Commit graph

53 commits

Author SHA1 Message Date
Philippe Reynes
353496b756 gpio: bcm6345: allow this driver on ARCH_BCM63158
This IP is also used on some arm SoC, so we allow
to use this driver on arch bcm63158.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12 17:32:51 +02:00
Philippe Reynes
14c9bd46e5 gpio: bcm6345: allow this driver on ARCH_BCM6858
This IP is also used on some arm SoC, so we allow
to use this driver on arch bcm6858.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12 17:32:51 +02:00
Peng Fan
1610368234 gpio: introduce CONFIG_SPL_DM_PCA953X
Introduce CONFIG_SPL_DM_PCA953X for SPL usage.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28 20:35:47 +01:00
Lars Povlsen
ace9c103df mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-16 13:56:43 +01:00
Lars Povlsen
be8313feee mips: mscc_sgpio: Add the MSCC serial GPIO device (SIO)
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.

By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.

This adds the base driver.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
2019-01-16 13:56:43 +01:00
Gregory CLEMENT
02aea4da1d gpio: mscc-bitbang-spi: Add a simple gpio driver for bitbgang spi
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
flash directly in memory. However, for writing in the flash the
communication has to be done by software.

Each of the signal used for the SPI are exposed in a single register. In
order to be able to use the soft-spi driver, the management of this pin
is done through this simple gpio driver.

Even if the main purpose of this driver is to be used by soft-spi, it can
still be used as a normal gpio driver but with limitation: for example
the first pin can't be used as output.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-12-19 15:23:01 +01:00
Stefan Roese
4751e5595e gpio: Add MT7621 GPIO support
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned']
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-11-18 16:02:22 +01:00
Adam Ford
5d653afc17 Convert CONFIG_DA8XX_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_DA8XX_GPIO

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Michal Simek
4a69366967 microblaze: Convert generic platform to DM gpio
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
	compatible = "gpio-restart";
	gpios = <&reset_gpio 0 0 0>;
	/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Hannes Schmelzer
8fd05fccc8 drivers/gpio/mxc: fix MXC GPIO name in KConfig
The naming with "UART" is obviously wrong, we fix this here.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-06-18 16:50:07 +02:00
Patrick Delaunay
2514c2d0e6 arm: stm32: add new architecture for STM32MP family
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:21 -04:00
Vipul Kumar
71d5a14204 microblaze: Added Kconfig support for CONFIG_XILINX_GPIO
This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-01 15:43:45 +01:00
Adam Ford
8bbff6a70e Convert CONFIG_MXC_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_MXC_GPIO

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-02-08 10:17:16 -05:00
Mario Six
3c21683480 gpio: mpc8xxx: Rename Kconfig option, structures, and functions
Rename the Kconfig option, structures (and their members), as well as
functions of the mpc85xx driver to include mpc8xxx to reflect the more
generic usage.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-01-28 09:36:28 -05:00
Alexey Brodkin
d5fbcd57ed gpio/hsdk: Depend on DM_GPIO instead of simple DM
This driver really is DM GPIO one and so we need to have a correct
dependency, because DM alone doesn't provide required for CMD_GPIO
call and we're seeing build failures like this:
---------------------->8---------------------
cmd/built-in.o: In function 'do_gpio':
.../cmd/gpio.c:188: undefined reference to 'gpio_request'
...
---------------------->8---------------------

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-12-12 18:47:30 +03:00
Eugeniy Paltsev
3194c3cddf ARC: HSDK: introduce CREG GPIO driver
The HSDK can manage some pins via CREG registers block.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2017-11-24 19:37:56 +03:00
Marek Vasut
f5f6959444 gpio: rmobile: Add Renesas RCar GPIO driver
Add GPIO driver for the Renesas RCar SoCs . The driver currently supports
only the RCar Gen3 R8A7795 and R8A7796 SoCs, but is easily extensible for
the other RCar SoCs as well.

