Commit graph

135 commits

Author SHA1 Message Date
Simon Glass
1169299135 mmc: Add debug() output on read errors
Allow read errors to be diagnosed more easily.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:25 -06:00
Simon Glass
e7ecf7cb5a dm: mmc: Add an MMC uclass
Add basic support for MMC, providing a uclass which can set up an MMC
device. This allows MMC drivers to move to using driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:25 -06:00
Tom Rini
d81572c272 Merge git://git.denx.de/u-boot-mpc85xx 2015-05-05 14:57:23 -04:00
Rob Herring
5a20397b00 mmc: remove the MMC_MODE_HC flag
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-05-05 12:29:36 +03:00
Andrew Gabbasov
bd47c13583 mmc: Fix splitting device initialization
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.

Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:55:46 +03:00
Andrew Gabbasov
1677eef459 mmc: Restructure polling loops to avoid extra delays
The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.

Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:55:00 +03:00
Andrew Gabbasov
cc17c01f2d mmc: Continue polling MMC card for OCR only if it is still not ready
Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:54:40 +03:00
Andrew Gabbasov
5289b5350b mmc: Do not pass external mmc_cmd structure to mmc_send_op_cond_iter()
The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:54:09 +03:00
Andrew Gabbasov
a626c8d418 mmc: Avoid extra duplicate entry in mmc device structure
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:53:52 +03:00
Yangbo Lu
5a8dbdc6b4 mmc: fsl_esdhc: Add adapter card type identification support
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:19 -07:00
Przemyslaw Marczak
34dd928492 mmc: print SD/eMMC type for inited mmc devices
Depending on the boot priority, the eMMC/SD cards,
can be initialized with the same numbers for each boot.

To be sure which mmc device is SD and which is eMMC,
this info is printed by 'mmc list' command, when
the init is done.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-02-23 19:49:49 +02:00
Andrew Gabbasov
fc5b32fbf3 mmc: Skip changing bus width for MMC cards earlier than version 4.0
Wider bus widths (larger than default 1 bit) appeared in MMC standard
version 4.0. So, for MMC cards of any earlier version trying to change
the bus width (including ext_csd comparison) does not make any sense.
It may work incorrectly and at least cause unnecessary timeouts.
So, just skip the entire bus width related activity for earlier versions.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-01-19 17:41:52 +02:00
Andrew Gabbasov
bf4770731c mmc: Avoid redundant switching to 1-bit bus width for MMC cards
If all the commands switching an MMC card to 4- or 8-bit bus width fail,
and the bus width for the controller and the driver is still set
to default 1 bit, there is no need to send one more command to switch
the card to 1-bit bus width. Also, if the card or host controller do not
support wider bus widths, there is no need to send a switch command at all.

However, if one of switch commands succeeds, but the subsequent ext_csd
fields comparison fails, the card should be switched to some other bus width
(next in the list for the loop), or to default 1-bit bus width as a last
resort. That's why it would be incorrect to just remove the 1-bit bus width
case from the list, it should still be processed in some cases.

panto: Minor cosmetic edit removing superfluous parentheses.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-01-19 17:41:52 +02:00
Diego Santa Cruz
9e41a00b57 mmc: extend mmcinfo output to show partition write reliability settings
This extends the mmcinfo hardware partition info output to show
partitions with write reliability enabled with the "WRREL" string.
If the partition does not have write reliability enabled the "WRREL"
string is omitted; this is analogous to the ehhanced attribute.

Example output:

Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
Erase Group Size: 8 MiB
HC WP Group Size: 16 MiB
User Capacity: 13.8 GiB ENH WRREL
User Enhanced Start: 0 Bytes
User Enhanced Size: 512 MiB
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH WRREL
GP2 Capacity: 64 MiB ENH WRREL

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:41:51 +02:00
Diego Santa Cruz
8dda5b0e60 mmc: extend the mmc hardware partitioning API with write reliability
The eMMC partition write reliability settings are to be set while
partitioning a device, as per the eMMC spec, so changes to these
attributes needs to be done in the hardware partitioning API.
This commit adds such support.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:41:51 +02:00
Diego Santa Cruz
ac9da0e08c mmc: add API to do eMMC hardware partitioning
This adds an API to do hardware partitioning on eMMC devices. The
new mmc_hwpart_config() function does the partitioning in one go.
As the different attributes and partitioning options on eMMC may
be interdependent validation has to be done based on the complete
partitioning configuration. The function accepts three modes:

- MMC_HWPART_CONF_CHECK: just validates that the configuration
  is valid.
- MMC_HWPART_CONF_SET: validates and sets all the fields in
  EXT_CSD but without setting the "partitioning completed" bit,
  and thus is reversible.
- MMC_HWPART_CONF_COMPLETE: does everything and is thus not
  reversible.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:41:45 +02:00
Diego Santa Cruz
9cf199ebcf mmc: the ext_csd data may be used during init even if reading failed
The mmc_startup() function uses the ext_csd data even if reading it
from the mmc device failed. This bug was introduced in commit
bc897b1d4d. We now bail out if
reading it fails, this should not be a problem as ext_csd was
introduced in MMC 4.0 and this code is conditional on MMC >= 4.0.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:04:48 +02:00
Diego Santa Cruz
8a0cf49010 mmc: eMMC partitioning data is not effective till partitioning completed
The eMMC spec says that partitioning is only effective after the
PARTITION_SETTING_COMPLETED is set in EXT_CSD (and a power cycle was done,
but that we cannot know). Thus the partition sizes and attributes should
be ignored when that bit is not set, otherwise the various capacities
are not coherent (e.g., the user data capacity will be that of the
unpartitioned device while partition sizes would be non-zero).

Prescence of non-zero partitioning data is nevertheless still used to
activate the high-capacity size definitions (EXT_CSD_ERASE_GROUP_DEF)
as it is necessary to set that to write any of the partitioning fields
in EXT_CSD, so having partitioning data means someone previously
activated that and we should keep it activated.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:04:48 +02:00
Diego Santa Cruz
037dc0ab5d mmc: read the high capacity WP group size for eMMC
Read the eMMC high capacity write protect group size at mmc device
initialization. This is useful to correctly partition an eMMC device,
as partitions need to be aligned to this size.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
a4ff9f83f5 mmc: fix erase_grp_size computation with high-capacity size definition
The erase_grp_size in struct mmc is to be a size in 512-byte sectors
but the code used to compute it for eMMC when EXT_CSD_ERASE_GROUP_DEF is
enabled computed it as bytes, leading to erase sizes and alignment
much larger than what is actually required by the mmc device.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
a7f852b688 mmc: read the size of eMMC enhanced user data area
This modification reads the size of the eMMC enhanced user data area
upon initialization of an mmc device, it will be used later by
mmcinfo.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
f8e89d6716 mmc: computation of eMMC GP partition size was missing 512 KiB factor
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
0c453bb76c mmc: incomplete test to switch to high-capacity group size definitions
The eMMC spec mandates that the high-capacity group size definitions
should be enabled when the device is partitioned (by setting
ERASE_GROUP_DEF in EXT_CSD). The current test to determine when this is
required misses a few cases. In particular a device may have been
partitioned without setting the enhanced attribute on any partition
or partitioning may be completed without creating any extra partitions.

This change moves the code to set ERASE_GROUP_DEF to after reading
all partition information. It is also enabled when
PARTITIONING_SETTING_COMPLETED is set as it is necessary to enable
ERASE_GROUP_DEF before setting that bit, so it means that the user
previously switched to the high capacity definitions.

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:02:29 +02:00
Diego Santa Cruz
c3dbb4f9b7 mmc: extend mmcinfo to show enhanced partition attribute
This extends the mmcinfo command's output to show which eMMC partitions
have the enhanced attribute set. Note that the eMMC spec says that
if the enhanced attribute is supported then the boot and RPMB
partitions are of the enhanced type.

The output of mmcinfo becomes:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB ENH
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH
GP2 Capacity: 64 MiB ENH

Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
2015-01-19 17:01:34 +02:00
Andrew Gabbasov
5af8f45cd0 mmc: Fix block length for DDR mode
Block length for write and read commands is fixed to 512 bytes
when the card is in Dual Data Rate mode. If block length read from CSD
is different, make sure the driver will use correct length
in all further calculations and settings.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:08:38 +02:00
Andrew Gabbasov
201d5ac438 mmc: Fix Dual Data Rate capability recognition
Since the driver doesn't work in 1.2V or 1.8V signaling level modes,
Dual Data Rate mode can be supported by the driver only if it is supported
by the card in regular 3.3V mode. So, check for a particular single
bit in card type field.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:08:21 +02:00
Andrew Gabbasov
786e8f818c mmc: Fix handling of bus widths and DDR card capabilities
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.

Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.

This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.

