A rather common kind of external watchdog circuit is one that is kept
alive by toggling a gpio. Add a driver for handling such a watchdog.
The corresponding linux driver apparently has support for some
watchdog circuits which can be disabled by tri-stating the gpio, but I
have never actually encountered such a chip in the wild; the whole
point of adding an external watchdog is usually that it is not in any
way under software control. For forward-compatibility, and to make DT
describe the hardware, the current driver only supports devices that
have the always-running property. I went a little back and forth on
whether I should fail ->probe or only ->start, and ended up deciding
->start was the right place.
The compatible string is probably a little odd as it has nothing to do
with linux per se - however, I chose that to make .dts snippets
reusable between device trees used with U-Boot and linux, and this is
the (only) compatible string that linux' corresponding driver and DT
binding accepts. I have asked whether one should/could add "wdt-gpio"
to that binding, but the answer was no:
https://lore.kernel.org/lkml/CAL_JsqKEGaFpiFV_oAtE+S_bnHkg4qry+bhx2EDs=NSbVf_giA@mail.gmail.com/
If someone feels strongly about this, I can certainly remove the
"linux," part from the string - it probably wouldn't the only place where
one can't reuse a DT snippet as-is between linux and U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The driver will use a syscon regmap as backend and supports both
16 and 32 size value. The value will be stored in the CPU's endianness.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With device tree binding migration to yaml it is difficult to synchronize
the binding from Linux kernel to U-Boot.
Instead of maintaining the same dt bindings, this patch adds in the U-Boot
documentation the path to the device tree bindings in Linux kernel for
STMicroelectronics devices, when they are used without modification.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add links for referenced text files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
RTC devices could provide battery-backed memory that can be used for
storing the reboot mode magic value.
Add a new reboot-mode back-end that uses RTC to store the reboot-mode
magic value. The driver also supports both endianness modes.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A use case for controlling the boot mode is when the user wants
to control the device boot by pushing a button without needing to
go in user-space.
Add a new backed for reboot mode where GPIOs are used to control the
reboot-mode. The driver is able to scan a predefined list of GPIOs
and return the magic value. Having the modes associated with
the magic value generated based on the GPIO values, allows the
reboot mode uclass to select the proper mode.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On J721e and J7200, MCU R5 core (boot master) itself would run Device
Manager (DM) Firmware and interact with TI Foundational Security (TIFS)
firmware to enable DMA and such other Resource Management (RM) services.
So, during R5 SPL stage there is no such RM service available and ti_sci
driver will have to directly interact with TIFS using DM to DMSC
channels to request RM resources.
Therefore add DT binding and driver for the same. This driver will
handle Resource Management services at R5 SPL stage.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-4-vigneshr@ti.com
This uses the newly-added dm_gpio_get_values_as_int_base3 function to
implement a sysinfo device. The revision map is stored in the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Document the bindings for fsl,anatop-regulator
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
update ls1028aqds networking protocol, config in ls1021atwr, env in ls1012a
Add seli3 board support, booke watchdog, update eTSEC support in ppc-qemu
Add DM_SERIAL and lpuart in sl28, add DM_ETH support for some of powerpc platforms
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the Freescale TSEC node DT bindings doc requires a <reg>
property in the TSEC node. But this might not always be the case.
In the upstream Linux kernel, there is no DT bindings doc for it
but the kernel driver tests a subnode of a name prefixed with
"queue-group", as we can see from gfar_of_init():
for_each_available_child_of_node(np, child) {
if (!of_node_name_eq(child, "queue-group"))
...
in drivers/net/ethernet/freescale/gianfar.c
Update our DT bindings to describe this alternate description.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Per the upstream Linux kernel doc:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
There are two ways to describe a fixed PHY attached to an Ethernet
device. This updates our dt-bindings doc to add the old DT bindings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
An entry is missing in the FSP-S devicetree bindings, and as a result
the description for the next few following entries is off by one line.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Implement voltage regulators interfaced by the SCMI voltage domain
protocol. The DT bindings are defined in the Linux kernel since
SCMI voltage domain and regulators patches [1] and [2] integration
in v5.11-rc7.
Link: [1] 0f80fcec08
Link: [2] 2add5cacff
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This PWM is used in rk3399-gru-bob and rk3399-gru-kevin to control
the display brightness. We can only change the duty cycle, so on
set_config() we just try to match the duty cycle that dividing duty_ns
by period_ns gives us. To disable, we set the duty cycle to zero while
keeping the old value for when we want to re-enable it.
The cros_ec_set_pwm_duty() function is taken from Depthcharge's
cros_ec_set_bl_pwm_duty() but modified to use the generic pwm type.
The driver itself is very loosely based on rk_pwm.c for the general pwm
driver structure.
