Commit graph

18 commits

Author SHA1 Message Date
Codrin Ciubotariu
9101a68c15 drivers: net: vsc9953: Fix bug when PVID is shown for disabled ports only
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:34:44 -07:00
Codrin Ciubotariu
02c00f265d drivers: net: vsc9953: Do not configure disabled ports
Some SerDes protocols might not enable all l2switch ports. In this case,
these ports should not be configured to perform Rx/Tx operations.
This also fixes an issue when flooded frames were also switched to
disabled ports and frames start to accumulate, consuming memory
and eventually causing head-of-line blocking for other frames.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:34:18 -07:00
Codrin Ciubotariu
aae0e68909 drivers: net: vsc9953: Add LAG support
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}

A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.

For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:19 -06:00
Codrin Ciubotariu
ba389e65e5 drivers: net: vsc9953: Fix FDB aging time
By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:08 -06:00
Codrin Ciubotariu
a857d5f835 drivers/net/vsc9953: Add GPL-2.0+ SPDX-License-Identifier
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:48 -07:00
Codrin Ciubotariu
5ed1bacd34 drivers/net/vsc9953: Add commands for VLAN ingress filtering
The command:
ethsw [port <port_no>] ingress filtering
     { [help] | show | enable | disable }
  - enable/disable VLAN ingress filtering on port

can be used to enable/disable/show VLAN ingress filtering on a port.
This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:48 -07:00
Codrin Ciubotariu
21d214fcd0 drivers/net/vsc9953: Add command for shared/private VLAN learning
The command:
ethsw vlan fdb { [help] | show | shared | private }
 - make VLAN learning shared or private"

configures the FDB to share the FDB entries learned on multiple VLANs
or to keep them separated. By default, the FBD uses private VLAN
learning. This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:48 -07:00
Codrin Ciubotariu
a2477924cd drivers/net/vsc9953: Add VLAN commands for VSC9953
The new added commands can be used to configure VLANs for a port
on both ingress and egress.

The new commands are:
ethsw [port <port_no>] pvid { [help] | show | <pvid> }
 - set/show PVID (ingress and egress VLAN tagging) for a port;
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> }
 - add a VLAN to a port (VLAN members);
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid }
 - set egress tagging mod for a port"
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified }
 - Configure VID source for egress tag. Tag's VID could be the
   frame's classified VID or the PVID of the port
These commands have also been added to the ethsw generic parser from
common/cmd_ethsw.c

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:48 -07:00
Codrin Ciubotariu
22449858f8 drivers/net/vsc9953: Add commands to manipulate the FDB for VSC9953
The new command:
ethsw [port <port_no>] [vlan <vid>] fdb
        { [help] | show | flush | { add | del } <mac> }

Can be used to add and delete FDB entries. Also, the command can be used
to show entries from the FDB tables. When used with [port <port_no>]
and [vlan <vid>], only the matching the FDB entries can be seen or
flushed. The command has also been added to the generic ethsw parser
from cmd_ethsw.c.

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:47 -07:00
Codrin Ciubotariu
68c929da6b drivers/net/vsc9953: Add commands to enable/disable HW learning
The command:
ethsw [port <port_no>] learning { [help] | show | auto | disable }

can be used to enable/disable HW learning on a port.
This patch also adds this command to the generic ethsw parser from
cmd_ethsw.

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:47 -07:00
Codrin Ciubotariu
86719f0cd5 drivers/net/vsc9953: Add command to show/clear port counters
The new added command:
ethsw [port <port_no>] statistics { [help] | [clear] }

will print counters like the number of Rx/Tx frames,
number of Rx/Tx bytes, number of Rx/Tx unicast frames, etc.
This patch also adds this commnd in the genereric ethsw
parser from cmd_ethsw.c

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:47 -07:00
Codrin Ciubotariu
24a23deb90 drivers/net/vsc9953: Use the generic Ethernet Switch parser
This patch replaces the parser used by VSC9953 L2 Switch driver with
the generic one. Also, the config macro that enables the
VSC9953 commands has been replaced in all the platforms that
use this driver with the config macro that corresponds to the
generic parser.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:47 -07:00
Codrin Ciubotariu
9de059871f drivers/net/vsc9953: Add default configuration for VSC9953 L2 Switch
At startup, the default configuration should be:
 - enable HW learning on all ports (HW default);
 - all ports are VLAN aware;
 - all ports are members of VLAN 1;
 - all ports have Port-based VLAN 1;
 - on all ports, the switch is allowed to remove
   maximum one VLAN tag,
 - on egress, the switch should add a VLAN tag if the
   frame is classified to a different VLAN than the port's
   Port-based VLAN;

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:46 -07:00
Codrin Ciubotariu
fe91095b79 drivers/net/vsc9953: Fix bug when enabling a port
When a port is enabled at init time, the initializing function
touches more bits than necessary to enable a port (also touches
reserved bits and default bit values). This patch fixes this issue
by changing the value of the define used to enable the port and
assures that no other bits are changes by replacing out_le32()
with setbits_le32().

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:46 -07:00
Codrin Ciubotariu
3cc8cfffb2 drivers/net/vsc9953: Cleanup patch
This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" words are replaced with "port_no",
puts each variable declaration on a line and removes
unnecessary tabs.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:46 -07:00
Codrin Ciubotariu
c4390486a6 drivers/net/vsc9953: Remove 'CONFIG_' from macros' name
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-21 08:29:46 -07:00
Shaohui Xie
cd348efa6c net/memac_phy: reuse driver for little endian SoCs
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:57 -07:00
Codrin Ciubotariu
6706b115a6 net/vsc9953: Add driver for Vitesse VSC9953 L2 Switch IP
This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP
is integrated in Freescale T1040 and T1020 SoCs.
The L2 switch has 10 Ethernet ports: 2 internal fixed-links
(ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps.
The external ports may be connected to PHYs over QSGMII and SGMII.

Commands have also been added to enable/disable a port and to
check a port's link speed, duplexity and status. The commands are:

ethsw port <port_nr> enable|disable - enable/disable an l2 switch port
ethsw port <port_nr> show - show an l2 switch port's configuration

port_nr=0..9; use "all" for all ports

For more detailse please see doc/README.t1040-l2switch

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16 09:32:38 -08:00