Commit graph

61 commits

Author SHA1 Message Date
Fabio Estevam
827f0a3f22 mx6sxsabresd: Enable DM_PCI
Enale DM_PCI support in order to avoid board removal from
the project.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09 15:05:24 +01:00
Tom Rini
052170c6a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 13:38:00 -05:00
Tom Rini
0cfccb5401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:18:38 -05:00
Miquel Raynal
63ea317245 mtd: ensure MTD is compiled when there is a SPI NOR flash using MTD
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Tom Rini
0be2ecd486 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 17:58:06 -05:00
Adam Ford
3f70bef1b8 Convert CONFIG_FSL_USDHC to Kconfig
This converts the following to Kconfig:
   CONFIG_FSL_USDHC

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-23 16:42:38 -04:00
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Patrick Delaunay
14453fbfad Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:53 -04:00
Vignesh R
6d82517836 configs: Don't use SPI_FLASH_BAR as default
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:22 +05:30
Philipp Tomsich
2acc24fc28 Kconfig: Migrate BOUNCE_BUFFER
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.

This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).

This commit includes a full migration using moveconfig.py to ensure
that each commit compiles.  To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.

[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
2019-01-19 09:49:26 -05:00
Tom Rini
4114a2614b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-13 19:44:53 -05:00
Tom Rini
b2f90c461e Merge branch 'master' of git://git.denx.de/u-boot-imx 2018-09-04 17:45:53 -04:00
Ye Li
536c5c7a33 imx: imx6sx-sdb: Enable DM QSPI driver
To support DM QSPI driver
 - Add spi0 and spi1 alias for qspi1 and qspi2.
 - Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
   to "spi-flash" and add "num-cs" property.
 - Enable DM SPI/QSPI relavent configurations
 - Remove iomux settings of qspi2 in board codes which is not needed
   for DM driver.
 - Add sf default settings. So running "sf probe" can detect the flash

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Alex Kiernan
d91013034a Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
2018-04-08 23:05:58 -04:00
Mario Six
07dea2e737 treewide: Migrate CONFIG_FSL_ESDHC to Kconfig
Migrate the CONFIG_FSL_ESDHC option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 18:31:05 -04:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Peng Fan
5dfc9d3766 imx: mx6sxsabresd: Enable DM driver
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Peng Fan
83fccaf1f9 ARM: imx: Enable dts for i.MX6SX-SDB
Enable DTS and OF_CONTROL for i.MX6SX-SDB.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12 14:28:04 +01:00
Fabio Estevam
6ca03f0dfb mx6sxsabresd: Load the correct dtb for revA board
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.

While at it, remove an extra 'mmc dev'.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-29 11:18:59 +01:00
Fabio Estevam
b47b705310 imx: Unify CONFIG_BOOTDELAY
In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-12-29 11:17:22 +01:00
Fabio Estevam
f086812acd mx6sxsabresd: Use PARTUUID to specify the rootfs location
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.

Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.

In order to avoid such issue, use the UUID method to specify the
rootfs location.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-11-27 10:35:19 +01:00
Tom Rini
73dd818cc4 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-30 12:58:33 -04:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Chris Packham
f58ad98a62 usb: net: migrate USB Ethernet adapters to Kconfig
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08 10:23:00 -04:00
Chris Packham
ae3584498b usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08 10:21:46 -04:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Simon Glass
6500ec7a5a Convert CONFIG_CMD_PCI to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:50 -04:00
Alexandru Gagniuc
3146f0c017 Move PHYLIB to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:28 -05:00
Tom Rini
fb82fe3851 configs: Resync defconfigs
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-19 09:47:40 -04:00
Simon Glass
0f7102588c Convert CONFIG_CMD_BMP to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BMP

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:30:08 -04:00
Simon Glass
218257b01a Convert CONFIG_CMD_BMODE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BMODE

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:30:06 -04:00
Tom Rini
af27382e2d drivers/pci/Kconfig: Add PCI
Add 'PCI' as a menu option and migrate all existing users.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-10-27 20:33:56 -04:00
Simon Glass
ef26d6039a Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_CONSOLE_IS_IN_ENV
   CONFIG_CONSOLE_MUX

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-23 18:33:35 -04:00
Simon Glass
27604b158f Convert CONFIG_VIDEO to Kconfig
This converts the following to Kconfig:
   CONFIG_VIDEO

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-23 18:33:21 -04:00
Tom Rini
645176d1d5 configs: Migrate CONFIG_USB_STORAGE
In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09 14:59:35 -04:00
Tom Rini
7802ce910b configs: Re-sync BOOTDELAY changes
With updated moveconfig.py and an better default, re-generate
the migration of BOOTDELAY to the defconfig.

Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-17 09:34:49 -04:00
Tom Rini
89cb2b5f8b configs: Re-sync with cmd/Kconfig
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:09:47 -04:00
Tom Rini
78d1e1d0a1 configs: Re-sync almost all of cmd/Kconfig
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND.  Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:09:40 -04:00
Tom Rini
adad96e60d configs: Re-sync HUSH options
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files.  Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-25 14:22:43 -04:00
Peng Fan
9131c18cfa imx: mx6sx: move MX6SX to Kconfig entry
If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX6SX" to boards using i.MX6 SoloX.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-26 14:16:12 +01:00
Simon Glass
69e173eb57 Move CONFIG_OF_LIBFDT to Kconfig
Move this option to Kconfig and tidy up existing boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14 14:50:25 -04:00
Thomas Chou
e4aa8edb6e common: add CMD_GPIO to Kconfig
Add CMD_GPIO to Kconfig and run tools/moveconfig.py .

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-18 14:50:06 -05:00
Peng Fan
21782828f9 imx: mx6 move TARGET_xx Kconfig option to mx6 specific Kconfig file
Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig.
Add enable "CONFIG_ARCH_MX6" for boards based on mx6.
Then we can choose target boards using "make ARCH=arm menuconfig"
with ARCH_MX6 defined.

If using original way, we have no chance to enable ARCH_MX6 when
"make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig,
kconfig will complains "arch/../configs/platinum_titanium_defconfig:3:
warning: override: TARGET_PLATINUM_TITANIUM changes choice state"

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Soeren Moch <smoch@web.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-09-02 15:29:14 +02:00