The timer_init function is called before relocation and writes to bss data
were corrupting relocation data. Fix this by removing the call to
reset_timer_masked. The initial timer count should be 0 or near 0 anyway,
so initializing the variables are not needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The 150MHz clock rate gives u-boot time functions problems and there's no
benefit to a fast clock, so lower the rate.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Various changes to highbank config:
Enable EFI partitions
Enable ext4 and FAT filesystems
Enable bootz command and raw initrd
Increase cmd and print buffer size to 1K
Change serial baudrate to 115200
Enable hush shell
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
There is no reason to wait for the entire frame to start DMA on receive,
so enable rx cut-thru for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
interrupt_init also sets up the abort stack, but is not setup before
relocation. So any aborts during relocation will hang and not print out
any useful information. Fix this by moving the interrupt_init to after
the stack setup in board_init_f.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Make it similar to the code in mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Make it similar to the code in mips64/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The t4 register already holds the cache
line size, and the value of the register
is not changed in mips_init_icache.
Get the cache line size value from t4 for
mips_init_dcache as well and remove the
superfluous assignment of t5 register.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
The MIPS code uses centralized u-boot.lds script already,
and dynamic relocation is supported as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Checking mips32/time.c with checkpatch.pl shows this:
arch/mips/cpu/mips32/time.c:30: WARNING: line over 80 characters
arch/mips/cpu/mips32/time.c:57: ERROR: return is not a function, parentheses are not required
total: 1 errors, 1 warnings, 0 checks, 85 lines checked
Fix the code to make checkpatch.pl happy.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.
The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Move the GT64120 register base to 0x1be00000
and setup PCI BAR registers as done by the
original YAMON bootloader.
This is needed for running Linux kernel.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The MIPS Malta board has a SOFTRES register. Writing a
magic value into that register initiates a board reset.
Use this feature to implement reset support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.
This is enough to boot U-Boot to the command prompt
both in little and big endian mode.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
On the origial Malta boards the REVISION register is
accessible at the 0x1fc00010 address. The contents of
this register gives information about the revision
of the Malta and Core Boards.
This register is used by the Linux kernel to identify
the actual board it is running on. However the register
is not emulated properly by Qemu, so put a hardcoded
value into the flash to make Linux work.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The Linux specific register access macros, the
extern function declarations and the UL suffixes
has been removed.
The header file will be used for the qemu-malta
board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The pcnet driver uses the pci_phys_to_mem function
to get the memory address of the DMA buffers. This
This assumes an 1:1 mapping between the PCI and
physical memory which is not true on all platforms.
On MIPS platform U-Boot is running within a mapped
memory region, and the pci_phys_to_mem macro can't
be used to obtain the memory address of the buffers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
Like many other projects, U-Boot has a tradition of including big
blocks of License headers in all files. This not only blows up the
source code with mostly redundant information, but also makes it very
difficult to generate License Clearing Reports. An additional problem
is that even the same lincenses are referred to by a number of
slightly varying text blocks (full, abbreviated, different
indentation, line wrapping and/or white space, with obsolete address
information, ...) which makes automatic processing a nightmare.
To make this easier, such license headers in the source files will be
replaced with a single line reference to Unique Lincense Identifiers
as defined by the Linux Foundation's SPDX project [1]. For example,
in a source file the full "GPL v2.0 or later" header text will be
replaced by a single line:
SPDX-License-Identifier: GPL-2.0+
We use the SPDX Unique Lincense Identifiers here; these are available
at [2].
Note: From the legal point of view, this patch is supposed to be only
a change to the textual representation of the license information,
but in no way any change to the actual license terms. With this patch
applied, all files will still be licensed under the same terms they
were before.
Note 2: The apparent difference between the old "COPYING" and the new
"Licenses/gpl-2.0.txt" only results from switching to the upstream
version of the license which is differently formatted; there are not
any actual changes to the content.
