This patch adds booti support for RISC-V Linux kernel. The existing
bootm method will also continue to work as it is.
It depends on the following kernel patch which adds the header to the
flat Image. Gzip compressed Image (Image.gz) support is not enabled with
this patch.
https://patchwork.kernel.org/patch/10925543/
Tested on HiFive Unleashed and QEMU.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Karsten Merker <merker@debian.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Switch to use the generic helpers to access the MMD registers so that we
can used the same command also for C45 PHYs, C22 PHYs with direct and
indirect access and PHYs implementing a custom way to access the
registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
allow_unaligned(), switch_to_non_secure_mode(), and efi_init_obj_list() are
called in sequence in multiple places.
Move calls to allow_unaligned() and switch_to_non_secure_mode() to
efi_init_obj_list().
Remove unused includes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The list of PXE default paths contains ARCH and SOC specific paths, but
one PXE server can serve different board with the same ARCH and SOC.
This is the case for Turris Omnia and Turris Mox, where ARCH=arm and
SOC=mvebu.
If CONFIG_SYS_BOARD is defined, also try "default-$ARCH-$SOC-$BOARD"
path.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The "Mode :" line is the only one in "mmc info" output that has a
space in front of the colon. Drop the space to make it consistent
with the rest of the output, e.g.:
=> mmc dev 1 ; mmc info
switch to partitions #0, OK
mmc1 is current device
Device: sd@ee160000
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
^------------------------------ Remove this space
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
Bus Width: 1-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
clk_get_rate may return -ENODEV if the clock isn't valid.
Also, make the error cases go through a single path.
Fixes: ff8eee0330 ("cmd: clk: Add trivial implementation of clock dump
for DM")
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
-----BEGIN PGP SIGNATURE-----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=GUpA
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc2
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
Apply the following changes:
- Guard the 'gpt read' command by 'ifdef CONFIG_CMD_GPT_RENAME',
since 'gpt read' is not available on CMD_GPT_RENAME=n
- Prefix the {read,swap,rename} commands with one space for consistency
- Prefix the 'guid' commands with 'gpt' for consistency
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In case of a failure exit data may be passed to Exit() which in turn is
returned by StartImage().
Let the `bootefi` command print the exit data string in case of an error.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When printing an UEFI variable an error may arise while converting an
illegal hexadecimal value. In this case a buffer is leaked.
Close the memory leak. Provide an error message.
Reported-by: Coverity (CID 185830)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The field boot OptionalData in structure _EFI_LOAD_OPTIONS is for binary
data.
When we use `efidebug boot add` we should convert the 5th argument from
UTF-8 to UTF-16 before putting it into the BootXXXX variable.
When printing boot variables with `efidebug boot dump` we should support
the OptionalData being arbitrary binary data. So let's dump the data as
hexadecimal values.
Here is an example session protocol:
=> efidebug boot add 00a1 label1 scsi 0:1 doit1 'my option'
=> efidebug boot add 00a2 label2 scsi 0:1 doit2
=> efidebug boot dump
Boot00A0:
attributes: A-- (0x00000001)
label: label1
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit1
data:
00000000: 6d 00 79 00 20 00 6f 00 70 00 74 00 69 00 6f 00 m.y. .o.p.t.i.o.
00000010: 6e 00 00 00 n...
Boot00A1:
attributes: A-- (0x00000001)
label: label2
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit2
data:
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently in do_efi_boot_dump(), we directly read EFI variables from
related environment variables. To accommodate alternative storage
backends, we should switch to using the UEFI API instead.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
UEFI variables should be installed using well-defined API.
Currently we don't support much, but the value of OsIndicationsSupported
will be updated once some features are added in the future.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Add comments. Rename a variable.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
AVB 2.0 spec. revision 1.1 introduces support for named persistent values
that must be tamper evident and allows AVB to store arbitrary key-value
pairs [1].
Introduce implementation of two additional AVB operations
read_persistent_value()/write_persistent_value() for retrieving/storing
named persistent values.
Correspondent pull request in the OP-TEE OS project repo [2].
[1]: https://android.googlesource.com/platform/external/avb/+/android-9.0.0_r22
[2]: https://github.com/OP-TEE/optee_os/pull/2699
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
The objective is to provide a simple way to retrieve a BMP file,
and display it as splashscreen, from extlinux.conf file input.
For this, we take example on https://www.syslinux.org/wiki/
index.php?title=Menu#The_advanced_menu_system
and more particularly on MENU BACKGROUND chapter.
For this, add "menu background" support in pxe command.
As example, extlinux.conf content will look like:
# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
TIMEOUT 20
menu background ../splash.bmp
DEFAULT stm32mp157c-ev1-sdcard
LABEL stm32mp157c-ev1-sdcard
KERNEL /uImage
FDT /stm32mp157c-ev1.dtb
APPEND root=/dev/mmcblk0p6 rootwait rw earlyprintk console=ttySTM0,115200
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This reverts commit 65a97e7fcf.
The 'eeprom' command has been converted to work with DM_I2C in a patch
submitted around the same time as this commit:
commit 0c07a9b407 ("eeprom: Add device model based I2C support to eeprom command")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The current device model enabled eeprom code only works if
CONFIG_SYS_I2C_EEPROM_BUS is set.
This patch makes it work without that define so that the bus
number passed to 'eeprom_init' is used.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
-----BEGIN PGP SIGNATURE-----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=caQ+
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-3' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (3)
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
When using boot scripts it can become quite hard to understand
which commands are actually executed during bootup (e.g. where
is a kernel image loaded from or which DTB is in use).
Shell scripts suffer from a similar problem and many shells address
this problem with a command execution tracer (e.g. BASH has xtrace,
which can be enabled by "set -x").
This patch introduces a command tracer for U-Boot, which prints
every command with its arguments before it is executed.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The EBBR specification prescribes that we should have either an ACPI table
or a device tree but not both. Let us enforce this condition in the
`bootefi` command.
If the bootefi command is called without a device tree parameter use a
previously device tree or fall back to the internal device tree.
