With the latest changes to add support for the Chromebook Bob,
initialisation through debug_uart_init() did no longer get called for
other targets.
Fix this, by moving debug_uart_init() out of the Bob-specific
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
These board files have inconsistent #include ordering. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 SPL has two cases that may end in a hard-stop: if either
the pinctrl can not be initialised or if the DRAM fails to initialise.
Both have previously not triggered an error message unless DEBUG was
defined (i.e. both used debug() to print the error).
This converts both error messages to be printed using pr_err() to
ensure that some output points to the cause of the hard-stop.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Without the patch SPL (in case of an error) creates an output like:
U-Boot SPL board initMissing DTB
The patch adds the missing line feed. So now we get:
U-Boot SPL board init
Missing DTB
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This implements the new 'spl_perform_fixups' hook for RK3399-based
boards and injects the /chosen/u-boot,spl-boot-device with an ofpath
corresponding to the boot device used.
The intended usage is for the full U-Boot stage to evaluate this in
scripts and then adapt its boot-order when using distro-boot.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.
The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.
To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it. There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.
All the existing call-sites are adjusted to match the changed function
signature.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
To support the new "same-as-spl" specifier in the boot-order on the
RK3399, this implements the chip-specific mapping from the information
obtainable from the BROM to a OF path name.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The later-stage spl_board_init (as opposed to board_init_f) should set
up board-specific details: these differ between the EVB-RK3399 and the
RK3399-Q7 (Puma).
This moves spl_board_init back into the individual boards and removes
the unneeded functionality from Puma.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Instead of directly calling into the back-to-bootrom code, the RK3399
common SPL implementation now uses BOOT_DEVICE_BOOTROM to trigger a
transfer back into the bootrom.
With this factored out, the spl_board_init function can not be
customised for each RK3399 board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL
enabled: this allows the use of syscon to retrieve the addresses of
GRF and SGRF (except for the early debug UART setup, which runs so
early that the device-model is not initialised).
This removes the hard-coded addresses and goes through syscon to
retrieve the base-addresses of GRF and SGRF. After that, we use
the structure definitions to locate the respective registers.
In addition to this, the inclusion of header files is also cleaned up:
- all headers are included at the beginning (there was a spurious
inclusion of the grf header from within a function)
- all #include statements for unused headers are removed
- the remaining #include statements are sorted (while keeping common.h
included in front)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdtdec.h is included, but not used in rk3399-board-spl.c: remove the
'#include'-statement.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In order to reuse the support for the u-boot,spl-boot-order property
from the rk3399, we split it into a reusable module that can be
included by the SPL code for any of our boards.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The back-to-bootrom option is rather unfortunately named
CONFIG_ROCKCHIP_SPL_BACK_TO_BOOTROM
instead of
CONFIG_SPL_ROCKCHIP_BACK_TO_BOOTROM
To make is selectable through CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BOOTROM),
we need to rename it. At the same time, we introduce a TPL_ variant of
the option to give us finer-grained control over when it should be used.
This change is motivated by our RK3368 boot process, which returns to
the boot ROM only from the TPL stage, but not from the SPL stage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[added fix-up for evb-rk3229_defconfig and phycore-rk3288_defconfig:]
[fixed inverted CONFIG_IS_ENABLED test for rk3288:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
include/configs/rock.h: undef
Some host like SD and eMMC may use DMA to transter data to SRAM,
set memory to non-secure to make sure the address can be accessed.
The security of SRAM in OS suppose to initialized in ATF bl31, and
the SPL is before the bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).
To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.
As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.
As the RK3399 needs to use its board_debug_uart_init() function, we
have Kconfig enable it by default for RK3399 builds.
With everything set up to define CONFIG_BAUDRATE via defconfig and
with to have the SPL debug UART either on UART0 or UART2, the configs
for the RK3399 EVB are then update (the change for the RK3399-Q7 is
left for later to not cause issues on applying the change).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 hangs during DMA of the Designware MMC controller, when
performing DMA-based transactions in SPL due to the DDR security settings
left behind by the BootROM (i.e. accesses to the first MB of DRAM are
restricted... however, the DMA is likely to target this first MB, as it
transfers from/to the stack).
System security is not affected, as the final security configuration is
performed by the ATF, which is executed after the SPL stage.
With this fix in place, we can now drop 'fifo-mode' in the DTS for the
RK3399-Q7 (Puma).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 does not have any boot selection pins and the BootROM probes
the boot interfaces using the following boot-order:
1. SPI
2. eMMC (sdhci in DTS)
3. SD card (sdmmc in DTS)
4. USB loader
For ease of deployment, the SPL stage should mirror the boot order of
the ROM and use the same probing order (assuming that valid images can
be detected by SPL) unless instructed otherwise. The boot-order can
then be configured via the 'u-boot,spl-boot-order' property in the
chosen-node of the DTS.
While this approach is easily extensible to other boards, it is only
implemented for the RK3399 for now, as the large SRAM on the RK3399
makes this easy to fit the needed infrastructure into SPL and our
production setup already runs with DM, OF_CONTROL and BLK in SPL.
The new boot-order property is expected to be used in conjunction with
FIT images (and all legacy image formats disabled via Kconfig).
A boot-sequence with probing and fallthroughs from SPI via eMMC to SD
card (i.e. &spiflash, &sdhci, &sdmmc) has been validated on the RK3399-Q7.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add SPL support for rk3399, default with of-platdata enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop Kconfig changes to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
