Commit graph

94 commits

Author SHA1 Message Date
Adam Ford
81b564353d ARM: da850-evm: Disable SYS_MMCSD_RAW_MODE_USE_SECTOR
The da850-evm doesn't have the boot pins configured in a way
to make MMC/SD booting an option, and MMC/SD support is not
enabled in SPL.  Therefore, there is no need to support raw mode
mmc/sd support in SPL.

This patch disables CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-12-05 10:28:39 -05:00
Miquel Raynal
888f184abe mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD
Like in Linux, just use CONFIG_MTD to compile the MTD stack.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
1de770d544 mtd: rename CONFIG_MTD -> CONFIG_DM_MTD
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 23:04:10 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Tom Rini
0be2ecd486 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 17:58:06 -05:00
Tom Rini
665c35a764 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23 11:47:37 -04:00
Hannes Schmelzer
1ee774d209 Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:59:00 -04:00
Adam Ford
78f28773a5 Convert CONFIG_MX_CYCLIC to Kconfig
This converts the following to Kconfig:
   CONFIG_MX_CYCLIC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: David Lechner <david@lechnology.com>
2019-08-23 16:45:40 -04:00
Adam Ford
2ed45fd6ac ARM: da850-evm: Enable the USB PHY and MUSB Driver
This patch will enable the MUSB driver to support mass storage
devices connected to the OTG port in host mode.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-08 11:35:02 +02:00
Adam Ford
3cdecb341e ARM: da850-evm: Replace CMD_SF with CMD_MTD
This patch enables MTD and CMD_MTD and it works with SPI NOR,
so the older CMD_SF can be removed.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-31 13:08:07 -04:00
Adam Ford
ef97842b43 ARM: da850evm: Split MTDPARTS into SPL and u-boot
The MTDPARTS currently lists just u-boot.ais as 512k in size.
This works when loading the ais file via serial port, but if one
wanted to update just the u-boot portion, it's not really possible.
This patch splits the MTDPARTS into a 32k SPL partiion and a 480k
u-boot partition which allows u-boot.img to be burned to the u-boot
partition.  The remaining partitions are left with the same sizes
and offsets to not break backwards compatibility.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-31 13:08:07 -04:00
Bartosz Golaszewski
95cffd9906 davinci: da850-evm: enable driver model for NAND
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.

On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
2019-07-29 17:58:52 -04:00
Adam Ford
7f89cb29ef ARM: da850evm: Remove legacy OHCI referencs and unify platform
OHCI was added with DM_USB support, so there are a few unneeded
items in the header file that can be removed.  This also
unifies da850evm with NOR and NAND booting options so all have
OHCI support.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate da850_am18xxevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-27 13:36:53 -04:00
Bartosz Golaszewski
e809285d49 net: davinci_emac: convert to using the driver model
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2019-07-25 13:36:13 -05:00
Sekhar Nori
2a766db938 ARM: davinci: SPL: fix BSS initialization
U-Boot README recommends initializing SDRAM in board_init_f(). DA850
was doing it as part of board_init_r() (through call to spl_board_init()
which calls arch_cpu_init() which calls da850_ddr_setup())

This worked fine till commit 15b8c75058 ("davinci:
da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is full") moved
BSS to SDRAM.

Functions like mmc_initialize() called in board_init_r() assume BSS is
available. Since SDRAM was not initialized when arch/arm/lib/crt0.S tried
to initialize BSS to 0, BSS is not initialized correctly.

Fix this by simply calling arch_cpu_init() from board_init_f(). Also move
preloader_console_init() there to help debug issues with board_init_r().

With this spl_board_init() is no longer needed, we remove it.

Tested using MMC/SD boot on OMAP-L138 LCDK board.

Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
2019-06-05 12:14:02 -04:00
Adam Ford
612f6b223d ARM: da850evm: Enable block cache during SPL
There appears to be enough RAM to support cache in SPL.
This pach enables block cache in SPL.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-05-18 12:32:03 -04:00
Adam Ford
95468e6c9b ARM: da850evm: Enable da850-ohci USB host controller
The DA850 EVM has one USB 1.1 OHCI Host controller.  With the
host controller now support DM_USB, this patch enables
the respective functions for the da850evm.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-05-05 08:48:50 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Adam Ford
cd2d8245ac ARM: da850evm: Fix TI boot scripts for MMC
The da850evm include environment/ti/mmc.h and places
DEFAULT_MMC_TI_ARGS, defined int that file, in
CONFIG_EXTRA_ENV_SETTINGS.  This has been broken for some time
since neither CMD_PART nor CMD_UUID are available, so manually
changing the environmental variables was always required before
booting from MMC. With this patch, these scripts should work
again, and by default they point to mmc 0, partition 2, and
the dtb file exists in a /boot directory on partition 2.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-26 18:58:21 -04:00
Adam Ford
fd3c26f3f9 ARM: da850evm: Fix broken SPI Flash
A previous patch converted a bunch of settings for CONFIG_SF_DEFAULT
but it broke the SPI Flash which now prevents booting.  This patch
now correctly sets CONFIG_SF_DEFAULT_SPEED=30000000 to match what it
was before the conversion.

