
2023-07-09 21:54:40 -04:00
Malte Schmidt
e05a4b12a0 mkeficapsule: fix efi_firmware_management_capsule_header data type
The data type of item_offset_list shall be UINT64 according to the UEFI [1]
specifications.

In include/efi_api.h the correct data type is used. The bug was probably
never noticed because of little endianness.

[1] https://uefi.org/specs/UEFI/2.10/index.html

Signed-off-by: Malte Schmidt <malte.schmidt@weidmueller.com>

Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
2023-07-09 10:32:28 +02:00
Heinrich Schuchardt
fefb7e1e3d doc: harmonize Linux kernel documentation links
Linux internally uses https://www.kernel.org/doc/html/latest/ for
documentation links. When referring to their documentation we should do the
same.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2023-07-09 04:00:06 +02:00
Masahisa Kojima
0c95744bcc cmd: efidebug: add missing efi_free_pool for dh subcommand
This adds the missing efi_free_pool call for dh subcommand.

Fixes: a80146205d ("cmd: efidebug: add dh command")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2023-07-09 03:53:08 +02:00
Alper Nebi Yasak
9fd3f881c6 efi_loader: Increase default variable store size to 64KiB
Debian's arm64 UEFI Secure Boot shim makes the EFI variable store run
out of space while mirroring its MOK database to variables. This can be
observed in QEMU like so:

  $ tools/buildman/buildman -o build/qemu_arm64 --boards=qemu_arm64 -w
  $ cd build/qemu_arm64
  $ curl -L -o debian.iso \
      https://cdimage.debian.org/debian-cd/current/arm64/iso-cd/debian-12.0.0-arm64-netinst.iso
  $ qemu-system-aarch64 \
      -nographic -bios u-boot.bin \
      -machine virt -cpu cortex-a53 -m 1G -smp 2 \
      -drive if=virtio,file=debian.iso,index=0,format=raw,readonly=on,media=cdrom
  [...]
  => # interrupt autoboot
  => env set -e -bs -nv -rt -guid 605dab50-e046-4300-abb6-3dd810dd8b23 SHIM_VERBOSE 1
  => boot
  [...]
  mok.c:296:mirror_one_esl() SetVariable("MokListXRT43", ... varsz=0x4C) = Out of Resources
  mok.c:452:mirror_mok_db() esd:0x7DB92D20 adj:0x30
  Failed to set MokListXRT: Out of Resources
  mok.c:767:mirror_one_mok_variable() mirror_mok_db("MokListXRT",  datasz=17328) returned Out of Resources
  mok.c:812:mirror_one_mok_variable() returning Out of Resources
  Could not create MokListXRT: Out of Resources
  [...]
  Welcome to GRUB!

This would normally be fine as shim would continue to run grubaa64.efi,
but shim's error handling code for this case has a bug [1] that causes a
synchronous abort on at least chromebook_kevin (but apparently not on
QEMU arm64).

Double the default variable store size so the variables fit. There is a
note about this value matching PcdFlashNvStorageVariableSize when
EFI_MM_COMM_TEE is enabled, so keep the old default in that case.

[1] https://github.com/rhboot/shim/pull/577

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2023-07-09 03:53:08 +02:00
Alper Nebi Yasak
d7fe913f23 efi_loader: Avoid underflow when calculating remaining var store size
The efi_var_mem_free() function calculates the available size for a new
EFI variable by subtracting the occupied buffer size and the overhead
for a new variable from the maximum buffer size set in Kconfig. This
is then returned as QueryVariableInfo()'s RemainingVariableStorageSize
output.

This can underflow as the calculation is done in and processed as
unsigned integer types. Check for underflow before doing the subtraction
and return zero if there's no space.

Fixes: f1f990a8c9 ("efi_loader: memory buffer for variables")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2023-07-09 03:53:08 +02:00
Paul Barker
0ef6343439 x86: Update docs link in bootparam header
After Linux commit ff61f0791ce9, x86 documentation was moved to
arch/x86 and the link in bootparam.h was broken.

Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2023-07-09 03:53:08 +02:00
Tom Rini
fa1e124ee7 Merge branch '2023-07-07-assorted-build-improvements' into next
- Correct a few dependencies in Kconfig and better handle some generated
  files so that they are properly cleaned later.
2023-07-08 11:28:39 -04:00
Michal Simek
99a0532a2d sysreset: Change Kconfig GPIO dependency
DM_GPIO depends on GPIO to be enabled but select will cause that DM_GPIO is
selected without GPIO which ends up in compilation error:
undefined reference to `dm_gpio_set_value'
undefined reference to `dm_gpio_get_value'
undefined reference to `dm_gpio_free'
undefined reference to `gpio_request_by_name'

Signed-off-by: Michal Simek <michal.simek@amd.com>
[trini: Fix configs which had relied on these select's]
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-07-07 16:47:15 -04:00
Ying Sun
0f42f89955 tpl: Kconfig: TPL_BANNER_PRINT depends on DEBUG_UART && TPL_SERIAL
As implemented in the arch/arm/mach-rockchip/tpl.c file,
the CONFIG_TPL_BANNER_PRINT option will not work
if either of these options is not enabled.

Add dependency constraints to the CONFIG_TPL_BANNER_PRINT option
definition to prevent configuration problems
where option is enabled but do not take effect.

Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
2023-07-07 16:25:56 -04:00