Commit graph

12212 commits

Author SHA1 Message Date
Jagan Teki
f838ebfe5a ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.

With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver

While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY

Similar fix has merged for i.Core MX6Q but missed to update for DL.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-07 10:26:57 +01:00
Jagan Teki
d159b0236b ARM: dts: icorem6: Sync engicam device trees from v5.4
Sync Engicam device tree file from v5.4 linux-next.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-07 10:26:57 +01:00
Rasmus Villemoes
abaf5c9804 arm: mxs: be more careful when enabling gpmi_clk
The data sheet says that the DIV field cannot change while the CLKGATE
bit is set or modified. So do it a little more carefully, by first
clearing the bit, waiting for that to appear, then setting the DIV
field.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07 10:26:57 +01:00
Rasmus Villemoes
fb94625229 arm: mxs: fix comments in arch_cpu_init to match the code
The comment says to clear the bypass bit, but in fact it sets it, thus
selecting ref_xtal. And the next line of code does not set the divider
to 12, but to (the reset value of) 1.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07 10:26:57 +01:00
Rasmus Villemoes
bb09bd5f69 arm: mxs: fix register definitions for clkctrl_gpmi and clkctrl_sspX
I tried clearing a bit by writing to hw_clkctrl_gpmi_clr, then
busy-waiting for it to actually clear. My board hung. The data sheet
agrees, these registers do not have _set, _clr, _tog, so fix up the
definitions. git grep -E 'clkctrl_(gpmi|ssp[0-9])_' says that nobody
uses those non-existing ops registers.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07 10:26:57 +01:00
Igor Opaniuk
061b63b775 mach-imx: nandbcb: improve cmd help
Add info about supported i.MX7, improve details the usage of
bcbonly subcommand.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:57 +01:00
Frieder Schrempf
83083febf5 ddr: imx8m: Return error values from LPDDR4 training
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.

Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2020-01-07 10:26:57 +01:00
Tom Rini
44ad496143 arm: imx: Default to SYS_THUMB_BUILD for i.MX6/7
In the case of i.MX6 and i.MX7 family SoCs it is safe (from an errata
point of view) to use thumb2 by default to save space.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07 10:26:57 +01:00
Igor Opaniuk
c0f037f6a2 mach-imx: bootaux: elf firmware support
Currently imx-specific bootaux command doesn't support ELF format
firmware for Cortex-M4 core.

This patches introduces a PoC implementation of handling elf firmware
(load_elf_image_phdr() was copy-pasted from elf.c just for PoC).
ELF64 binaries isn't supported yet.

This has the advantage that the user does not need to know to which
address the binary has been linked to. However, in order to handle
and load the elf sections to the right address, we need to translate the
Cortex-M4 core memory addresses to primary/host CPU memory
addresses (Cortex A7/A9 cores).

This allows to boot firmwares from any location with just using
bootaux, e.g.:
> tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}

Similar translation table can be found in the Linux remoteproc
driver [1].

[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Igor Opaniuk
45997eb6c0 ARM: dts: imx7: imx7_colibri: introduce fec node
Sync DTS with the mainline Linux and introduce fec node and
regulator configuration for rn5t567 PMU.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Igor Opaniuk
f9be62a608 ARM: dts: imx6_apalis: introduce fec node
Sync DTS with the mainline Linux and introduce fec node.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Igor Opaniuk
fbcd88095d ARM: dts: imx6_colibri: introduce fec node
Sync DTS with the mainline Linux and introduce fec node.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Joris Offouga
0d52bab462 mx7dsabre: Enable DM_ETH
Also sync device tree with v5.5-rc1
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2020-01-07 10:26:56 +01:00
Fabio Estevam
0417ef17ac mx7ulp: Add support for Embedded Artists COM board
The Embedded Artists COM board is based on NXP i.MX7ULP.

It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).

