Commit graph

34 commits

Author SHA1 Message Date
Lokesh Vutla
7b92252370 ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
Rajendra Nayak
8c16dd6fa7 ARM: OMAP: Fix handling of errata i727
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-07-25 16:26:11 -04:00
Simon Glass
7e4154a553 am33xx/omap: Allow cache enable for all Sitara/OMAP
Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined.
This speeds up the Beaglebone Black boot considerable.

(Tested only on Beaglebone Black with SD card boot)

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-11 16:25:39 -04:00
Lokesh Vutla
d7630da6f4 ARM: OMAP: Fix omap_sdram_size calculation
Last section of DMM is used for trapping tiler unmapped sections.
Corresponding trap_size should be deducted from total SDRAM size
only if trap section is overlapping with available SDRAM
based on DMM sections. Fixing the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23 19:40:38 -04:00
Tom Rini
939911a64b armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_context
The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same.  In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.

Cc: Sricharan R. <r.sricharan@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23 19:40:05 -04:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Masahiro Yamada
365475e6d1 Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to callee
- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Jassi Brar
e81f63f0d2 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALL
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:38:39 -05:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Lokesh Vutla
3332b24421 ARM: DRA7xx: clocks: Fixing i2c_init for PMIC
In DRA7xx Soc's voltage scaling is done using GPI2C.
So i2c_init should happen before scaling. I2C driver
uses __udelay which needs timer to be initialized.
So moving timer_init just before voltage scaling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Tom Rini
4596dcc1d4 am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.c
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common.  Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx.  Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.

Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-05 08:46:49 -04:00
Tom Rini
0ac6db2631 omap-common/hwinit-common.c: Mark omap_rev_string as static
Only called in this file, mark as static.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-04 16:32:31 -04:00
SRICHARAN R
47c6ea076e ARM: OMAP: Add arch_cpu_init function
The boot parameters passed from SPL to UBOOT
must be saved as a part of uboot's gd data
as early as possible, before we will inadvertently
overwrite it. So adding a arch_cpu_init for the required
Socs to save it.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:56 -04:00
SRICHARAN R
fda06812a0 ARM: OMAP: Correct save_boot_params and replace with 'C' function
Currently save_boot_params saves the boot parameters passed
from romcode. But this is not stored in a writable location
consistently. So the current code would not work for a
'XIP' boot. Change this by saving the boot parameters in
'gd' which is always writable. Also add a 'C' function
instead of an assembly code that is more readable.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-05-10 08:25:56 -04:00
R Sricharan
de63ac278c ARM: mmu: Set domain permissions to client access
The 'XN' execute never bit is set in the pagetables. This will
 prevent speculative prefetches to non executable regions. But the
 domain permissions are set as master in the DACR register.
 So the pagetable attribute for 'XN' is not effective. Change the
 permissions to client.

 This fixes lot of speculative prefetch aborts seen on OMAP5
 secure devices.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Vincent Stehle <v-stehle@ti.com>
Cc: Vincent Stehle <v-stehle@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-28 09:10:58 +01:00
Lokesh Vutla
de62688bb6 arm: dra7xx: Add silicon id support for DRA752 soc
Adding CPU detection support for the DRA752 ES1.0 soc.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:39:57 -04:00
Lokesh Vutla
d4d986ee27 ARM: OMAP5: srcomp: enable slew rate compensation cells after powerup
After power-up SRCOMP cells are by-passed by default in OMAP5.
Software has to enable these SRCOMP sells.
For ES2: All 5 SRCOMP cells needs to be enabled.
For ES1: Only 4 SRCOMP cells in core power domain are enabled.
	 The 1 in wkup domain is not enabled because smart i/os
	 of wkup domain work with default compensation code.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
2013-03-11 11:06:11 -04:00
Lokesh Vutla
c43c8339fe ARM: OMAP4+: Make control module register structure generic
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
SRICHARAN R
01b753ff7b ARM: OMAP4+: Change the PRCM structure prototype common for all Socs
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.

Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-03-11 11:06:09 -04:00
Tom Rini
6507f133f3 SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linux
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r.  We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well.  Finally, we no longer call
relocate_code so remove that from the armv7 version.

Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
47f7bcae8c SPL: Move the omap SPL framework to common/spl
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards.  We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/.  We leave
the NAND one in-place as we plan to replace it later in this series.

We use common/spl to avoid linker problems with respect to merging
constant strings in objects.   Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
55cdbb8d4e ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:57 -07:00
Tom Rini
861a86f460 omap-common: SPL: Add CONFIG_SPL_DISPLAY_PRINT / spl_display_print()
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing.  Change how this works to
be opt-in and only turned on for omap4/5 now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:48:38 -07:00
Lokesh Vutla
38f25b125e OMAP4+: Force DDR in self-refresh after warm reset
Errata ID:i727

Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.

Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.

This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
2012-07-07 14:07:35 +02:00
SRICHARAN R
e06e914d87 ARM: OMAP4+: dmm: Take care of overlapping dmm and trap sections.
The DMM sections can be overlapping with each other, with
sections 3 to 0 having the highest to lowest priority in that
order. There could also be a section that is used trap the
unmapped Tiler entries and this trap section could be
overlapping with the actual sdram area.

So take care of the above scenarios while calculating the
size of the actual ram.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:21 +02:00
Tom Rini
aa2889c8c3 omap4+: Remove CONFIG_ARCH_CPU_INIT
OMAP4/5 had an empty arch_cpu_init() so drop that along with
CONFIG_ARCH_CPU_INIT

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
SRICHARAN R
c1fa3c37af OMAP4/5: device: Add support to get the device type.
Add support to identify the device as GP/EMU/HS.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:24 +02:00
Dechesne, Nicolas
f59021791b OMAP SPL: Fix missing timer_init() call in OMAP4 s_init()
In 8775471bb, the call to timer_init() was removed from common code
and put in OMAP3 s_init() function. As a result the boot was broken
on OMAP4. This patch adds timer_init() in OMAP4 s_init(), that fix
boot on all OMAP4 boards.

Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com>
Tested-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
2012-02-12 10:11:23 +01:00
Andreas Müller
761ca31e47 omap_rev_string: output to stdout
* avoid potential buffer overflows
* allow SPL-build not to output "Texas Instruments Revision detection unimplemented"

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:13 +01:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Sricharan
78f455c055 omap4/5: Add support for booting with CH.
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
bb772a5944 omap5: emif: Add emif/ddr configurations required for omap5 evm
Add the emif configurations required for omap5 soc.Add the
correct ddr part configurations required for omap5 evm board.
EDB8164B3PH from ELPIDA is the part used on the board.

Also changes are done to retain some part of the code
common for OMAP4/5 and keep only the remaining in the Soc
specific directories.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
ce170beeb7 omap4: make omap4 code common for future reuse
Much of omap4 soc support code can be reused for omap5.
Move them to the omap-common directory to facilitate
this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Renamed from arch/arm/cpu/armv7/omap4/board.c (Browse further)