The fdt unit test should not be run on boards with an ACPI table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the current implementation, bootefi command and EFI boot manager
don't use load_image API, instead, use more primitive and internal
functions. This will introduce duplicated code and potentially
unknown bugs as well as inconsistent behaviours.
With this patch, do_efibootmgr() and do_boot_efi() are completely
overhauled and re-implemented using load_image API.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Use efi_root as parent handle for the loaded image.
LoadImage() should be called with BootPolicy = true by the boot manager.
Avoid duplicate free_pool().
Eliminate variable memdp which is not needed after anymore due to
"efi_loader: correctly split device path of loaded image".
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
All the non-boot-manager-based (that is, bootefi <addr>) code is put
into one function, do_bootefi_image().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
do_bootmgr_exec() is renamed to do_efibootmgr() as we put all the necessary
code into this function.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Efi_selftest code is unusual in terms of execution path in do_bootefi(),
which make that function complicated and hard to understand. With this
patch, all efi_selftest related code will be put in a separate function.
The change also includes expanding efi_run_prepare() and efi_run_finish()
in do_bootefi_exec().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
For simplicity, merge two functions.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Return error code of efi_install_configuration_table() when aborting from
efi_install_fdt().
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Carve out a function to handle the installation of the device tree
as a configuration table in system table.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
set_load_options() can fail, so it should return error code to stop
invoking an image.
In addition, set_load_options() now takes a handle, instead of
loaded_image_info, to utilize efi_load_image() in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The `efidebug dh` command shows handles and the installed protocols. For
most of the protocols implemented by U-Boot a short text was shown. But for
some only the GUID was displayed.
Provide the missing short texts for the following protocols: HII String,
HII Database, HII Config Routing, Simple Network, PXE Base Code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should consistently use the same name for protocol GUIDs as defined in
the UEFI specification. Not adhering to this rule has led to duplicate
definitions for the EFI_LOADED_IMAGE_PROTOCOL_GUID.
Adjust misnamed protocol GUIDs.
Adjust the text for the graphics output protocol in the output of the
`efidebug dh` command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This function supports getting both data address and length for
existing FIT subimage and FIT external data.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
The 'exception' command allows to test exception handling.
This implementation supports ARM, x86, RISC-V and the following exceptions:
* 'breakpoint' - prefetch abort exception (ARM 32bit only)
* 'unaligned' - data abort exception (ARM only)
* 'undefined' - undefined instruction exception
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reload the watchdog in the mass storage command ums
to avoid reboot during the usb waiting loop
when the host doesn't send any request.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The compiler is not happy when neither USB nor TFTP transport for DFU defined:
cmd/dfu.c: In function ‘do_dfu’:
cmd/dfu.c:31:8: warning: unused variable ‘devstring’ [-Wunused-variable]
char *devstring = argv[3];
^~~~~~~~~
cmd/dfu.c:30:8: warning: unused variable ‘interface’ [-Wunused-variable]
char *interface = argv[2];
^~~~~~~~~
Surround those variables by #ifdef expression.
More serious, that comes under same circumstances, is a compilation error due
to absence of macro parameter:
In file included from include/image.h:45,
from include/common.h:35,
from cmd/dfu.c:13:
include/command.h:207:24: error: expected expression before ‘,’ token
# define _CMD_HELP(x) x,
^
include/command.h:286:18: note: in expansion of macro ‘_CMD_HELP’
_cmd, _usage, _CMD_HELP(_help) _CMD_COMPLETE(_comp) }
^~~~~~~~~
include/command.h:290:3: note: in expansion of macro ‘U_BOOT_CMD_MKENT_COMPLETE’
U_BOOT_CMD_MKENT_COMPLETE(_name, _maxargs, _rep, _cmd, \
^~~~~~~~~~~~~~~~~~~~~~~~~
include/command.h:332:2: note: in expansion of macro ‘U_BOOT_CMD_COMPLETE’
U_BOOT_CMD_COMPLETE(_name, _maxargs, _rep, _cmd, _usage, _help, NULL)
^~~~~~~~~~~~~~~~~~~
cmd/dfu.c:70:1: note: in expansion of macro ‘U_BOOT_CMD’
U_BOOT_CMD(dfu, CONFIG_SYS_MAXARGS, 1, do_dfu,
^~~~~~~~~~
make[1]: *** [scripts/Makefile.build:279: cmd/dfu.o] Error 1
make: *** [Makefile:1518: cmd] Error 2
Put empty string unconditionally to have macro parameter present.
Fixes: 0f44d33536 ("dfu: Fix up the Kconfig mess")
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
This function supports getting both data address and length for
existing FPGA subimage and FPGA external data.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
-----BEGIN PGP SIGNATURE-----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=QdJl
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (2)
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
Following Ard's suggestion:
Runtime data sections are intended for data that is used by the runtime
services implementation.
Let's change the type to EFI_BOOT_SERVICES_DATA.
This also fixes booting of armv7 using efi and fdtcontroladdr.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add a command to control the watchdog devices. This is useful if the
watchdog is rather long running (eg. seconds) and it should be
controlled by scripts. It is also handy during debugging.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The command line is:
ln <interface> <dev[:part]> target linkname
Currently symbolic links are supported only in ext4 and only if the option
CMD_EXT4_WRITE is enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current code is plain wrong, and there's no need to have a mutable string,
so fix function type and remove the intermediate variable.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
A misplaced return statement lead to a memory leak in
efi_dump_single_var().
Reported-by: Coverity (CID 185829)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In `efidebug boot add iPXE scsi 0:1 snp-arm64.efi --foo` a parameter is
missing. Hence the command should not silently return as if everything were
ok but should display the usage info.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
"drivers" command prints all the uefi drivers on the system.
=> efi drivers
Driver Name Image Path
================ ==================== ====================
000000007ef003d0 <NULL> <built-in>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"devices" command prints all the uefi variables on the system.
=> efi devices
Scanning disk ahci_scsi.id0lun0...
Scanning disk ahci_scsi.id1lun0...
Found 4 disks
Device Device Path
================ ====================
000000007ef07ea0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
000000007ef00c10 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)
000000007ef00dd0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)
000000007ef07be0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)/HD(1,MBR,0x086246ba,0x800,0x40000)
000000007ef07510 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)/HD(2,MBR,0x086246ba,0x40800,0x3f800)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, there is no easy way to add or modify UEFI variables.