Add the initial support for the board.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-01-07 10:26:56 +01:00
Steffen Dirkwinkel
ba1444eab6 imx: cx9020: migrate cx9020 to CONFIG_DM_USB
Note: gpio7_8 was never used for usb power regulator so we remove it here

Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2020-01-07 10:26:56 +01:00
Steffen Dirkwinkel
9c2b1b0f03 imx: cx9020: migrate cx9020 to CONFIG_DM_ETH
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2020-01-07 10:26:56 +01:00
Parthiban Nallathambi
d98929d636 imx: sync with kernel device tree for Phycore SoM
Sync the Linux Kernel 5.4-rc6 device tree for Phytec Phycore
SoM and Segin board based on imx6UL and imx6ULL.

Changes includes Phytec naming convention for the devicetree files.

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2020-01-07 10:26:56 +01:00
Igor Opaniuk
89038264bb mach-imx: bootaux: add dcache flushing before enabling M4
This patch fixes the issue with broken bootaux command,
when M4 binary is loaded and data cache isn't flushed
before M4 core is enabled.

Reproducing:
> tftpboot ${loadaddr} ${board_name}/hello_world.bin
> cp.b ${loadaddr} 0x7F8000 $filesize
> bootaux 0x7F8000

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Igor Opaniuk
0ba1b4de0e mach-imx: bootaux: print stack pointer and reset vector
1. Change information printed about loaded M4 binary, print the stack
pointer and reset vector addressed.
2. Add sanity check for the address provided as param.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Marek Vasut
c35b19531d ARM: mx6: ddr: Add support for iMX6SX
This patch adds support for iMX6SX MMDC into the DDR calibration
code. The only difference between MX6DQ and MX6SX is that the SX
has 2 SDQS registers, while the DQ has 8.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07 10:26:56 +01:00
Marek Vasut
b314003fda ARM: mx6: ddr: Configure all SDQS pullups using loop
Instead of explicitly setting up each SDQS register, use a loop.
No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07 10:26:56 +01:00
Marek Vasut
7ec0e39ec4 ARM: mx6: ddr: Factor out SDQS configuration code
Pull out the code turning SDQS pullups on and off into a separate
function, since it is replicated in two places in the code and it
is the single place in the entire function which is SoC dependent.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07 10:26:56 +01:00
Marek Vasut
736b491f31 ARM: mx6: ddr: Make debug prints work with tiny printf
The %08X format returns just zeroes with tiny printf, which is
horribly confusing, especially when debugging DRAM calibration
problems. Change the format to %08x (with lowercase x), which
behaves correctly with either implementation of printf in SPL.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07 10:26:56 +01:00
Claudius Heine
f8420d7c0f ARM: dts: dh-imx6: add u-boot specific wdt-reboot node
The wdt-reboot node is needed for the sysreset_watchdog driver to
register a watchdog as a reset handler in case 'CONFIG_SYSRESET' is
enabled.

Signed-off-by: Claudius Heine <ch@denx.de>
2020-01-07 10:26:56 +01:00
Baruch Siach
281d5e435b arm: dts: hummingboard: add cubox/hummingboard DT (part 2 of 2)
These DT files are copied from kernel v5.3 with no changes.

This is part 2 of 2 commits. Included are DT files for SOM rev 1.5, and
Hummingboard2 Gate/Edge.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07 10:26:56 +01:00
Baruch Siach
730e6a0ca1 arm: dts: hummingboard: add cubox/hummingboard DT (part 1 of 2)
These DT files are copied from kernel v5.3 with no changes.