Fixes: 14453fbfad ("Convert CONFIG_SF_DEFAULT_* to Kconfig")

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-26 18:58:21 -04:00
Tom Rini
216800acf1 Merge branch 'master' of git://git.denx.de/u-boot-spi
Conflicts:
	arch/arm/dts/armada-385-amc.dts
	arch/arm/dts/armada-xp-theadorable.dts
	arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-14 00:03:06 -04:00
Adam Ford
f7c1d53605 ARM: davinci: da850evm: Enable SPL_OF_CONTROL without PLATDATA
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12 08:05:49 -04:00
Patrick Delaunay
b0cc1b846f dm: spi: Read default speed and mode values from DT
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")

In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.

DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.

But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 11:54:50 +05:30
Patrick Delaunay
abe66b1b5d Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:59 -04:00
Adam Ford
591353d011 ARM: da850evm: Increase Malloc Size
The SPI NOR frameware was recently updated, but they require a little
more memory that we had previosly allocated, so it stopped booting.
This patch doubles the size of CONFIG_SPL_SYS_MALLOC_F_LEN to 0x800.

Fixes: c4e8862308 ("mtd: spi: Switch to new SPI NOR framework")

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-19 08:55:43 -05:00
Tom Rini
1bac199e8c configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07 18:11:00 -05:00
Tom Rini
cbabe7f87f configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand.  This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.

Fixes: 86dfa556d9 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-14 10:53:27 -05:00
Tom Rini
4114a2614b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-13 19:44:53 -05:00
Jagan Teki
cb19c29398 board: da8xxevm: Add SPL DM for serial, spi
This patch add SPL DM support for da8xxevm boards
with SPL serial, SPI drivers supported via platdata.

Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
2018-10-10 11:53:55 +05:30
Adam Ford
5a5e55ba29 ARM: da850evm: Pinctrl for da850evm
The simple pin controller works for da850, so this patch enables
this to pin-mux the pins defined in the device tree for the da850evm.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29 08:07:27 -04:00
Adam Ford
5b3b429904 ARM: da850evm: Enable CMD_DM for da850evm
With DM enabled, this patch enables the 'dm' command to access
the dm tree, uclass and devres.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29 08:07:27 -04:00
Adam Ford
4aeb939e77 ARM: davinci: da850evm: Support DM_MMC
With the updated driver available to support DM_MMC, this patch
enables DM_MMC for da850evm.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:41:15 -04:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Adam Ford
c4fa049a12 ARM: da850evm: Enable SPL_SYS_MALLOC_SIMPLE
The SPL space is limited.  In order to try to enable DM in SPL,
we need more space. When combined wtih TINY_PRINTF, this reduces
the size of SPL by 6.5k

Original:

   text	   data	    bss	    dec	    hex	filename
  20760	   1216	     80	  22056	   5628	spl/u-boot-spl

Tiny Printf
   text	   data	    bss	    dec	    hex	filename
  17947	   1216	     80	  19243	   4b2b	spl/u-boot-spl

Malloc Simple + Tiny Printf
   text	   data	    bss	    dec	    hex	filename
  15187	    176	     28	  15391	   3c1f	spl/u-boot-spl

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-20 07:21:27 -04:00
Adam Ford
f09d831557 ARM: da850evm: Enable USE_TINY_PRINTF
The SPL space is limited.  In order to try to enable DM in SPL,
we need more space. This reduces the size of SPL by ~2.7K

before:
   text	   data	    bss	    dec	    hex	filename
  20760	   1216	     80	  22056	   5628	spl/u-boot-spl
after:
   text	   data	    bss	    dec	    hex	filename
  17947	   1216	     80	  19243	   4b2b	spl/u-boot-spl

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-20 07:21:27 -04:00
Adam Ford
391328dc30 configs: da850evm: Remove DM_I2C_COMPAT
Since using DM_I2C_COMPAT throws a warning during compilation,
and it isn't really needed any longer, so this patch removes
this feature and shrinks the code a bit.

from:
   text	   data	    bss	    dec	    hex	filename
 343326	  13388	 123448	 480162	  753a2	u-boot

to:
   text	   data	    bss	    dec	    hex	filename
 342924	  13380	 123440	 479744	  75200	u-boot

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-20 07:21:27 -04:00
Adam Ford
9f8cf76be2 Convert CONFIG_SYS_I2C_DAVINCI to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_DAVINCI

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-17 15:43:38 -04:00
Adam Ford
8ccf98b1cf Convert CONFIG_MISC_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17 13:04:00 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Adam Ford
5d653afc17 Convert CONFIG_DA8XX_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_DA8XX_GPIO

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
9c5b00973b Convert CONFIG_MTD_PARTITIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-22 19:20:17 -04:00
Adam Ford
8e51c0f254 dm: gpio: Add DM compatibility to GPIO driver for Davinci
This adds DM_GPIO support for the davinici GPIO driver with
DT support.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-18 14:43:12 -04:00
Tom Rini
358b6a20e4 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 11:57:37 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Tom Rini
34b3722e38 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-17 10:10:47 -04:00
Marek Vasut
555004381e spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
2018-04-11 13:22:00 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00