In particular, bootmgr supports BootOrder/BootXXXX variables, it is
quite hard to define them as u-boot variables because they are represented
in a complicated and encoded format.
The new command, efidebug, helps address these issues and give us
more friendly interfaces:
* efidebug boot add: add BootXXXX variable
* efidebug boot rm: remove BootXXXX variable
* efidebug boot dump: display all BootXXXX variables
* efidebug boot next: set BootNext variable
* efidebug boot order: set/display a boot order (BootOrder)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Without CONFIG_LED, we get
cmd/built-in.o: In function `show_led_state':
cmd/led.c:40: undefined reference to `led_get_state'
cmd/built-in.o: In function `do_led':
cmd/led.c:99: undefined reference to `led_get_by_label'
cmd/led.c:108: undefined reference to `led_set_state'
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Allow the 'gpio' command to match GPIO bank names regardless of the case
of each. While these are generally in upper case, it is useful to be able
to provide lower case with the command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the gpio command only shows GPIOs which are marked as in use.
This makes sense with 'gpio status' since we already have the '-a' flag
to indicate that all GPIOs should be shown. But when a particular GPIO is
requested, it seems better to always display it. At present the request is
simply ignored.
For example if GPIO a10 is not in use, then:
> gpio status a10
shows nothing, not even the function being used for that GPIO. With this
change, it shows the pin status:
> gpio status a10
a10: input: 0 [ ]
Add an extra parameter for this to avoid changing the existing flag
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the 'gpio' command in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Arguments are const and belong to the caller. Calling date in a hush
loop will yield different results from the second invocation.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Currently there are two problems in 'bootelf -p' (load elf by segments)
command:
- bss section is not flushed, so booted elf can have non zero values
in bss;
- at least on ARM there are 'CACHE: Misaligned operation at
range...' warnings
Use p_memsz instead of p_filesz during cache flushing for elf segment.
p_filesz doesn't include zero initialized memory (e.g. bss section),
which also should be flushed.
Align these cache flushes to line boundaries.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
Free resources upon failure.
Correct the function description.
As there is no need for any special address in the dummy memory device
path passed via the EFI_LOADED_IMAGE_PROTOCOL simply use 0 as address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
`bootefi selftest` fails on qemu-x86_defconfig if efi_selftest() is not
invoked using EFI_CALL().
Likewise we call the entry point of EFI payloads with
EFI_CALL(efi_start_image()).
entry_count indicates if we are in U-Boot (1) or in EFI payload code (0).
As we start in U-Boot code the initial value has to be 1.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove the duplicate code in efi_do_enter() and use efi_start_image() to
start the image invoked by the bootefi command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now efi_load_pe() returns the entry point or NULL in case of an
error. This does not allow to return correct error codes from LoadImage().
Let efi_load_pe() return a status code and fill in the entry point in the
corresponding field of the image object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch fixes the int-to-pointer-cast warning on aarch64.
Signed-off-by: Adam Heinrich <adam@adamh.cz>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The function, efi_init_obj_list(), can be shared in different pseudo efi
applications, like bootefi/bootmgr as well as my efishell. Moreover, it
will be utilized to extend efi initialization, for example, my "removable
disk support" patch and "capsule-on-disk support" patch in the future.
So with this patch, it will be moved to a new file, efi_setup.c, under
lib/efi_loader and exported, making no changes in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Remove lines deactivated by #if 1 #else
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
debug() support supports %p to print pointers.
The debug message is unique. So there is not need to write a possibly
distracting line number.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
It should not be necessary to adjust CMD_BOOTEFI_HELLO_COMPILE in config
files.
arch/arm/lib/crt0_arm_efi.S cannot be compiled in thumbs mode. We can
disable CMD_BOOTEFI_HELLO_COMPILE for CONFIG_CPU_V7M. So there is no longer
a need to disable it in stm32 configs.
helloworld.efi can be built without problems on x86_64. So there is no need
to disable it in chromebook_link64_defconfig and qemu-x86_64_defconfig.
Same is true for ARM V7A. So do not disable CMD_BOOTEFI_HELLO_COMPILE in
kp_imx6q_tpc_defconfig.
Some architecture checks are already make for EFI_LOADER. There is no need
to repeat them for CMD_BOOTEFI_HELLO_COMPILE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice.Chotard@st.com
Signed-off-by: Alexander Graf <agraf@suse.de>
When calling efi_dp_from_mem() use a named constant for the memory type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calling sata_scan() with a null pointer probably won't make much sense.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this file uses GPIO_OUTPUT and GPIO_INPUT as its sub-command
values. These are pretty generic names. Add a 'C' suffix to avoid possible
conflicts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The imgextract command runs a number of checks of
the specified fit. Where it checks for a load address
for compressed images the logic in the expression
is inverted as fit_image_check_comp returns 1 on
success and not 0.
cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable]
static char mtd_help_text[] =
^~~~~~~~~~~~~
When SYS_LONGHELP is not defined. After looking at how other commands
work, we should surround the whole help text (even its declaration) with
an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling
_CMD_HELP[1] on the help text variable argument to U_BOOT_CMD.
[1] https://elixir.bootlin.com/u-boot/latest/source/include/command.h#L181
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
And you get sub-command auto-completion for free.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It's way simpler this way, and we also gain auto-completion support for
free (MTD name auto-completion has been added with mtd_name_complete())
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The repeatable property is currently attached to the main command and
sub-commands have no way to change the repeatable value (the
->repeatable field in sub-command entries is ignored).
Replace the ->repeatable field by an extended ->cmd() hook (called
->cmd_rep()) which takes a new int pointer to store the repeatable cap
of the command being executed.
With this trick, we can let sub-commands decide whether they are
repeatable or not.