This is part 1 of 2 commits. Included are DT files for the original
Cubox-i and Hummingboard Base/Pro.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07 10:26:56 +01:00
Robert Beckett
7915e150d6 board: ge: mx53ppd: use imx wdt
Enable DM imx WDT
Enable SYSRESET_WATCHDOG to maintain WDT based reset ability

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07 10:26:56 +01:00
Robert Beckett
d494aeca46 board: ge: bx50v3: use imx wdt
Enable DM imx WDT
Enable SYSRESET_WATCHDOG to maintain WDT based reset ability

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07 10:26:56 +01:00
Robert Beckett
6388f9921a board: ge: ppd: sync device tree from Linux
Copy device tree from linux for PPD.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07 10:26:56 +01:00
Robert Beckett
8c26739859 board: ge: bx50v3: sync devicetrees from Linux
Copy device trees from linux, keeping them as separate files for
each board to ease future sync.

Update board code to use generic bx50v3 dt initially, then select
the specific dt based on board detection.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07 10:26:56 +01:00
Lukasz Majewski
010e58d448 imx: Add support for i.MX28 based XEA board
This patch introduces support for i.MX28 based XEA board.

This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.

U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error

U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)

CPU:   Freescale i.MX28 rev1.2 at 454 MHz
BOOT:  SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM:  128 MiB
MMC:   MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In:    serial
Out:   serial
Err:   serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot:  0

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-01-07 10:26:56 +01:00
Heiko Schocher
227cb30047 imx6: aristainetos: add support for rev C board
add support for revision C boards. This board has
no longer a NAND.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:56 +01:00
Heiko Schocher
c08aa77173 imx6: aristainetos: add aristainetos 2b csl
add aristainetso board version CSL.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:56 +01:00
Heiko Schocher
1204b9675e imx6: aristainetos: readd aristainetos 2b board
readd aristainetos 2b board.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:56 +01:00
Heiko Schocher
f44b4ab3c8 imx6: aristainetos: add DM_SERIAL support
add DM_SERIAL support for the aristainetos board, and
remove not used code from board code.

remove CONSOLE_OVERWRITE_ROUTINE.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:55 +01:00
Heiko Schocher
ccc7595a81 imx6: aristainetos: prepare dts for other board versions
as we switch to support DM and DTS, rework the existing
DTS trees. Change also Linux specific Device trees, goal
is to push this changes to linux.

Collect U-Boot specific changes in separate "*u-boot*" dts
files.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:55 +01:00
Heiko Schocher
8fb028ee20 imx6: aristainetos: add device tree from linux
Add device trees from Linux in preparation for driver model
conversions.

device tree files taken from Linux:
71ae5fc87c34: "Merge tag 'linux-kselftest-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest"

and added SPDX license identifier.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:55 +01:00
Heiko Schocher
1b857f1a92 imx6: aristainetos: remove 2b version
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:55 +01:00
Heiko Schocher
3882e6fc01 imx6: aristainetos: move defines to Kconfig
move defines, which are already moved to Kconfig
out of board config.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:55 +01:00
Heiko Schocher
a7e2dc9cf6 imx6: remove aristainetos board
remove not anymore used aristainetos board.

Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07 10:26:55 +01:00
Tom Rini
5a8fa095cb Merge branch 'next'
Bring in the following merges:

commit 8fbbec12f7
Merge: 87f69f467a 63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date:   Fri Jan 3 09:48:47 2020 -0500

    Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next

    - updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support

commit 87f69f467a
Merge: c0912f9bbf 4466b99703
Author: Tom Rini <trini@konsulko.com>
Date:   Tue Dec 24 08:18:19 2019 -0500

    Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next

    - Enable DM driver on ppc/km boards
    - Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
      T104x, P4080, P2041, P2020, P1020, P3041
    - Some updates in mpc85xx-ddr driver, km boards

commit c0912f9bbf
Merge: 533c9f5714 a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date:   Wed Dec 18 07:20:19 2019 -0500

    Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next

    - Various x86 common codes updated for TPL/SPL
    - I2C designware driver updated for PCI
    - ICH SPI driver updated to support Apollo Lake
    - Add Intel FSP2 base support
    - Intel Apollo Lake platform specific drivers support
    - Add a new board Google Chromebook Coral

commit 533c9f5714
Merge: 553cb06887 033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date:   Tue Dec 17 07:53:08 2019 -0500

    Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next

    i2c: for next
    - misc: i2c_eeprom:
      Add partition support and add ability to query size
      of eeprom device and partitions
    - i2c common:
      add support for offset overflow in to address and add
      sandbox tests for it.

commit 553cb06887
Merge: f39abbbc53 b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date:   Thu Dec 12 08:18:59 2019 -0500

    Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next

    buildman improvements including toolchain environment feature
    sandbox unicode support in serial
2020-01-06 17:07:49 -05:00
Lokesh Vutla
40109f4d7e arm: mach-k3: Enable WA for R5F deadlock
On K3 devices there are 2 conditions where R5F can deadlock:
1.When software is performing series of store operations to
  cacheable write back/write allocate memory region and later
  on software execute barrier operation (DSB or DMB). R5F may
  hang at the barrier instruction.
2.When software is performing a mix of load and store operations
  within a tight loop and store operations are all writing to
  cacheable write back/write allocates memory regions, R5F may
  hang at one of the load instruction.

To avoid the above two conditions disable linefill optimization
inside Cortex R5F which will make R5F to only issue up to 2 cache
line fills at any point of time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-03 09:47:11 -05:00
Lokesh Vutla
196d3e4017 arm: dts: k3-j721e: ddr: Update to 0.2 version of DDR config tool
Update the ddr settings to use the DDR reg config tool rev 0.2.0.
This reduces the aging count(in DDRSS_CTL_274_DATA reg) to 15 in-order
to avoid DSS underflow errors.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
2020-01-03 09:47:10 -05:00
Tom Rini
28aa6dc29a Merge tag 'u-boot-rockchip-20191231' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
2020-01-02 10:28:26 -05:00
Robert P. J. Day
e852b30b23 arch/arm/Kconfig: typo/grammar/punctuation fixes
Various (mostly minor) spelling, grammar and punctuation tweaks for
arch/arm/Kconfig.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2020-01-02 10:27:23 -05:00
Pankaj Bansal
ba7c966c0f pci: layerscape: move PCIE related CONFIG to PCI Kconfig
move the PCIE related config from arch Kconfig to PCI Kconfig.
As the PCI_LAYERSCAPE driver is being used in platform other than
fsl-layerscape platforms like ls102xa.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-02 14:36:57 +05:30
Kever Yang
fa2047c473 rockchip: rk3328: enable spl-fifo-mode for emmc and sdmmc
Since mmc to sram can't do dma, add patch to prevent aborts transfering
TF-A parts.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-31 15:57:55 +08:00
Tom Rini
6cb87cbb14 Fixes for 2020.01
-----------------
 - Fixes for Nitrogen6x
 - Fix corruption for mx51evk
 - colibri i.MX6: fix broken ESDHC conversion
 - mx6sxsabresd: fix broken mmcdev
 - imx6q_logic: cleanup boot sequence
 - update ATF for imx8mq_evk
 - pfuze: fix pmic_get()
 
 Travis CI: https://travis-ci.org/sbabic/u-boot-imx/builds/630007464
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl4HLywPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3cB0L/jRElnVFGaZC6Bii7jVS9u/oJ03yYM73Qp4M
 AWlITWIHQtB6PAGBVYz+Ts17grkYWT5fwuV3TqE+yfOeeD76cfo37L9iSePIQ7mC
 SYWfId3E3xz++2/64HM1PETWmPXi76QxeJ4GMP9amZMLW+huS6sWi1tfVEURedl0
 LXddxpa4DkjMeU4sKLgrGLv3+wIu5P6ELcpQXrBQs7uVQxiwvWh3rrldHlLzacHm
 o2DUE4rDrtN5K2khT/Gq9wf7eG1vCbIKFvDTTFjgkg5nlfeeiiEHXqAKiLN/hPmq
 BrrxBXucPqUj9V/tozcBMrQ6bFfGkaGaBUVT8AqBWe/CUKaicrcxZLh1Ef18fo0y
 yxh3RfnW6kYIokRxP4uf9kRXxip7hYciqlvhHdO7pY6TkwweuzFVvUmlKD6dCS9z
 iulDyZfAXNXYxtEFqBBO7A2bQo5u9MqR7xYjNc3aALOeXt8H+wcM7BQZ1ga72d2X
 nNw1XHR84Kjr/lc5PJRVp/Nz9s4VVw==
 =GLWM
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191228' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