Note 3: There are some recurring questions about linense issues, such
as:
- Is a "All Rights Reserved" clause a problem in GPL code?
- Are files without any license header a problem?
- Do we need license headers at all?
The following excerpt from an e-mail by Daniel B. Ravicher should help
with these:
| Message-ID: <4ADF8CAA.5030808@softwarefreedom.org>
| Date: Wed, 21 Oct 2009 18:35:22 -0400
| From: "Daniel B. Ravicher" <ravicher@softwarefreedom.org>
| To: Wolfgang Denk <wd@denx.de>
| Subject: Re: GPL and license cleanup questions
|
| Mr. Denk,
|
| Wolfgang Denk wrote:
| > - There are a number of files which do not include any specific
| > license information at all. Is it correct to assume that these files
| > are automatically covered by the "GPL v2 or later" clause as
| > specified by the COPYING file in the top level directory of the
| > U-Boot source tree?
|
| That is a very fact specific analysis and could be different across the
| various files. However, if the contributor could reasonably be expected
| to have known that the project was licensed GPLv2 or later at the time
| she made her contribution, then a reasonably implication is that she
| consented to her contributions being distributed under those terms.
|
| > - Do such files need any clean up, for example should we add GPL
| > headers to them, or is this not needed?
|
| If the project as a whole is licensed under clear terms, you need not
| identify those same terms in each file, although there is no harm in
| doing so.
|
| > - There are other files, which include both a GPL license header
| > _plus_ some copyright note with an "All Rights Reserved" clause. It
| > has been my understanding that this is a conflict, and me must ask
| > the copyright holders to remove such "All Rights Reserved" clauses.
| > But then, some people claim that "All Rights Reserved" is a no-op
| > nowadays. License checking tools (like OSLC) seem to indicate this is
| > a problem, but then we see quite a lot of "All rights reserved" in
| > BSD-licensed files in gcc and glibc. So what is the correct way to
| > deal with such files?
|
| It is not a conflict to grant a license and also reserve all rights, as
| implicit in that language is that you are reserving all "other" rights
| not granted in the license. Thus, a file with "Licensed under GPL, All
| Rights Reserved" would mean that it is licensed under the GPL, but no
| other rights are given to copy, modify or redistribute it.
|
| Warm regards,
| --Dan
|
| Daniel B. Ravicher, Legal Director
| Software Freedom Law Center (SFLC) and Moglen Ravicher LLC
| 1995 Broadway, 17th Fl., New York, NY 10023
| (212) 461-1902 direct (212) 580-0800 main (212) 580-0898 fax
| ravicher@softwarefreedom.org www.softwarefreedom.org
[1] http://spdx.org/
[2] http://spdx.org/licenses/
Signed-off-by: Wolfgang Denk <wd@denx.de>
Setting the direction and an output value should be done by
First, set the desired output value.
Then, switch to output.
If this is done in the inverse order, like at the moment,
there can be a glitch on the GPIO line while switching first
the old output value and aftwards the new one.
Fix this by inverting the order of the direction/set_value
calls.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Pull all the duplicate configuration options into configs/mxs.h
from the board configuration files. This reduces the files greatly
and makes them somewhat more readable. Besides, we do no longer
have such a horrible duplication of code.
Note that the mx23evk grew in size slightly. This is due to the
CONFIG_SYS_CBSIZE now being set to 1024 as it is on the rest of
MXS systems.
This patch also fixes the OCRAM size for i.MX23. The i.MX23 has
only 32kB of OCRAM, while i.MX28 has 128kB of OCRAM.