We also patch mmc and dtimg who are testing the ->repeatable field
directly (they now use cmd_is_repeatable() instead), and fix the help
entry manually since it doesn't use the U_BOOT_CMD() macro.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
test->time_ms[] is defined as unsigned. So use %u for printf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio is defined as unsigned int. So we should use %u when calling printf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure the block cache is cleared for the MMC device after it was
reinitialized to avoid having any stale data in the cache, like e.g.
partition tables or such.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
In case the card is removed, force-init the MMC to start the internal
machinery which deregisters and invalidate the MMC device.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Current CBFS component type list is incomplete. Add missing ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there are 2 macros that are named as CBFS_COMPONENT_xxx.
Change them to CBFS_TYPE_xxx for consistency.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
In case SYS_I2C or DM_I2C are defined, then the "i2c " prefix
of the "i2c crc32" command is missing.
This patch addresses this, so that users can't get confused
by the "crc32" command.
Without the patch we get
=> i2c help
i2c - I2C sub-system
Usage:
i2c bus [muxtype:muxaddr:muxchannel] - show I2C bus info
crc32 chip address[.0, .1, .2] count - compute CRC32 checksum
i2c dev [dev] - show or set current I2C bus
[...]
With the patch we get
=> i2c help
i2c - I2C sub-system
Usage:
i2c bus [muxtype:muxaddr:muxchannel] - show I2C bus info
i2c crc32 chip address[.0, .1, .2] count - compute CRC32 checksum
i2c dev [dev] - show or set current I2C bus
...
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The implementation of the EEPROM commands does not support the DM I2C API.
Prevent compilation breakage by not enabling it if the non-DM API is not
available (if DM_I2C is used without DM_I2C_COMPAT)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Hi,
setting active menuitem currently can be outside of menu which results in invisible selection
attached Patch fixes this
regards Frank
>From 1d9c4cb8b3e2dd9b0a7a6a2d4a21684d0a099dbf Mon Sep 17 00:00:00 2001
From: Frank Wunderlich <frank-w@public-files.de>
Date: Sun, 2 Dec 2018 11:23:53 +0100
Subject: [PATCH] ensure active menuitem is inside menu
if active menuitem is defined via environment var it can be outside the menu (>=menuitem-count)
this patch resets this definition back to 0
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Allow to display BMP at the middle of the screen.
'm' means "middle" as it is done for the splashscreen variable:
splashpos=m,m
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add common clear screen command for configurations
CONFIG_DM_VIDEO, CONFIG_LCD and CONFIG_CFB_CONSOLE.
Remove the existing cls command implementation from
lcd.c code and activate the command for all boards
enabling CONFIG_LCD for compatibility reasons.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Patrick.Delaunay <patrick.delaunay@free.fr>
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
When copying the device we must ensure that the copy does not fall into a
memory area reserved by the same.
So let's change the sequence: first create memory reservations and then
copy the device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The sandbox is using a virtual address space which is neither the physical
address space of the operating system nor the virtual address space in
which Linux aplications live. The addresses used insided the flattened
device tree use this sandbox virtual address space. The EFI subsystem uses
the virtual address space of the operating system and this is where the fdt
is stored.
Fix all incorrect addresses for the fdt in cmd/bootefi.cmd.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When allocating EFI memory pages the size in bytes has to be converted to
pages.
Provide a macro efi_size_in_pages() for this conversion.
Use it in the EFI subsystem and correct related comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This function can be used from do_bootefi_exec() so that we use mostly the
same code for a normal EFI application and an EFI test.
Rename the function and use it in both places.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There is still duplicated code in efi_loader for tests and normal
operation.
Add a new bootefi_run_prepare() function which holds common code used to
set up U-Boot to run EFI code. Make use of this from the existing
bootefi_test_prepare() function, as well as do_bootefi_exec().
Also shorten a few variable names.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The functions in bootefi are very long because they mix high-level code
and control with the low-level implementation. To help with this, create
functions which handle preparing for running the test and cleaning up
afterwards.
Also shorten the awfully long variable names here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present a few error conditions are not checked. Before refactoring
this code, add some basic checks. Note that this code still leaks memory
in the event of error. This will be tackled after the refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The "Devicetree Specification 0.2" does not prescribe that memory
reservations must be EFI page aligned. So let's not make such an
assumption in our code.
Do not carve out the pages for the device tree. This memory area is
already marked as EFI_RUNTIME_SERVICES_DATA.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In copy_fdt() we allocate EFI pages for the fdt plus extra 12 KiB as
EFI_RUNTIME_SERVICES_DATA. Afterwards in efi_install_fdt() we overwrite
part of this memory allocation by marking it as EFI_BOOT_SERVICES_DATA.
Remove the code marking the fdt as EFI_BOOT_SERVICES_DATA.
Cf. commit 17ff6f02f5 ("efi_loader: store DT in EFI_RUNTIME_SERVICES_DATA
memory")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Factor out efi_set_bootdev() and extract efi_dp_from_name().
This function will be used to set a boot device in efishell command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rename the component parent of some EFI objects to header. This avoids
misunderstandings.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
All our handles point to a struct efi_object. So let's define the
efi_handle_t accordingly. This helps us to discover coding errors much
more easily. This becomes evident by the corrections to the usage of
handles in this patch.
Rename variable image_handle to image_obj where applicable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present many TPM calls assume there is only one TPM in the system and
look up this TPM themselves. This is inconsistent with driver model, which
expects all driver methods to have a device parameter. Update the code to
correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
store fdt header member with name <member> in U-Boot
Environment variable with name <var>.
for example to get the total length of the fdt and store
it in filesize, call:
fdt header get filesize totalsize
For membernames look into fdt header definition at
scripts/dtc/libfdt/libfdt.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- spi_init_f
- spi_init_r
- spi_read
- spi_write
these spi calls are exclusively for mpc8xx, but
the relevant driver is not available so remove it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
with this patch the selected Entry in bootmenu can be set by
environment-var bootmenu_default=<number>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
There is some basic informaton that SPL normally wants to pass through to
U-Boot, such as the SDRAM size and bank information.
Mkae use of the new bloblist structure for this. Add a new 'handoff' blob
which is set up in SPL and passed to U-Boot proper. Also adda test for
sandbox_spl that checks that this works correctly and a new 'sb' command
to show the information passed from SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The old 'sb' command was deprecated in 2015 and replaced with 'host'. It
is useful to be able to access some internal sandbox state, particularly
for testing.