Fixes for 2020.01
-----------------
- Fixes for Nitrogen6x
- Fix corruption for mx51evk
- colibri i.MX6: fix broken ESDHC conversion
- mx6sxsabresd: fix broken mmcdev
- imx6q_logic: cleanup boot sequence
- update ATF for imx8mq_evk
- pfuze: fix pmic_get()

Travis CI: https://travis-ci.org/sbabic/u-boot-imx/builds/630007464
2019-12-28 08:07:16 -05:00
Troy Kisky
61d7e2bcc7 ARM: i.MX6: TARGET_NITROGEN6X: add 'select MX6QDL'
This fixes commit <91435cd40d30> "ARM: i.MX6: exclude the ARM errata
 from i.MX6 UP system"

for nitrogen6x. The above commit removed the errata for the board
since MX6Q/MXDL/MX6S is selected via CONFIG_SYS_EXTRA_OPTIONS

This restores the errata configs.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-12-27 14:28:42 +01:00
Jorge Ramirez-Ortiz
e97bdfa5da tools/imximage: share DCD information via Kconfig
IMX based platforms can have the DCD table located on different
addresses due to differences in their memory maps (ie iMX7ULP).

This information is required by the user to sign the images for secure
boot so continue making it accessible via mkimage.

Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-12-27 12:55:59 +01:00
Thomas Hebb
d4e4187b8c rockchip: add description for TPL_ROCKCHIP_COMMON_BOARD
SPL_ROCKCHIP_COMMON_BOARD, an almost identical option, has a title but
this one doesn't for some reason. Add a description to make the menu
easier to read.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-27 14:26:13 +08:00
Kever Yang
3176d47d35 rockchip: px30-firefly add standalone dts
Firefly Core-PX30-JD4 use UART2M1 while PX30 evb using UART2M0, the U-Boot
proper will use the dts setting to do the IOMUX init, and a separate dts
is needed for px30-firefly.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-27 14:26:13 +08:00
Jack Mitchell
6d06ea3423 rockchip: make_fit_atf: explicitly use python3
On a distribution with no python2 installed and no
python->python3 symlink the script will fail to execute.
Specify python3 explicitly as it's already a requirement
to build u-boot.

Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-27 14:26:13 +08:00
Kever Yang
7c337710fc rockchip: fit_spl_optee: get text and optee base from build
Instead of hardcode the base address, we can get them from the build
output, eg. get the SYS_TEXT_BASE from .config and get optee base from
DRAM_BASE.
We can use this script for SoCs with DRAM base not from 0x60000000(rk3229
and many other 32bit Rockchip SoCs), eg. rk3288 DRAM base is 0.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-26 20:34:28 +08:00
Wasim Khan
7cd4272821 armv8: lx2160a: Add FSL_PEX_STREAM_ID_END for LX2160A
Add FSL_PEX_STREAM_ID_END and remove FSL_PEX_STREAM_ID_NUM
for lx2160a.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:21 +05:30
Kuldeep Singh
ce3bead608 fsl-lsch3: soc: Enable AHB read support for Flexspi controller
Enable AHB support for Flexspi controller interface meaning
memory can be accessed via md command using absolute addresses

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Kuldeep Singh
0b6c3706ab fsl-lsch3: Add FlexSPI address space in immap_lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
2019-12-26 16:00:20 +05:30
Alex Marginean
3499dd033c ls1028a: Configure stream IDs for integrated PCI and fix up Linux DT
Hardware comes out of reset with implicit values, but these are outside
the accepted range for Layerscape gen 3 chassis spec used on LS1028A.
Allocate different IDs and fix up Linux DT to use them.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Vabhav Sharma
c1ead04bc4 arm64: lx2160a: dts: Fix UART node status
LX2160A PL011 UART driver fetch IP block values using
platform data from board file instead of device tree.

