The Firefly ROC_RK3308_CC use ref_clock of input mode,
and rmii pins of m1 group.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3308 only support RMII mode, and if it is output clock
mode, better to use ref_clk pin with drive strength 12ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the glue code to allow the rk3308 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is a core board named Core-PX30-JD4 with a mainboard from Firefly,
name it as firefly-px30 for now.
This board can re-use the dts of PX30, the only difference is the UART IO,
the firefly use UART2 M1 while evb use UART2 M0.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
serial# is one of the vendor properties and thus protected from being
overwritten if already set. If env_set is called anyway this result in
some nasty warnings, so check for presence before trying that.
In the same direction check for the presence of cpuid# and compare it
to the actual hardware and emit a warning if they don't match.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_setup_macaddr() runs from an initcall, so returning an error
code will make that initcall fail thus breaking the boot process.
And if an ethernet address is already set this is definitly not a
cause for that, so just return success in that case.
Fixes: 0482538499 ("rockchip: rk3399: derive ethaddr from cpuid");
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some generic PX30 SoMs found in the wild use UART3 as their debug output
instead of UART2 (used for MMC) and UART5.
Make it possible to use UART3 as early debug output, with the associated
clock and pinmux configuration. Two sets of output pins are supported (M0/M1).
Future users should also note that the pinmux default in the dts is to use
the M1 pins while the Kconfig option takes M0 as a default.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
UART3 also has two sets of pins that can be selected.
Rename the config option to a common name, to allow it to be used for both
UART2 and UART3.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
According to the PX30 TRM, the iomux registers come first, before the pull
and strength control registers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
And show my best respect to Heiko's work for this solution.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After commit d8765e2422 ("Enable building of u-boot.itb
on Rockchip platform"), u-boot.itb will automatically
generated by "make all" command, manually command
"make u-boot.itb" is no longer needed.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SPL has limited available resources, and the performance between
ARM and Thumb isn't that significant.
This patch builds using Thumb instruction set to reduce the code
size by nearly 6K.
Original:
text data bss dec hex filename
26526 4004 1376 31906 7ca2 spl/u-boot-spl
Thumb:
text data bss dec hex filename
20232 4004 1376 25612 640c spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The da850-evm doesn't have the boot pins configured in a way
to make MMC/SD booting an option, and MMC/SD support is not
enabled in SPL. Therefore, there is no need to support raw mode
mmc/sd support in SPL.
This patch disables CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
Signed-off-by: Adam Ford <aford173@gmail.com>
At the moment entry_point is set to image_get_load(header) that sets it
to "load address" instead of "entry point", assuming entry_point is
equal to load_addr, but it's not true. Then load_addr is set to
"entry_point - header_size", but this is wrong too since load_addr is
not an entry point.
So use image_get_ep() for entry_point assignment and image_get_load()
for load_addr assignment.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
# This is actually a resent patch of
# [1] https://lists.denx.de/pipermail/u-boot/2019-May/369170.html
Two test cases are added under test_fs_ext:
test case 10: for root directory
test case 11: for non-root directory
Those will verify a behavior fixed by the commits related to
root directory
("fs: fat: allocate a new cluster for root directory of fat32" and
"fs: fat: flush a directory cluster properly"), and focus on
handling long-file-name directory entries under a directory.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Unlink test for FAT file system seems to fail at test_unlink2.
(When I added this test, I haven't seen any errors though.)
for example,
===8<===
fs_obj_unlink = ['fat', '/home/akashi/tmp/uboot_sandbox_test/128MB.fat32.img']
def test_unlink2(self, u_boot_console, fs_obj_unlink):
"""
Test Case 2 - delete many files
"""
fs_type,fs_img = fs_obj_unlink
with u_boot_console.log.section('Test Case 2 - unlink (many)'):
output = u_boot_console.run_command('host bind 0 %s' % fs_img)
for i in range(0, 20):
output = u_boot_console.run_command_list([
'%srm host 0:0 dir2/0123456789abcdef%02x' % (fs_type, i),
'%sls host 0:0 dir2/0123456789abcdef%02x' % (fs_type, i)])
assert('' == ''.join(output))
output = u_boot_console.run_command(
'%sls host 0:0 dir2' % fs_type)
> assert('0 file(s), 2 dir(s)' in output)
E AssertionError: assert '0 file(s), 2 dir(s)' in ' ./\r\r\n ../\r\r\n 0 0123456789abcdef11\r\r\n\r\r\n1 file(s), 2 dir(s)'
test/py/tests/test_fs/test_unlink.py:52: AssertionError
===>8===
This can happen when fat_itr_next() wrongly detects an already-
deleted directory entry.
File deletion, which was added in the commit f8240ce95d ("fs: fat:
support unlink"), is implemented by marking its entry for a short name
with DELETED_FLAG, but related entry slots for a long file name are kept
unmodified. (So entries will never be actually deleted from media.)
To handle this case correctly, an additional check for a directory slot
will be needed in fat_itr_next().
In addition, I added extra comments about long file name and short file
name format in FAT file system. Although they are not directly related
to the issue, I hope it will be helpful for better understandings
in general.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
The mmc CID value is one of the input parameters used to provision the
RPMB key. The trusted execution environment expects this value to be
specified in big endian format.
Before this fix, on little endian systems, the value returned by the
linux kernel mmc driver differed from the one returned by u-boot.
This meant that if linux provisioned the RPMB key, u-boot would not
have access to the partition (and the other way around).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
The command cp fails on sandbox because the address is used
directly. To fix this issue, we call the function map_sysmem
to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The command iminfo fails on sandbox because the address
is used directly. To fix this issue, we call the function
map_sysmem to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This define indicates if DM_GPIO shall be supported in SPL. This allows
proper operation of DM converted GPIO drivers in SPL, which use
boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
PCI devices may be disabled in the device tree. Devices which are probed
by the device tree handle the "status" property and are skipped if
disabled. Devices which are probed by the PCI enumeration don't check
that property. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Defconfigs have been fixed, now we can add proper dependencies in
Kconfig. SPI FLASH is still not dependent on MTD (deeper rework needed).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
CONFIG_DFU_NAND needs the raw NAND core being compiled.
Also fix the colibri_vf defconfig to reflect this dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Enabling TFABOOT configuration will compile-in a call to nand_read in
the boot sequence. Handle the situation by also selecting officially
the raw NAND core in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no flash on this board, there is no reason to define MTD
environment variables nor UBI. Drop them from the configuration file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Wolfgang Grandegger <wg@aries-embedded.de>
While the right Kconfig entries were selected, because of the missing
CMD_NAND symbol the raw NAND core was never compiled. Remove it from
the defconfigs otherwise the build will fail.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Also do this on bcm11130_nand]
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to previous Makefile organization, the raw NAND subdirectory was
not compiled in if CMD_NAND was not enabled. Because the Denali driver
does not compile with these boards (undefined environment offset),
remove the dependency within the defconfig over the controller driver
(was ignored anyway in the past).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's be consistent and always declare CONFIG_MTD from the defconfig
file when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD support must be enabled when using mtdparts. Indeed, functions
like get_mtd_info(), get_mtd_device() and put_mtd_device() are in
drivers/mtd/mtd_uboot.c and are built only with CONFIG_MTD.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
In some files, options of CMD_NAND are selected but not the command
itself. Fix this inconsistency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Raw NAND support must be enabled when the environment is in NAND.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI must be enabled when the environment is in UBI.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI must be enabled when using fastmap, reflect this is defconfigs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on M2N Gose.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on M2W Koelsch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Lager.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