Resurrect the old command and provide a way to print some basic state
information (currently just the arguments to sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
The old 'sb' command was deprecated in 2015 and replaced with 'host'.
Remove the remaining users and the command, so that the name is available
for other purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Its only called from this file, so make it static. While at it, remove
some occurances of multiple blank lines as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch fixes the address information of fdt.
wrong case:
=> fdt addr 0x48000000
=> fdt move 0x48000000 0x41000000 0xa000
=> fdt addr
The address of the fdt is 48000000
Active address in this case is 0x41000000.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add new option to 'adc' command to do a single scan of:
- some channel(s), using mask argument
- all channels available on an ADC device (when optional mask is omitted).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use newly introduced adc_raw_to_uV() API to print conversion result
both as raw value and micro-volts by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enhance adc info command to report also the channel mask.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinmux command allows to :
- list all pin-controllers available on platforms
- select a pin-controller
- display the muxing of all pins of the current pin-controller
or all pin-controllers depending of given options
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
cmd: pinmux: Fix pinmux command
if "pinmux status" command is used without having
set dev using "pinmux dev", print pinmux usage
Reviewed-by: Simon Glass <sjg@chromium.org>
Display all digits on 64bit systems. Currently we print only the lower
32 bits. Examples of values that can exceed 32 bits are the size and start of
memory banks.
For fdt_blob use the same output method as for other values. This avoids
misalignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add 'virtio' command in U-Boot command line.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.
Update all DM BLK drivers to adopt this change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit c58fb2cdb3 ("cmd: ubi: clean the partition handling")
introduced a call to mtd_probe_devices() in the ubi_attach() path
and this function takes care of parsing mtdparts/mtdids and
creating/registering the associated mtd partitions.
The mtdparts_init() call in the ubi_detach() path is not only
unnecessary but can sometimes print error messages even when things
work properly (that's the case with SPI NAND devices that have not
been probed with 'mtd list'), which is misleading.
Remove this call to mtdparts_init() and drop the dependency on
CMD_MTDPARTS.
Fixes: c58fb2cdb3 ("cmd: ubi: clean the partition handling")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
gwventana configs are relying on CMD_UBI to select CMD_MTDPARTS,
which is then making {MTDIDS,MTDPARTS}_DEFAULT options available.
We are about to remove the 'select CMD_MTDPARTS' statement in the
CMD_UBI entry, but if we do that without first making sure
{MTDIDS,MTDPARTS}_DEFAULT are visible, we end up with a build
failure when building gwventana configs.
Address that by adding a depends on MTD_PARTITIONS to
{MTDIDS,MTDPARTS}_DEFAULT which does the trick since CMD_UBI selects
MTD_UBI which in turn selects MTD_PARTITIONS.
We also get rid of the depends on CMD_MTD, since CMD_MTD also selects
MTD_PARTITIONS.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This line is no more needed and can be removed.
Only CONFIG_CMD_SOURCE is defined in Kconfig and
used in defconfig files.
CONFIG_SOURCE if not defined in source code and
"config SOURCE" is not present in any Kconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Currently the base is 3 fix it 10 so that IDs follow decimal system.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvulta@ti.com>
All mii operations require a valid PHY address except the 'device'
command, which expects the PHY name rather than the address.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A few bug fixes for the 2018.11 release:
- Fix block seeking on 32bit
- Fix execution with DEBUG set
- Fix a few Coverity found bugs
- Fix warnings
Heinrich Schuchardt (13):
efi_loader: fix relocation on x86_64
efi_loader: correct signature of GetPosition, SetPosition
efi_loader: execute efi_save_gd() first
efi_loader: efi_allocate_pool(EFI_ALLOCATE_ANY_PAGES, ...)
efi_loader: error handling in read_console()
efi_loader: return type efi_console_register()
efi_loader: superfluous statement in is_dir()
efi_loader: memory leak in efi_set_variable()
efi_loader: remove lcd.h from efi_net.c
arm: do not include efi_loader.h twice
efi_loader: fix typo in efi_boottime.c
efi_selftest: creating new handle in controller test
efi_loader: efi_dp_get_next_instance() superfluous statement
Tom Rini (2):
efi_loader: Fix warning in efi_load_image()
fs: fat: Fix warning in normalize_longname()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CIpq
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-2018.11' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-10-17
A few bug fixes for the 2018.11 release:
- Fix block seeking on 32bit
- Fix execution with DEBUG set
- Fix a few Coverity found bugs
- Fix warnings
Heinrich Schuchardt (13):
efi_loader: fix relocation on x86_64
efi_loader: correct signature of GetPosition, SetPosition
efi_loader: execute efi_save_gd() first
efi_loader: efi_allocate_pool(EFI_ALLOCATE_ANY_PAGES, ...)
efi_loader: error handling in read_console()
efi_loader: return type efi_console_register()
efi_loader: superfluous statement in is_dir()
efi_loader: memory leak in efi_set_variable()
efi_loader: remove lcd.h from efi_net.c
arm: do not include efi_loader.h twice
efi_loader: fix typo in efi_boottime.c
efi_selftest: creating new handle in controller test
efi_loader: efi_dp_get_next_instance() superfluous statement
Tom Rini (2):
efi_loader: Fix warning in efi_load_image()
fs: fat: Fix warning in normalize_longname()
If DEBUG is defined we may be calling EFI_CALL already during the
initialization of the EFI subsystem. We must make sure efi_save_gd() has
already been called at that moment.
Anyway it is better to have this call in one location instead of three.
This fixes an illegal memory access occurring since 4e6b5d6503
("efi_loader: create root node") with DEBUG = 1.
Fixes: 4e6b5d6503 ("efi_loader: create root node")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Sandbox SPL/TPL support
Various dm-related improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
/b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
=Bfjm
-----END PGP SIGNATURE-----
Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
When updating the board FDT, some of the operations
are performed by ft_board_setup_ex() and should be
executed also by the fdt command.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present the mtrr functions disable the cache before making changes and
enable it again afterwards. This is fine in U-Boot, but does not work if
running in CAR (such as we are in SPL).
