Replace the ad-hoc erase operation implementation with a simple spi_mem_op
implementation of the same functionality. This is a minor optimization and
removal of the ad-hoc code.
This however also changes the behavior of the execution of the erase
opcode from two separate transfer requests to the SPI NOR driver to
one transfer request to the SPI NOR driver. The former was how U-Boot
behaved before the SPI NOR framework was imported and the later was
introduced by the SPI NOR framework. The former is more optimal, so
keep that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Ashish Kumar <Ashish.kumar@nxp.com>
Add Macronix MX66U2G45F flash device description.
This is a 256 MiB part.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Vignesh R <vigneshr@ti.com>
[jagan: use 'g' instead of 'f' in flash name]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now the "spi-flash" compatible has been removed in the DTS files,
remove this compatible from sf_probe to finally use the Linux "jedec,spi-nor"
compatible.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for SPANSION s25fl064l
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Vignesh R <vigneshr@ti.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
spi_flash and spi_flash_ids are no longer needed after SPI NOR
migration. Remove them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible
SPI Flash device nodes. Therefore make U-Boot also to look for the same
compatible string so that we can use Linux DTS files as is.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync changes from Linux SPI NOR framework to add 4 byte addressing
support. This is required in order to support flashes like MT35x
that no longer support legacy Bank Address Register(BAR) way of accessing
>16MB region.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
controllers.
Therefore, add spi-mem support to spi-nor-core as a way to support SPI
controllers with MMIO interface. SPI MEM layer takes care of translating
spi_mem_ops to spi_xfer()s in case of legacy SPI controllers.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
SPI flash based MTD devs can be registered/unregistered at any time
through the sf probe command or the spi_flash_free() function.
This commit does not try to fix the root cause as it would probably
require rewriting most of the code and have an mtd_info object
instance per spi_flash object (not to mention that the the spi-flash
layer is likely to be replaced by a spi-nor layer ported from Linux).
Instead, we try to be as safe as can be by checking the code returned
by del_mtd_device() and complain loudly when there's nothing we can
do about the deregistration failure. When that happens we also reset
sf_mtd_info.priv to NULL, and check for NULL pointer in the mtd hooks
so that -ENODEV is returned instead of hitting a NULL pointer
dereference exception when the MTD instance is later accessed by a user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The DM implementation of spi_flash_free() does not unregister the MTD
device before removing the spi dev object. This leads to a use-after-free
bug when the MTD device is later accessed by a MTD user (observed when
attaching the device to UBI after env_sf_load() has called
spi_flash_free()).
Implement ->remove() and call spi_flash_mtd_unregister() from there.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_mtd_register() can be called several times and each time it
will register the same mtd_info instance like if it was a new one.
The MTD ID allocation gets crazy when that happens, so let's track the
status of the sf_mtd_info object to avoid that.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.
So macro for this micron manufacturer id.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present spi_flash_cmd_read_ops() allocates and frees a few bytes of
memory every time it is called. It is faster to use the stack for this
and this is now supported by the minimum GCC version required by U-Boot.
Remove the allocation and use a variable-sized array instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we don't have to deal with the command-line flag we can simplify
the code for detecting the emulator. Remove the lookup based on the SPI
specification, relying just on the device tree to locate the emulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add logging to aid debugging features in these drivers. Also drop some
code in sandbox_spi_xfer() which is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support specifying SPI flash devices to use in the device
tree and on the command line. Drop the second option, since it is a pain
to support nicely with driver model, and unnecessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for 2 new XMC (Wuhan Xinxin Semiconductor
Manufacturing Corp) SPI NOR chips.
This support can be enabled by selecting the SPI_FLASH_XMC Kconfig
option.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for SPANSION s25fl128l
Signed-off-by: Clément Laigle <c.laigle@catie.fr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed , at the end of } ]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This commit adds paired dev info for winbond w25q16jv
(tested w25q16jvssiq with a i.mx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Macronix mx25l1633e nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Gigadevice gd25q16c nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This commit adds the following flashes to the id-table
- W25Q16JV
- W25Q32JV
- W25Q64JV
- W25Q128JV
- W25Q256JV
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The N25Q256(A) datasheet clearly states that this device does have
a Flag Status Register and does update FSR PEC bit 7 during Program
and Erase cycles to indicate the cycle is in progress. Enable the
FSR PEC bit polling on this device to prevent data corruption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tom Rini <trini@konsulko.com>
Move the strdup() call so that it is only done when we know we will bind
the device.
