The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Use CONFIG_SOC_KEYSTONE in common places instead of defining
a lot of "if def .. || if def " for different Keystone2 SoC types.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <trini@ti.com>
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
Flush UART3 xmit on enable if TEMT is broken
On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.
Signed-off-by: Manfred Huber <man.huber@arcor.de>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
This cast does not seem correct, since we should be writing to a pointer,
not a ulong.
This fixes the following warning on nds32:
-ns16550.c:49: warning: passing argument 2 of 'writeb' makes pointer from integer without a cast
Signed-off-by: Simon Glass <sjg@chromium.org>
Some platforms (e.g. IGEPv2 board) has a broken ns16550 UART that
does not set the TEMT bit when the transmitter is empty in SPL.
This makes U-Boot to hang while waiting for TEMT to be set.
Add a new option to avoid this:
CONFIG_SYS_NS16550_BROKEN_TEMT
16550 UART set the Transmitter Empty (TEMT) Bit when all output
has finished and the transmitter is totally empty. U-Boot waits
for this bit to be set to initialize the serial console. On some
broken platforms this bit is not set in SPL making U-Boot to
hang while waiting for TEMT. Define this option to avoid it.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
TEMT is set when the transmitter is totally empty and all output has
finished.
This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
Having both USBTTY and CONFIG_SERIAL_MULTI enabled in SPL, the
usbtty.c file is protected in Makefile to not be compiled into
the SPL. Yet, the ns16550 serial driver does not contain such
protection. Add it to avoid missing symbol error.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
also fix NS16550_init() as we need 16x divider
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
If CONFIG_SYS_NS16550_MEM32 is defined then 32 bit memory
mapped access will be used to read/write the uart registers.
This is especially useful for SoC devices that implement 16550
compatible uarts but that have peripheral access width constraints.
Signed-off-by: Dave Aldridge <fovsoft@gmail.com>
On some processors this ier register configuration is different
for ex. Marvell Armada100
This patch introduce CONFIG_SYS_NS16550_IER macro support to
unconditionally initialize this register.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Call watchdog_reset() upon newline. This is done here in putc
since the environment code uses a single puts() to print the complete
envrironment upon "printenv". So we can't put this watchdog call
in puts().
This is needed for boards with a very short watchdog timeout, like the
lwmon5 with a 100ms timeout. Without this patch this board resets in the
commands with long outputs, like "printenv" or "fdt print".
Note that the image size is not increased with this patch when
CONFIG_HW_WATCHDOG or CONFIG_WATCHDOG are not defined since the compiler
optimizes this additional code away.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix typo in comment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The x86 architecture exclusively uses Port-Mapped I/O (inb/outb) to access
the 16550 UARTs. This patch mimics how Linux selects between Memory-Mapped
and Port-Mapped I/O. This allows x86 boards to use CONFIG_SERIAL_MUTLI and
drop the custom serial port driver
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
ns16550 busyloops waiting for incoming byte causing watchdog to reboot
while waiting for a key press. A call to WATCHDOG_RESET in NS16550_getc
loop fixes it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Fix problems introduced in commit
7b5611cdd1 [inka4x0: Add hardware
diagnosis functions for inka4x0] which redefined MSR_RI which is
already used on PowerPC systems.
Also eliminate redundant definitions in ps2mult.h. More cleanup will
be needed for other redundant occurrences though.
Signed-off-by: Detlev Zundel <dzu@denx.de>
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error. This option will exclude all functions with exception of
NS16550_putc and NS16550_init. This will be used primarily to save space and
remove unused code from builds in which space is limited.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
According to the OMAP5912 Serial Interfaces Reference Guide (see
http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the
FIFO_EN enable bit in the FIFO Control Register (FCR) can only be
changed when the baud clock is not running, i. e. when both DLL and
DLH are set to 0.
Thus make sure that DLL and DLH are 0 when writing the FCR.
Signed-off-by: Wolfgang Denk <wd@denx.de>