Update the functions so that the caller can request that caches be left
alone.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file has changed quite a bit in the last 5 years as the capabilities
of the ECs have grown. Sync it up with the copy in coreboot commit
b9141f2215.
The only change is the addition of EC_VBNV_BLOCK_SIZE_V2. This is needed
because U-Boot uses the new v2 vboot API and this is not currently fully
supported by Chromium OS firmware.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are needed for the 2018 version of Chromium OS vboot. Add an
implementation for TPM v1, with v2 to come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we pass around a private pointer to specify the cros_ec device.
With driver model it makes more sense to pass the device. Update the code
to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way in configuration files (exlinux.conf for sysboot command)
to select a specific FIT configuration. The configuration is selected
with a string added after the FIT filename in the label "KERNEL" or
"LINUX", using the same format than bootm command:
KERNEL [Filename]#<conf>[#<extra-conf[#...]]
This configuration string, beginning by '#', is directly appended
to bootm argument 1 after <kernel_addr_r>.
bootm [<kernel_addr_r>]#<conf>[#<extra-conf[#...]]
see doc/uImage.FIT/command_syntax_extensions.txt for details
Example :
KERNEL /fit.itb#cfg1
KERNEL /fit.itb#cfg2
Configuration can be use also for overlay management :
KERNEL /fit.itb#cfg1#dtbo1#dtbo3
see doc/uImage.FIT/overlay-fdt-boot.txt for details
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Prior to this patch was do_avb_write_rb() reading supplied rb_idx as a
hexadecimal number while do_avb_read_rb() printed the read out rb_idx as
decimal number. For consistency change do_avb_read_rb() to print rb_idx
as a hexadecimal number too.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'mtdparts' command is not needed anymore. While the environment
variable is still valid (and useful, along with the 'mtdids' one), the
command has been replaced by 'mtd' which is much more close to the MTD
stack and do not add its own specific glue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI should not mess with MTD partitions, now that the partitions are
handled in a clean way, clean the ubi command and avoid using this
uneeded extra-glue to reference the devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add trivial implementation of the clk dump in case DM is enabled.
This implementation just iterates over all the clock registered
with the CLK uclass and prints their rate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Previously poweroff was located under boot. It seems to make more
sense to have it located under the Device access commands.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add basic command for bus information and read for onewire
bus using Dallas 1-Wire protocol.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
cmd_ubifs_mount() function would be called directly instead of
involving whole command machinery for mounting ubifs in
generic firmware loader, so some checking codes need to be factored out
into cmd_ubifs_mount() without breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
cmd_ubifs_umount() function would be called directly instead of involving
whole command machinery in generic firmware loader, so checking on
ubifs_initialized status need to be done in cmd_ubifs_umount() without
breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix conflicting type error in cmd/ubi.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ZuJG
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'conitrace' command prints the codes received from the console input as
hexadecimal numbers.
This developer utility is useful for testing the handling of special keys
by keyboard drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Create the handle of loaded images and the EFI_LOADED_IMAGE_PROTOCOL
inside efi_setup_loaded_image(). Do not use local variables.
Currently we expect the loaded image handle to point to the loaded image
protocol. Additionally we have appended private fields to the protocol.
With the patch the handle points to a loaded image object and the private
fields are added here. This matches how we handle the net and the gop
object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running in EL3 mode on AArch64, we have to first drop to EL2
to execute a UEFI payload. When dropping down, the arguments to
the entry point have to stay identical to the ones for normal entry
though.
In commit ea54ad5928 ("efi_loader: pass handle of loaded image")
we incorrectly changed that logic and had the el3 entry path diverge.
Fix it up by syncing it back to what it's supposed to be.
Fixes: ea54ad5928 ("efi_loader: pass handle of loaded image")
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Currently we assign a lot of protocols to loaded images though
these protocols are not related to them. Instead they should be
installed on a separate handle. Via the device path it is the
parent to the devices like the network adapter.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_set_bootdev() may be called repeatedly.
Free the memory allocated for device paths in previous calls.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Do not use a local variable for the handle backing the memory device path.
Adjust relate comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, a new command, fatrm, is added so as to delete a file
or directory.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, a new command, fatmkdir, is added.
Please note that, as there is no notion of "current directory" on u-boot,
a directory name specified must contains an absolute directory path as
a parent directory. Otherwise, "/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, fatwrite command is extended so as to accept an additional
parameter of file offset.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The number of bytes in an utf-8 string is an upper limit for the number of
words in the equivalent utf-16 string. In so far the inumbant coding works
correctly. For non-ASCII characters the utf-16 string is shorter. With the
patch only the necessary buffer size is allocated for the load options.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present this function takes a pointer as its argument, then passes this
to efi_allocate_pages(), which actually takes an address. It uses casts,
which are not supported on sandbox.
Also the function calculates the FDT size rounded up to the neared EFI
page size, then its caller recalculates the size and adds a bit more to
it.
This function is much better written as something that works with
addresses only, and returns both the address and the size of the relocated
FDT.
Also, copy_fdt() returns NULL on error, but really should propagate the
error from efi_allocate_pages(). To do this it needs to return an
efi_status_t, not a void *.
Update the code in this way, so that it is easier to follow, and also
supports sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Sandbox only has 128MB of memory so we cannot relocate the device tree up
to start at 128MB. Use 127MB instead, which should be safe.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
All U-Boot users must define the mtdparts environment variable with:
setenv mtdparts mtdparts=...
While this may ease the partition declaration job to be passed to
Linux, this is a pure software limitation and forcing this prefix is a
complete non-sense. Let the user to declare manually the mtdparts
variable without the prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Let spi-nand devices be recognized by mtdparts. This is superfluous
but a full mtdparts rework would be very time-consuming.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Switch blocks for deriving size naturally use fallthrough between
'case' statements. Make it explicit.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
These definitions are simply not used and are misleading because similar
definitions exist in jffs2/load_kernel.h and are used widely to define
MTD device types (which is, by the way, totally redundant with what the
MTD core does). Remove these definitions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Exclude mvebu commands from SPL builds
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
There are ways how to call fpga loadmk
1. Full command
fpga loadmk [dev] [address]
2. Dev setup via variable
set fpga [dev]
fpga loadmk [address]
3. Address setup via variable
set fpgadata [address]
fpga loadmk [dev]
4. Dev and address setup via variables
set fpga [dev]
set fpgadata [address]
fpga loadmk
Before this patch only cases 1 and 3 are working but the part of code
was trying to support also cases 2 and 4.