Also, some clean up is made with errors handling and code syntax layout.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-12-12 21:08:06 +02:00
Markus Niebel
edab723b47 MMC: add MMC_VERSION_5_0
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2014-12-12 20:34:20 +02:00
Markus Niebel
d7b2912991 MMC: fix user capacity for partitioned eMMC card
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2014-12-12 20:28:04 +02:00
Lubomir Popov
e75eaf100b mmc: Cosmetic fix for nicer, aligned device list printout
If print_mmc_devices() was called with a '\n' separator (as done
for example by the "mmc list" command), it offset the 2-nd and
all subsequent lines by one space. Fixing this.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
2014-12-12 20:08:47 +02:00
Paul Kocialkowski
95de9ab201 mmc: Board-specific MMC power initializations
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:40 -05:00
Mario Schuknecht
786a27b7ec mmc: Fix mmc bus width
After setting the bus width, the extended CSD register is read. Some selected
fields are compared with previously read extended CSD register fields. In this
comparison the EXT_CSD_ERASE_GROUP_DEF field is compared. But this field is
previously written under certain circumstances. And then the comparison fails.

Only compare read-only fields. Therefore compare field EXT_CSD_HC_WP_GRP_SIZE
instead of field EXT_CSD_ERASE_GROUP_DEF.

Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03 17:26:50 +03:00
Peter Bigot
6dc93e7087 mmc: restore capacity when switching to partition 0
The capacity and lba for an MMC device with part_num 0 reflects the
whole device.  When mmc_switch_part() successfully switches to a
partition, the capacity is changed to that partition.  As partition 0
does not physically exist, attempts to switch back to the whole device
will indicate an error, but the capacity setting for the whole device
must still be restored to match the partition.

Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03 17:26:50 +03:00
Hannes Petermaier
021a80559f mmc: fix ERASE_GRP_DEF handling
if we set manually this bit on the eMMC card using mmc_switch(...),
we also have to set it within our (before read) internal structure
'ext_csd'.

Otherwise following checks on this will fail.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-10-03 17:26:49 +03:00
Jeroen Hofstee
750121c350 mmc: prevent some warnings with make W=1
Add missing prototypes for global functions and
make local functions static.

cc: panto@antoniou-consulting.com
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-18 17:53:24 -04:00
Jeroen Hofstee
cee9ab7cb6 dirvers: mmc: use __weak
use weak instead of alias to prevent some clang warnings.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-18 17:53:23 -04:00
Stephen Warren
d4622df342 mmc: return meaningful error codes from mmc_select_hwpart
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.

Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-06-12 14:15:59 +03:00
Albert ARIBAUD
cc49da249c Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-06-02 08:43:48 +02:00
Stephen Warren
d235628434 mmc: provide a select_hwpart implementation for get_device()
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-05-23 12:11:44 +03:00
Andrew Gabbasov
6b2221b008 mmc: Handle switch error status bit in MMC card status
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2014-05-23 11:34:33 +03:00
Mateusz Zalega
d803fea576 mmc: postponed needless timer initialization
mmc_init() doesn't call get_timer() anymore if MMC is already
initialized.

<panto> Minor formatting fix.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
2014-05-23 11:19:53 +03:00
Jaehoon Chung
d22e3d46a9 mmc: support the DDR mode for eMMC
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
8caf46d189 mmc: remove the unnecessary define and fix the wrong bit control
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Lukasz Majeski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Tom Rini
33ace362fd mmc: Add 'mmc rst-function' sub-command
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work.  Details on this being
required will be part of the eMMC datasheet.  Also add using this
command to the dra7xx README.

* Whitespace fix by panto

Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:02:58 +03:00
Pantelis Antoniou
93bfd61677 mmc: Split mmc struct, rework mmc initialization (v2)
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.

On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.

Typically the initialization got something like this in every driver.

	struct mmc *mmc = malloc(sizeof(struct mmc));
	memset(mmc, 0, sizeof(struct mmc);
	/* fill in fields of mmc struct */
	/* store private data pointer */
	mmc_register(mmc);

By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:

	struct mmc = mmc_create(&cfg, priv);

All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.

Changes since v1:

* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 12:58:56 +02:00
Pantelis Antoniou
ab769f227f mmc: Remove ops from struct mmc and put in mmc_ops
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.

This makes the mmc structure smaller as well as conserving
code space (in theory).

All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.

Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 11:32:10 +02:00
Tom Rini
614b2bf1c9 cmd_mmc.c: Drop open/close mmc sub-commands
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform.  Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.

Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
5a99b9de1a cmd_mmc.c: Add bootbus mmc sub-command
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).

Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Tom Rini
792970b0a3 cmd_mmc.c: Add 'partconf' command to mmc
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]).  Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.

Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Stephen Warren
def816a2ba mmc: set rca to 1 for MMC cards
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 17:34:06 +02:00