* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
Signed-off-by: Wolfgang Denk <wd@denx.de>
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.
Signed-off-by: York Sun <yorksun@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.
The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.
Avoid updating these register.They will be programmed during NAND RAMBOOT.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).
So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Please refer doc/README.mpc85xx for more information
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.
As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires debug exception vecter (IVPR +
IVOR15) to have valid and fetchable OP code.
1) While executing in translated space (AS=1), whenever a debug exception is
generated, the MSR[DS/IS] gets cleared i.e. AS=0 and the processor tries to
fetch an instruction from the debug exception vector (IVPR + IVOR15); since now
we are in AS=0, the application needs to ensure the proper TLB configuration to
have (IVOR + IVOR15) accessible from AS=0 also.
Create a temporary TLB in AS0 to make sure debug exception verctor is
accessible on debug exception.
2) Just after relocation in DDR, Make sure IVPR + IVOR15 points to valid opcode
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register
Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- BSC9131 is integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
- BSC9130 is exactly same as BSC9131 except that the max e500v2
core and DSP core frequencies are 800M(these are 1G in case of 9131).
- BSC9231 is similar to BSC9131 except no MAPLE
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
including IEEE 1588. v2 hardware support and virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single port)
and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
This patch takes care of code pertaining to power side functionality only.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The misspelling of "semiconductor" causes some internal copyright analysis
tools to complain.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:
$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1
--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with errors: 1 ( MPC8572DS )
----------------------------------------------------------
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Fix this:
ether_scc.c: In function 'mpc82xx_scc_enet_initialize':
ether_scc.c:377:14: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:453:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:390:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
fec.c: In function 'mpc8220_fec_recv':
fec.c:791:9: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
fec.c: In function 'mpc8220_fec_initialize':
fec.c:839:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Commit db288a9 "net: Remove volatile from net API" caused a number of
build warnings:
fec.c: In function 'fec_initialize':
fec.c:183:13: warning: assignment from incompatible pointer type [enabled by default]
fec.c: In function 'fec_recv':
fec.c:284:5: warning: passing argument 1 of 'NetReceive' discards 'volatile' qualifier from pointer target type [enabled by default]
/home/wd/git/u-boot/work/include/net.h:433:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
scc.c: In function 'scc_initialize':
scc.c:85:14: warning: assignment from incompatible pointer type [enabled by default]
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
* 'master' of git://git.denx.de/u-boot-nand-flash:
NAND: Remove ONFI detection message to from bootup log
driver/mtd:IFC: Fix possible memory leak
driver/mtd: IFC NAND: Add support of ONFI NAND flash
mtd, nand: move some printfs to debug output.
nand_util: correct YAFFS image write function
powerpc/85xx: fix NAND boot linker scripts for -fpic
nand: extend .raw accesses to work on multiple pages
GOT is now handled the way the main u-boot.lds does it. Without this,
the boot hangs when built with newer GCC (since 4.6). Older toolchains
hid the issue by converting -fpic to -fPIC.
Signed-off-by: Scott Wood <scottwood@freescale.com>
All arches init this the same way, so move the logic into the core
net code to avoid duplicating it everywhere else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.
Signed-off-by: Timur Tabi <timur@freescale.com>
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.
Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Currently "u-boot", the elf file generated via u-boot-nand.lds does not
contain required debug information i.e. .debug_{line, info, abbrev, aranges,
ranges} into their respective _global_ sections.
The original ld script line arch/powerpc/cpu/mpc85xx/start.o
KEEP(*(.bootpg)) is not entirely correct because the start.o file is already
processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will
not process start.o again for bootpg.
So Fix u-boot-nand.lds to generate these debug information.
Signed-off-by: Anmol Paralkar <b07584@freescale.com>
Signed-off-by: John Russo <John.Russo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
NAND SPL code never compile the vector table.
So no need to setup interrupt vector table for NAND SPL.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After relocation of vector table in SDRAM's lower address, IVORs value should
be updated with new handler addresses.
As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs
are updated with 0x100, 0x200,....f00 hard-coded values.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.
in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This seems to be unsigned char for no good reason. Tidy this up and
remove the casts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add support for fixing usb mode and phy type for
MPH(Multi Port Host) USB controllers in device-tree nodes.
Required for socs like P3060, P5020, etc having MPH USB controller
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Some code cleanup done for USB device-tree fixup:
- handling error value returned from fdt_fixup_usb_mode_phy_type()
- using ARRAY_SIZE macro
- using snprintf instead of sprintf
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
fsl_lbc: add printout of LCRR and LBCR to local bus regs
sbc8548: Fix up local bus init to be frequency aware
sbc8548: enable support for hardware SPD errata workaround
sbc8548: relocate fixed ddr init code to ddr.c file
sbc8548: Make enabling SPD RAM configuration work
sbc8548: Fix LBC SDRAM initialization settings
sbc8548: enable ability to boot from alternate flash
sbc8548: relocate 64MB user flash to sane boundary
Revert "SBC8548: fix address mask to allow 64M flash"
MPC85xxCDS: Fix missing LCRR_DBYP bits for 66-133MHz LBC
eXMeritus HWW-1U-1A: Add support for the AT24C128N I2C EEPROM
eXMeritus HWW-1U-1A: Minor environment variable tweaks
It can be handy to have these in the output when trying to
debug odd behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In the current u-boot code, the value of these fields are the reserved
value (0b100), through the signal integrity measurement on freescale's
board with these reserved setting, the signal eye is out of the recommended
spec for non-transition amplitude at 500mV nominal.
According to the errata for MPC8379E, we should make a change to the
recommended setting from essentially nothing at this time to 0b001 for SATA.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We already flush the kernel image after we've loaded it to ensure
visiblity to the other cores. We need to do the same thing for the
ramdisk and device tree images. In AMP boot scenarios we might not be
HW cache coherent with the secondary core that we are loading and
setting the ramdisk and device tree up for. Thus we need to ensure
we've flushed the regions of memory utilized by ramdisk and device tree
so the loadding and any modifications (from decompression or fdt updates)
are made visible to the secondary cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standard Debian powerpc and powerpcspe systems only include hard-float
libgcc in their native compilers, which causes scary build warnings when
building U-Boot.
Debian and other PowerPC-supporting distributions used to provide libgcc
and other libraries in a "nof" (soft-float) form in the "multilib"
packages. As they were completely unused by the distribution and
therefore tended to be very buggy it was decided to save some time on
the part of the maintainers and build-servers by removing them.
Admittedly, right now the linker warnings do not indicate any problems,
as the included routines do not use any floating point at all.
The concern is that if floating-point code were ever added it might
cause hard-float code to be unexpectedly included in U-Boot without
generating a hard error. This would cause unexplained crashes or
indeterminate results at runtime.
The easiest way to resolve this is to borrow the routines that U-Boot
needs from the Linux kernel, which has the same issue.
Specifically, the routines are: _ashldi3(), _ashrdi3(), and _lshrdi3().
They were borrowed from arch/powerpc/kernel/misc_32.S as of v2.6.38-rc5,
commit 85e2efbb1db9a18d218006706d6e4fbeb0216213, and are GPLv2+.
The Makefile framework was copied from the U-Boot ARM port.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Stefan Roese <sr@denx.de>