This patch is adding support for cases 2 and 4 to have all of
combinations supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert loadmk command to fpga subcommands. Not all combinations are
working but they have never worked properly. This will be fixed later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Separate dump, load, loadb, loadp and loadbp commands to separate
functions to make it clear how they are called and what parameters they
need.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move fpga info to U_BOOT_CMD_MKENT subcommand.
Also use strtol instead of simple_strtoul. The reason is that if -1 is
passed (or fpga info without "fpga" variable) the list of all fpgas is
shown.
This functionality is in the fpga core but it couldn't be performed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create command wrapper to clean fpga subcommands.
The function logic is taken from cmd_dm.c
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to check parameters in separate switch. Check them
directly when they are read. Also there is no reason to check loadmk
case separately because fpga_data address must be non zero too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Parameter checking is dead code because all the time there must be all
params assigned. If they are not assigned there is no 9th parameters
passed and checking before return CMD_RET_USAGE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to check parameters in separate switch before main
one. This patch is simplifying error path and checking parameters right
after assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Incorrect command is already handled and FPGA_NONE should be used only
one. In case of error CMD_RET_USAGE can be returned directly without any
addition logic around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move fpga_get_op() to top of file to remove local function declaration
and also remove useless retyping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clean fpga_get_op() error handling by moving checking/print to do_fpga.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch applied in 2010
"cmd_fpga: cleanup help and check parameters"
(sha1: a790b5b2326be9d7c9ad9e3d9b51a8bfabc62d07"
was adding this checking
+ if (dev == FPGA_INVALID_DEVICE) {
+ puts("FPGA device not specified\n");
+ op = FPGA_NONE;
+ }
which simply broke one command flow which was
setenv fpga <dev>
fpga loadmk <addr> // legacy image
fpga loadmk <addr>:<fit_image_name> //fit image
Also this sequence for FIT image is completely broken
setenv fpga <dev>
setenv fpgadata <addr>:<fit_image_name>
fpga loadmk
(Note: For legacy images this is working fine).
even from code I don't think this has ever worked properly
for fit image (dev = FPGA_INVALID_DEVICE should be rejected
by fpga core). Fit image support was in 2008 added by:
"[new uImage] Add new uImage fromat support to fpga command"
(sha1: c28c4d193d)
Just a summary of these facts that none found this for pretty long time
it shouldn't be a problem to remove this flow (without fpga dev)
completely to simplify the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use Macro instead of hard code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is not preferred to put SUNXI-specific code in the common place.
Change it to 'imply' property of ARCH_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Currently when using bootelf to load an image on Arm, several warnings
such as the following appear in the console:
CACHE: Misaligned operation at range [87800000, 8783c5e0]
CACHE: Misaligned operation at range [8783c5e0, 8784b3e0]
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Reword commit message to include the info after the --- which
included the Signed-off-by line, and change ' at ' to '@']
Signed-off-by: Tom Rini <trini@konsulko.com>
A few fixes for 2018.09. Most noticable are:
- unbreak x86 target (-fdata-section fallout)
- fix undefined behavior in a few corner cases
- make Jetson TX1 boot again
- RTS fixes
- implement reset for simple output
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zi4z
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-2018.09' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-08-21
A few fixes for 2018.09. Most noticable are:
- unbreak x86 target (-fdata-section fallout)
- fix undefined behavior in a few corner cases
- make Jetson TX1 boot again
- RTS fixes
- implement reset for simple output
In some cases it can be useful to be able to bind a device to a driver from
the command line.
The obvious example is for versatile devices such as USB gadget.
Another use case is when the devices are not yet ready at startup and
require some setup before the drivers are bound (ex: FPGA which bitsream is
fetched from a mass storage or ethernet)
usage example:
bind usb_dev_generic 0 usb_ether
unbind usb_dev_generic 0 usb_ether
or
unbind eth 1
bind /ocp/omap_dwc3@48380000/usb@48390000 usb_ether
unbind /ocp/omap_dwc3@48380000/usb@48390000
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In case when user provides '-' as USB controller index, like this:
=> fastboot -
data abort occurs in strcmp() function in do_fastboot(), here:
if (!strcmp(argv[1], "udp"))
(tested on BeagleBone Black).
That's because argv[1] is NULL when user types in the '-', and null
pointer dereference occurs in strcmp() (which is ok according to C
standard specification). So we must validate user input to prevent such
behavior.
While at it, check also the result of strtoul() function and handle
error cases properly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Fix cppcheck complaint:
[cmd/efi.c:173]: (style) Clarify calculation precedence for '&' and '?'.
Fixes: f1a0bafb58 ("efi: Add a command to display the memory map")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
With this update, the memory attributes are in sync with Linux
kernel v4.18-rc4. They also match page 190 of UEFI 2.7 spec [1].
[1] http://www.uefi.org/sites/default/files/resources/UEFI_Spec_2_7.pdf
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Starting with commit 867a6ac86d ("efi: Add start-up library code"),
sparse constantly complains about truncated constant value in efi.h:
include/efi.h:176:35: warning: cast truncates bits from constant value (8000000000000000 becomes 0)
This can get quite noisy, preventing real issues to be noticed:
$ make defconfig
*** Default configuration is based on 'sandbox_defconfig'
$ make C=2 -j12 2>&1 | grep truncates | wc -l
441
After the patch is applied:
$ make C=2 -j12 2>&1 | grep truncates | wc -l
0
$ sparse --version
v0.5.2
Following the suggestion of Heinrich Schuchardt, instead of only
fixing the root-cause, I replaced the whole enum of _SHIFT values
by ULL defines. This matches both the UEFI 2.7 spec and the Linux
kernel implementation.