Reported-by: Coverity (CID: 131216)
Signed-off-by: Simon Glass <sjg@chromium.org>
This flash IC is used in some chromebook models
manufactured by Bitland.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The clean_bar() function resets the SPI NOR BAR register to 0, but
does not set the flash->curr_bar to 0 , therefore those two can get
out of sync, which could ultimatelly result in corrupted flash content.
The simplest test case is this:
=> mw 0x10000000 0x1234abcd 0x4000
=> sf probe
=> sf erase 0x1000000 0x10000
=> sf write 0x10000000 0x1000000 0x10000
=> sf probe ; sf read 0x12000000 0 0x10000 ; md 0x12000000
That is, erase a sector above the 16 MiB boundary and write it with
random pre-configured data. What will actually happen without this
patch is the sector will be erased, but the data will be written to
BAR 0 offset 0x0 in the flash.
This is because the erase command will call write_bar()+clean_bar(),
which will leave flash->bank_curr = 1 while the hardware BAR registers
will be set to 0 through clean_bar(). The subsequent write will also
trigger write_bar()+clean_bar(), but write_bar checks if the target
bank == flash->bank_curr and if so, does NOT reconfigure the BAR in
the SPI NOR. Since flash->bank_curr is still 1 and out of sync with
the HW, the condition matches, BAR programming is skipped and write
ends up at address 0x0, thus corrupting flash content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Added support for is25wp032, is25wp064 and is25wp128.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for the SST sst26wf016, sst26wf032
and sst26wf064 flash IC.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
sst26wf flash series block protection implementation differs
from other SST series, so add specific implementation
flash_lock/flash_unlock/flash_is_locked functions for sst26wf
flash ICs.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure the user is notified instead of silently returning an error.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This SUNXI variant SPL SPI code doesn't use either SPI or
SPL_FLASG subsystems due to size constraints and also placing
this code in drivers/mtd/spi will unnecessary build SPI_FLASH
code(if defined) which never required, hence moved to arch area.
And also renamed the file according to kconfig which resembles
proper name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
spi_flash_probe_tail is now only called from spi_flash_probe, hence we
can merge its body into spi_flash_probe.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Commit ba45756 ("dm: x86: spi: Convert ICH SPI driver to driver model")
removed the last usage of the spi_flash_probe_fdt function, rendering it
obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Command bytes are part of the written bytes and they should be taken into
account when sending a spi transfer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For some SPI controllers it's not possible to keep the CS active between
transfers and they are limited to a known number of bytes.
This splits spi_flash reads into different iterations in order to respect
the SPI controller limits.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This spi-nor is 4Mbit/512KB
Fixes: b4fbcbc5a5 ("mtd/spi: add support for is25lq040b")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI
symbol. But despite its generic name, the actual only use case for this
is to provide SPI flash support to the SPL, which requires
CONFIG_SPL_SPI_FLASH_SUPPORT to be defined.
Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This
avoids doing this explicitly in the defconfig, and fixes SPI booting on
the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with
SPI flash).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The content of Bank Address Register (BAR) is volatile. It is cleared
after power cycle or reset command (RESET F0h).
Some memories (like e.g. s25fl256s) use it to access memory larger than
0x1000000 (16 MiB).
The problem shows up when one:
1. Reads/writes/erases memory > 16 MiB
2. Calls "reset" u-boot command (which is not causing BAR to be cleared)
In the above scenario, the SoC ROM sends 0x000000 address to read SPL.
Unfortunately, the BA24 bit is still set and hence it receives content
from 0x1000000 (16 MiB) memory address.
As a result the SoC aborts and we hang. Only power cycle can take the
SoC out of this state.
How to reproduce/test:
sf probe; sf erase 0x1200000 0x800000; reset
sf probe; sf erase 0x1200000 0x800000; sf write 0x11000000 0x1200000 0x800000; reset
sf probe; sf read 0x11000000 0x1200000 0x800000; reset
Signed-off-by: Lukasz Majewski <lukma@denx.de>
[Fixed comment text on clean_bar function]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi-specific SPI load routine only knows how to load a legacy
U-Boot image.