The devicetree binding file is from Linux, before it was converted to
YAML at 5df5a577a6b4 ("dt-bindings: pwm: Convert google,cros-ec-pwm.txt
to YAML format") in their repo.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmBi3oscHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKr+CACDQJT4hGCDwc7XFjOw
RN0aGRC6eGF4q3kL4VjBazCM1SBNs3vdVZV+bnYl3ioSNzy43K7CyFqqUlJH7CJV
dakvNn71xVoQD3Xw3+I4ALibbD/tlli4vwMOeN4KlWCIdNrRrtUOQpli0M0BVDkL
0IWMDf6OLAfw1uytubsQBVitFBQoiuE3ihSphoyTOFwQdI+xsMue5uVq+O0kDqU4
gotBzmoSq5LONyNSdpHxXqujU4oXkuOr/TsVTOoRtEkQ63zVbfNWOg951is+UaHa
F7f6W+cWdlb+HBs6TFb+Gva0TMmyWIH05jyIS52k6uFVM0tyFCOJFeZp81cjPP4L
O3KI
=ywRG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:
- two pins provided in a ternary arrangement, for 9 combinations.
- reading from the EC
Add a binding doc and drop the unused #defines as well.
Example:
U-Boot 2021.01-rc5
CPU: Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
DRAM: 3.9 GiB
MMC: sdmmc@1b,0: 1, emmc@1c,0: 2
Video: 1024x768x32 @ b0000000
Model: Google Coral (memconfig 5, SKU 3)
This depends on the GPIO series:
http://patchwork.ozlabs.org/project/uboot/list/?series=228126
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Dump adc-keys bindings documentation from Linux kernel source tree from
commit 698dc0cf9447 ("dt-bindings: input: adc-keys: clarify
description").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add optional properies to disable usb2 or usb3 ports, they are used
when provided ports are not used on some special platforms.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
This documentation has been taken from Linux commit 3d7db0f11c7a ("spi: dw:
Refactor mid_spi_dma_setup() to separate DMA and IRQ config"), immediately
before the file was deleted and replaced with a yaml version. Additional
compatible strings from newer versions have been added, as well as a few
U-Boot-specific ones.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This renames power domains to match the names on the k210 datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add information about how to set SMBIOS properties using the devicetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a simple binding file for this, so that it is clear what this binding
directory is for.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add dt-binding for MediaTek USB3 DRD Driver which it's ported
from the Linux kernel DTS binding:
Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
Commit ID:
34d0545978b6 ("dt-bindings: usb: mtu3: fix typo of DMA clock name")
Due to Dual-Role switch is not supported in Uboot, some properties
are removed or changed.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add bindings for common properties, include maximum-speed,
dr_mode and phy_type
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinmux property allows for smaller and more compact device trees,
especially when there are many pins which need to be assigned individually.
Instead of specifying an array of strings to be parsed as pins and a
function property, the pinmux property contains an array of integers
representing pinmux groups. A pinmux group consists of the pin identifier
and mux settings represented as a single integer or an array of integers.
Each individual pin controller driver specifies the exact format of a
pinmux group. As specified in the Linux documentation, a pinmux group may
be multiple integers long. However, no existing drivers use multi-integer
pinmux groups, so I have chosen to omit this feature. This makes the
implementation easier, since there is no need to allocate a buffer to do
endian conversions.
Support for the pinmux property is done differently than in Linux. As far
as I can tell, inversion of control is used when implementing support for
the pins and groups properties to avoid allocating. This results in some
duplication of effort; every property in a config node is parsed once for
each pin in that node. This is not such an overhead with pins and groups
properties, since having multiple pins in one config node does not occur
especially often. However, the semantics of the pinmux property make such a
configuration much more appealing. A future patch could parse all config
properties at once and store them in an array. This would make it easier to
create drivers which do not function solely as callbacks from
pinctrl-generic.
This commit increases the size of the sandbox build by approximately 48
bytes. However, it also decreases the size of the K210 device tree by 2
KiB from the previous version of this series.
The documentation has been updated from the last Linux commit before it was
split off into yaml files.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dump SCMI DT bindings documentation from Linux kernel source
tree v5.8-rc1.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some boards want to reserve extra regions of memory. Add a 'chosen'
property to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some devices can wake the system from sleep, e.g opening the lid on a
clamshell or moving a USB mouse.
Add a wake to specify this for USB devices and add the settings for Apollo
Lake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.
This can be handled by a generic driver along with some information in the
device tree.
Add a generic i2c driver for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
The K3 J7200 SoCs have two dual-core Arm R5F clusters/subsystems, with
2 R5F cores each, one in each of the MCU and MAIN voltage domains.
These clusters are a revised version compared to those present on
J721E SoCs. Update the K3 R5F remoteproc bindings with the compatible
info relevant to these R5F clusters/subsystems on K3 J7200 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Add missing parameters to support full configuration of the latest FSP
MR6 release.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
- doc/device-tree-bindings/pinctrl/nexell,s5pxx18-pinctrl.txt added.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- i2c/nx_i2c.c: Some adaptions mainly because of changes in
"struct udevice".
- several Bugfixes in nx_i2c.c.
- the driver has been for s5p6818 only. Code extended appropriately
in order s5p4418 is also working.
- "probe_chip" added.
- pinctrl-driver/dt is used instead of configuring the i2c I/O-pins
in the i2c-driver.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