Some ELF size comparison before and after the patch (gcc 7.3.0):
efi-x86_payload64_defconfig:
text data bss dec hex filename
407174 29432 278676 715282 aea12 u-boot.old
407152 29464 278676 715292 aea1c u-boot.new
-22 +32 0 +10
efi-x86_payload32_defconfig:
text data bss dec hex filename
447075 30308 280076 757459 b8ed3 u-boot.old
447053 30340 280076 757469 b8edd u-boot.new
-22 +32 0 +10
Fixes: 867a6ac86d ("efi: Add start-up library code")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
dtimg command allows user to work with Android DTB/DTBO image format.
Such as, getting the address of desired DTB/DTBO file, printing the dump
of the image in U-Boot shell, etc.
This command is needed to provide Android boot with new Android DT image
format further.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This update adds PPC64 ELF V1 ABI support to bootelf for both the
program header and section header options. Elf64 support was already
present for the program header option, but it was not handling the
PPC64 ELF V1 ABI case. For the PPC64 ELF V1 ABI, the e_entry field of
the elf header must be treated as function descriptor pointer instead
of a function address. The first doubleword of the function descriptor
is the function's entry address.
Signed-off-by: Rob Bracero <robbracero@gmail.com>
[trini: Fix whitespace issues]
Signed-off-by: Tom Rini <trini@konsulko.com>
sata_probe returns 1 for failure, so don't checkout for < 0
fixes: f19f1ecb60 dm: sata: Support driver model with the 'sata' command
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Trivial Kconfig cleanup. Use tabs instead of spaces and every Kconfig
entry should be separated by newline.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
While there is probably no reason to do so in a real life situation, it
will allow to compile test both stacks with the same sandbox defconfig.
As we cannot define two 'tpm' commands at the same time, the command for
TPM v1 is still called 'tpm' and the one for TPM v2 'tpm2'. While this
is the exact command name that must be written into eg. test files, any
user already using the TPM v2 stack can continue to do so by just writing
'tpm' because as long as TPM v1 support is not compiled, U-Boot prompt
will search for the closest command named after 'tpm'.
The command set can also be changed at runtime (not supported yet, but
ready to be), but as one can compile only either one stack or the other,
there is still one spot in the code where conditionals are used: to
retrieve the v1 or v2 command set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: In sandbox_tpm2_fill_buf() use NULL not \0 to ensure NULL
terminated string due to LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of depending on a env callback for bootfile, read it explicitly.
We do this because the bootfile can be specified on the command line and
if it is, we will overwrite the internal variable. If a netboot_common()
is called again with no bootfile parameter, we want to use the one in
the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
On 64bit platforms we would otherwise see:
../cmd/ubi.c: In function 'ubi_volume_read':
../cmd/ubi.c:359:16: warning: format '%u' expects argument of type 'unsigned int', but argument 2 has type 'size_t {aka long unsigned int}' [-Wformat=]
Fixes: 68c7025d99 ("cmd: ubi: print load size after establishing volume size")
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove unused function efi_get_time_init().
Initialization of the RTC has to be done in board bring up not in the EFI
subsystem.
There is no RTC device in the UEFI spec. The RTC is only accessed through
the runtime services.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
For the boot and runtime services tables and for the system table the
crc32 has to be set in the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This function currently returns an error code, but never uses it. There is
no function comment so it is not obvious why. Presuambly the error is not
important.
Update the function to explain its purpose and why it ignores the error.
Drop the useful error return value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is a bit confusing at present since it adds 4KB to the pointer, then
rounds it up. It looks like a bug, but is not.
Move the 4KB addition into a separate statement and expand the comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The bootefi command gets a few addresses as values passed in. In sandbox,
these values are in U-Boot address space, so we need to make sure we
explicitly call map_sysmem() on them to be able to access them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Multiple EFI binaries may be executed in sequence. So if we already
are in non-secure mode after running the first one we should skip
the switching code since it no longer works once we're non-secure.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If desired (and possible) switch into HYP mode or non-secure SVC mode
before calling the entry point of an EFI application. This allows
U-Boot to provide a usable PSCI implementation and makes it possible
to boot kernels into hypervisor mode using an EFI bootloader.
Based on diffs from Heinrich Schuchardt and Alexander Graf.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
[agraf: Fix indentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
In the case that there was no name defined for a partition the
code assumes that name_len is 22 and therefore allocates exactly
that space for a dummy name. But the function sprintf() first
resolves "0x%08llx@0x%08llx" to a string that is longer than 22
bytes. This leads to a buffer overflow. The replacement function
snprintf() limits the copied bytes to name_len and therefore
avoids the buffer overflow.
Signed-off-by: Kay Potthoff <Kay.Potthoff@microsys.de>
While the `env export` can take as parameters variables to be exported,
`env import` does not have such a mechanism of variable selection.
Let's add the ability to add parameters at the end of the command for
variables to be imported.
Every env variable from the env to be imported passed by parameter to
this command will override the value of the variable in the current env.
If a variable exists in the current env but not in the imported env, if
this variable is passed as a parameter to env import, the variable will
be unset ONLY if the -d option is passed to env import, otherwise the
current value of the variable is kept.
If a variable exists in the imported env, the variable in the current
env will be set to the value of the one from the imported env.
All the remaining variables are left untouched.
As the size parameter of env import is positional but optional, let's
add the possibility to use the sentinel '-' for when we don't want to
give the size parameter (when the env is '\0' terminated) but we pass a
list of variables at the end of the command.
env import addr
env import addr -
env import addr size
env import addr - foo1 foo2
env import addr size foo1 foo2
are all valid.
env import -c addr
env import -c addr -
env import -c addr - foo1 foo2
are all invalid because they don't pass the size parameter required for
checking, while the following are valid.
env import addr size
env import addr size foo1 foo2
Nothing's changed for the other parameters or the overall behaviour.
One of its use case could be to load a secure environment from the
signed U-Boot binary and load only a handful of variables from an
other, unsecure, environment without completely losing control of
U-Boot.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The error message should start with `## Error: ` so that it's easily
detectable by tests without needing to have a complex regexp for
matching all possible error message patterns.
Let's add the `## Error: ` prefix to the error messages since it's the
one already in use.
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