Teach it how to handle FIT images as well, simply by providing the
existing SPL FIT loader with the right loader routine to access the SPI
NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Peter Kosa <kope@madnet.sk>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Spansion S25FS256S and S25FL256S flashes have equal JEDEC ID and ext ID.
As far as S25FL256S occures in spi_flash_ids before S25FS256S, U-Boot
incorrectly detects FS flash as FL. Thus its better to compare with
S25FS256S first.
Signed-off-by: Vsevolod Gribov <vgribov@larch-networks.com>
[Added S-o-b]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The flash chip is 2 MiB , organized as 32 x 64 kiB sectors .
Rectify the entry to match the datasheet, reality and Linux SNOR IDs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add MT35XU512ABA1G12 parameters to NOR flash parameters array.
The MT35XU512ABA1G12 only supports 1 bit mode and 8 bits. It can't support
dual and quad. Supports subsector erase with 4KB granularity, have support
of FSR(flag status register) and flash size is 64MB.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
On some flash (like Macronix), QE (quad enable) bit is in the same
status register as BP# bits, and we need preserve its original value
during a reboot cycle as this is required by some platforms (like
Intel ICH SPI controller working under descriptor mode).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[Refined code for readability]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add the print message to tell us why the erase operation doesn't work.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This adds support for Macronix flash MX25U6435F (device ID 0xc22537).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Addresses passed on to readl and writel are expected to be of the same
size as a pointer. Change the parameter types of sunxi_spi0_read_data()
to make the compiler happy and allow a warning-free aarch64 compile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit c56ae7519f.
Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.
Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.
Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.
Indeed the SPI controller driver is not aware of the SPI protocol switch.
Further patches will fix the support of Micron QSPI memories.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards may want to use these subsystems with of-platdata in SPL. Add
support for this by avoiding any device tree access in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds support for the Macronix MX66U51235F,
MX66L1G45G and Micron MT25QU02G, MT25QL02G flash parts.
Signed-off-by: Radu Bacrau <dumitru.bacrau@intel.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Radu Bacrau <radu.bacrau@gmail.com>
[Update proper commit header and 80-line cut on body]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Somehow an int returning function without a return statement sneaked
in, fix it.
Also fix some whitespace damage on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
s25fs512s and s25fl512s_256k have common id information
till 5 bytes and 6th byte have different family id
like FS and FL-S as 0x81 and 0x80.
Reported-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
- fix single line comments
- remove unneeded spaces
- ascending order of include files
- rename SPI DATAFLASH to dataflash
- rename SPI DataFlash to dataflash
- return NULL replaced with error code
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch fixed the add_dataflash return logic,
so-that it can handle both jedec and older chips
same as Linux.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Flash id detection should be the first step to enumerate
the connected flash on the board, once ie done checking
with respective id codes locally in the driver all this
should be part of jedec_probe instead of id detection and
validated through flash_info{} table separatly.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
dataflash doesn't require options, memory_map from spi.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.
So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_write_bar-> write_bar
spi_flash_write_bar -> read_bar
spi_flash_cmd_wait_ready -> spi_flash_wait_till_ready
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Use small 'd' in s25s512s ext_jedec
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
For readability use small letter's with flash name.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Remove unneeded/non-meaningful commit message on
params and flash.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
For this:
- Removed spansion_s25fss_disable_4KB_erase code
- Add SECT_4K for S25FS512S chip
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Add Spansion S25FS256S_64K spi flash to the list of spi_flash_ids.
In spansion S25FS-S family the physical sectors are grouped as
normal and parameter sectors. Parameter sectors are 4kB in size
with 8 set located at the bottom or top address of a device.
Normal sectors are similar to other flash family with sizes of
64kB or 32 kB.
To erase whole flash using sector erase(D8h or DCh) won't effect
the parameter sectors, so in order to erase these we must use 4K
sector erase commands (20h or 21h) separately.
So better to erase the whole flash using 4K sector erase instead
of detecting these family parts again and do two different erase
operations.
Cc: Yunhui Cui <yunhui.cui@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
INFO6 is for tabulating 6 byte flash parts, Ex: S25FS256S_64K
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
So, now SPI_FLASH_ID_MAX_LEN is 6 bytes useful for
few spansion flash families S25FS-S
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