I verified the configuration didn't change for each of the boards,
but I didn't boot-test it on the boards I do not have. I configured
U-Boot for each board using the "make ... <board>_config" command
and then ran "cpp -I include -dM include/config.h" , which dumped
all the configuration options. I did this both before and after this
patch and finally compared the results for each MXS board. Actually,
the results do differ slightly, since the configs/mxs.h file now
properly includes the correct iomux-mx23.h or iomux-mx28.h , so
while comparing, I had to ignore these new defines. These have no
impact on U-Boot configuration though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The timer3 counter unit for lastdesc and now values are inconsistent in current
code. The unit of "readl(&tmr->timer3_counter) / (CONFIG_SYS_CLK_FREQ / 2)" is
second. However, CONFIG_SYS_HZ is defined as 1000 in board config file.
This means the accuracy of "lastdec" and "now" should be in millisecond,
thus fix the equation to set lastdec and now variables accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Add a header file, setup.h, which copy from Linux source code,
this file contain structures are used to pass initialisation parameters
to Linux. Enable this function on adp-ag101/adp-ag101p target
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
Due to improper external function declaration,
building U-Boot for the adp-ag102 board shows
this warning:
adp-ag102.c: In function 'pci_init_board':
adp-ag102.c:95: warning: function declaration isn't a prototype
Include the 'faraday/ftpci100.h' header which
provides the proper declaration and remove the
local declaration to get rid of the warning.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Even though the header files is used only by the
pci_ftpci100 driver, it contains declaration for
a function which is used by external code.
Move the header file to a common location which
lets external code use it.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
The pci_ftpci_init() function is implemented
in 'drivers/pci/pci_ftpci100.c' however it is
always called by external code.
Add function declaration into ftpci100.h to
make it visible for external code.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Add a const keyword to the sect_buf argument of
ide_write_data to fix the following warning:
cmd_ide.c: In function '__ide_output_data':
cmd_ide.c:548: warning: passing argument 2 of 'ide_write_data' discards qualifiers from pointer target type
/devel/u-boot.git/include/ide.h:76: note: expected 'ulong *' but argument is of type 'const ulong *'
Also modify the driver-model documentation to
match with the new prototype.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
The FTSDC010_DCR_FIFO_RST symbol is conditionally
defined in <faraday/ftsdc010.h> and it is available
available when CONFIG_FTSDC010_SDIO is enabled.
However the actual driver code unconditionally uses
the FTSDC010_DCR_FIFO_RST constant and this causes
build error if CONFIG_FTSDC010_SDIO is not enabled.
The following error happens when compiling for the
adp-ag101 board:
ftsdc010_mci.c: In function 'ftsdc010_request':
ftsdc010_mci.c:178: error: 'FTSDC010_DCR_FIFO_RST' undeclared (first use in this function)
ftsdc010_mci.c:178: error: (Each undeclared identifier is reported only once
ftsdc010_mci.c:178: error: for each function it appears in.)
The patch ensures that the FTSDC010_DCR_FIFO_RST
symbol gets used only if CONFIG_FTSDC010_SDIO is
defined.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Kuo-Jung Su <dantesu@faraday-tech.com>
U-Boot does not compile for the adp-ag101 boards since
commit f6c3b34697 (mmc:
update Faraday FTSDC010 for rw performance)
The driver assumes that the bit manipulation macros
are provided by all architectures. This is not the
case for nds32 and it causes a build error like this:
ftsdc010_mci.c: In function 'ftsdc010_clkset':
ftsdc010_mci.c:118: warning: implicit declaration of function 'setbits_le32'
ftsdc010_mci.c:123: warning: implicit declaration of function 'clrbits_le32'
drivers/mmc/libmmc.o: In function `ftsdc010_request':
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:234: undefined reference to `setbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:243: undefined reference to `clrbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:234: undefined reference to `clrbits_le32'
drivers/mmc/libmmc.o: In function `ftsdc010_clkset':
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:118: undefined reference to `clrbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:118: undefined reference to `clrbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:121: undefined reference to `setbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:123: undefined reference to `setbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:123: undefined reference to `setbits_le32'
The patch adds bit manipulation macros for the
nds32 architecture to avoid the errors. The macros
are copied from the ARM implementation.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