This driver is meant to replace the pinmux part of SH_GPIO_PFC driver.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-28 06:54:06 +09:00
Simon Glass
90d99e5936 Convert CONFIG_CMD_TCA642X to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_TCA642X

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:42:00 -04:00
Simon Glass
0091362ce5 Convert CONFIG_CMD_PCA953X to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_PCA953X

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:50 -04:00
Bin Meng
724368928c x86: Convert INTEL_ICH6_GPIO to Kconfig
This converts Intel ICH6 GPIO driver to Kconfig, and add it to the
imply list of platform drivers.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-01 20:17:02 +08:00
Tom Rini
29cb2b3b90 gpio: Move OMAP_GPIO to Kconfig
This driver is used often enough such that we want to have this enabled
by default on any ARCH_OMAP2PLUS board, and this only compiles on
ARCH_OMAP2PLUS due to required defines, so mark that as the depends.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:00 -04:00
Álvaro Fernández Rojas
e64bdb2fcf dm: gpio: add BCM6345 gpio driver
This driver is based on linux/arch/mips/bcm63xx/gpio.c, simplified to allow
defining one or two independent banks for each Broadcom SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Vikas Manocha
774171020b dm: gpio: Add driver for stm32f7 gpio controller
This patch adds gpio driver supporting driver model for stm32f7 gpio.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Christophe KERELLO <christophe.kerello@st.com>
[trini: Add depends on STM32]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-08 11:57:02 -04:00
Wenyou Yang
5a07a5f922 gpio: Kconfig: add CONFIG_AT91_GPIO option
The CONFIG_AT91_GPIO option is used to select AT91 PIO GPIO driver.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13 14:44:50 -06:00
Peng Fan
d665eb6114 gpio: Add Rapid GPIO2P driver for i.MX7ULP
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.

The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.

To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Wenyou Yang
ee3311db1c gpio: atmel_pio4: Rework to support DM & DT
Rework the driver to support driver model and device tree, and
support to regard the pio4 pinctrl device as a child of
atmel_pio4 device.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-15 22:58:03 +02:00
Vignesh R
5746b0df9c gpio: Add driver for TI PCF8575 I2C GPIO expander
TI's PCF8575 is a 16-bit I2C GPIO expander.The device features a
16-bit quasi-bidirectional I/O ports. Each quasi-bidirectional I/O can
be used as an input or output without the use of a data-direction
control signal. The I/Os should be high before being used as inputs.
Read the device documentation for more details[1].

This driver is based on pcf857x driver available in Linux v4.7 kernel.
It supports basic reading and writing of gpio pins.

[1] http://www.ti.com/lit/ds/symlink/pcf8575.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-08-08 13:32:53 -04:00
Tom Rini
cc749523ae Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2016-06-04 12:12:26 -04:00
mario.six@gdsys.cc
51781783c5 dm: gpio: Implement open drain for MPC85XX GPIO
This patch implements the open-drain setting feature for the MPC85XX
GPIO controller.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 22:14:12 -07:00
mario.six@gdsys.cc
07d31f8f98 dm: gpio: Add driver for MPC85XX GPIO controller
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).

Each GPIO bank is identified by its own entry in the device tree, i.e.

gpio-controller@fc00 {
      #gpio-cells = <2>;
      compatible = "fsl,pq3-gpio";
      reg = <0xfc00 0x100>
}

By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).

The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.

The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 22:13:24 -07:00
Stephen Warren
074a1fdd27 gpio: add Tegra186 GPIO driver
Tegra186's GPIO controller register layout is significantly different from
previous chips, so add a new driver for it. In fact, there are two
different GPIO controllers in Tegra186 that share a similar register
layout, but very different port mapping. This driver covers both.

The DT binding is already present in the Linux kernel (in linux-next via
the Tegra tree so far).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # v1
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-31 09:54:24 -07:00
Stephen Warren
601800be22 ARM: tegra: convert CONFIG_TEGRA_GPIO to Kconfig
Future chips will contain different GPIO HW. This change will enable
future SoC support to select the appropriate GPIO driver for their HW,
in a future-looking fashion, using Kconfig.

TEGRA_GPIO is not simply selected by TEGRA_COMMON (even though all
current Tegra chips used this GPIO HW) to simplify the later addition
of support for Tegra SoCs that use different GPIO HW.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-31 09:53:57 -07:00
Peng Fan
9300f711ba dm: gpio: introduce 74x164 driver
Introduce driver to support "fairchild,74hc595" devices.
1. Take linux drivers/drivers/gpio/gpio-74x164.c as reference.
2. Following the naming used in Linux driver with gen_7x164 as the prefix.
3. Enable CONFIG_DM_74X164 to use this driver.
4. Follow Documentation/devicetree/bindings/gpio/gpio-74x164.txt to add device
   nodes
5. Tested on i.MX6 UltraLite with 74LV595 using gpio command and oscillograph.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Peng Fan
037734393e dm: gpio: pca953x: introduce driver model support for pca953x
Introduce a new driver that supports driver model for pca953x.
The pca953x chips are used as I2C I/O expanders.
This driver is designed to support the following chips:
"
4 bits: pca9536, pca9537
8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554,
        pca9556, pca9557, pca9574, tca6408, xra1202
16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575,
         tca6416
24 bits: tca6424
40 bits: pca9505, pca9698
"
But for now this driver only supports max 24 bits and pca953x compatible
chips. pca957x compatible chips are not supported now.
These can be addressed when we need to add such support for the different
chips.
This driver has been tested on i.MX6 SoloX Sabreauto board with max7310
i2c expander using gpio command as following:

=>gpio status -a
Bank gpio@30_:
gpio@30_0: input: 1 [ ]

=> dm tree:
 i2c         [   ]    |   |   `-- i2c@021a8000
 gpio        [   ]    |   |       |-- gpio@30
 gpio        [   ]    |   |       `-- gpio@32

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Andrea Scian <andrea.scian@dave.eu>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com> #on ZynqMP zcu102
2016-05-17 09:54:43 -06:00
Siva Durga Prasad Paladugu
251ab06d26 zynqmp: Kconfig: Enable ZYNQ_GPIO for ZynqMP
Enable ZYNQ_GPIO for ZynqMP using Kconfig. It enables the GPIO
driver support for ZynqMP.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:06 +02:00
Siva Durga Prasad Paladugu
2978ae23fa gpio: Kconfig: Enable Zynq GPIO driver using kconfig
Enable DM GPIO and ZYNQ GPIO using kconfig instead of the board
config file.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:06 +02:00
Mateusz Kulikowski
120800df72 gpio: Add support for Qualcomm PM8916 gpios
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:13 -04:00
Mateusz Kulikowski
81a87e1894 gpio: Add support for Qualcomm gpio controller
Add support for gpio controllers on Qualcomm Snapdragon devices.
This devices are usually called Top Level Mode Multiplexing in
Qualcomm documentation.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:07 -04:00
Stefan Roese
704d9a645e gpio: Add DM GPIO driver for Marvell MVEBU
This patch adds a DM GPIO driver for the Marvell MVEBU SoCs. There are
other non-DM drivers that might be used on these platforms. But this
patch creates a new DM driver. Which will be used by all Armada XP/38x
boards. Other MVEBU SoC (Kirkwood / Orion) may follow once they
support DM as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-03-24 09:44:39 +01:00
Simon Glass
64b179770f x86: broadwell: Add a GPIO driver
Add a GPIO driver for the GPIO peripheral found on broadwell devices.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17 10:27:26 +08:00
Masahiro Yamada
b9a66b63b4 gpio: uniphier: add driver for UniPhier GPIO controller
This GPIO controller device is used on UniPhier SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-02-29 03:50:15 +09:00
Purna Chandra Mandal
386d934e0b drivers: gpio: add driver for Microchip PIC32 GPIO controller.
In PIC32 GPIO controller is part of PIC32 pin controller.
PIC32 has ten independently programmable ports and each with multiple pins.
Each of these pins can be configured and used as GPIO, provided they
are not in use for other peripherals.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-02-01 22:14:00 +01:00
Wenyou Yang
2c62c56a86 gpio: atmel: Add the PIO4 driver support
The PIO4 is introduced from SAMA5D2, as a new version
for Atmel PIO controller.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2015-11-30 22:27:52 +01:00
Thomas Chou
88d5ecf4b9 nios2 : convert altera_pio to driver model
Convert altera_pio to driver model.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-10-23 07:37:03 +08:00
Simon Glass
1f8f7730a8 rockchip: gpio: Add rockchip GPIO driver
This supports RK3288 at present. It does not implement functions or support
for pull up/down.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-02 21:28:23 -06:00
Marek Vasut
e30a70c2d3 gpio: Add DW APB GPIO driver
Add driver for the DesignWare APB GPIO IP block.
This driver is DM capable and probes from DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
2015-08-23 11:56:20 +02:00
Masahiro Yamada
0b11dbf705 drivers: hierarchize drivers Kconfig menu
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu.  Use hierarchic menu for each category.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:47:44 -04:00
Bhuvanchandra DV
d348a943e7 dm: gpio: vf610: Add GPIO driver support
Add GPIO driver support to Freescale VF610

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
2015-06-08 08:41:54 +02:00
Simon Glass
d79c50af26 sandbox: Move GPIO CONFIGs to Kconfig
Move these over to Kconfig and tidy up.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:37 -06:00
Albert ARIBAUD \(3ADEV\)
606f704760 lpc32xx: add GPIO support
This driver only supports Driver Model, not legacy model.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:09 +02:00