Modified UART nodes in device tree to disable state.

Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Ran Wang
0cfa00cdb9 armv8: Add workaround for USB erratum A-050106
USB3.0 Receiver needs to enable fixed equalization
for each of PHY instances in an SOC. This is similar
to erratum A-009007, but this one is for LX2160A,
and the register value is different.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Michael Walle
055aa33ff9 armv8: layerscape: fix SPL multi DTB loading
Mark board_fit_config_name_match() as weak so a board can overwrite the
empty function.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Heinrich Schuchardt
421e7a41c6 sunxi: remove __packed from struct sunxi_prcm_reg
struct sunxi_prcm_reg is naturally packed. There is no need to define it as
packed. Defining it as packed leads to compilation errors with GCC 9.2.1:

  CC      arch/arm/lib/reloc_arm_efi.o
arch/arm/cpu/armv7/sunxi/psci.c: In function ‘sunxi_cpu_set_power’:
:qarch/arm/cpu/armv7/sunxi/psci.c:163:21: error: taking address of packed
member of ‘struct sunxi_prcm_reg’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
  163 |  sunxi_power_switch(&prcm->cpu_pwr_clamp[cpu], &prcm->cpu_pwroff,
      |                     ^~~~~~~~~~~~~~~~~~~~~~~~~

Remove __packed attribute from struct sunxi_prcm_reg.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-12-18 20:19:58 +05:30
Diego Rondini
e7c15b7ab8 sun8i: h3: Support H3 variant of Orange Pi Zero Plus 2
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.

H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply

Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.

Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-12-18 20:14:16 +05:30
Heinrich Schuchardt
9bd34a69a4 sunxi: psci: avoid error address-of-packed-member
Compiling with GCC 9.2.1 leads to build errors:

arch/arm/cpu/armv7/sunxi/psci.c: In function ‘sunxi_cpu_set_power’:
arch/arm/cpu/armv7/sunxi/psci.c:144:21: error: taking address of packed
member of ‘struct sunxi_cpucfg_reg’ may result in an unaligned pointer
value [-Werror=address-of-packed-member]
  144 |  sunxi_power_switch(&cpucfg->cpu1_pwr_clamp, &cpucfg->cpu1_pwroff,
      |                     ^~~~~~~~~~~~~~~~~~~~~~~
arch/arm/cpu/armv7/sunxi/psci.c:144:46: error: taking address of packed
member of ‘struct sunxi_cpucfg_reg’ may result in an unaligned pointer
value [-Werror=address-of-packed-member]
  144 |  sunxi_power_switch(&cpucfg->cpu1_pwr_clamp, &cpucfg->cpu1_pwroff,
      |                                              ^~~~~~~~~~~~~~~~~~~~

Use memcpy() and void* pointers to resolve the problem caused by packing
the struct sunxi_cpucfg_reg.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-12-18 20:13:34 +05:30
Patrick Delaunay
16fec9b0bc stm32mp1: remove the imply BOOTSTAGE
This patch is only a temporarily workaround for crash introduced by
commit ac9cd4805c ("bootstage: Correct relocation algorithm").

The crash occurs because the bootstage struct is not correctly aligned
when BOOTSTAGE feature is activated.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-12-18 11:58:36 +01:00
Patrick Delaunay
eee15806fc stm32mp1: imply CMD_CLS
Activate by default the command CLS (clear screen);
this command used in pxe or sysboot command (DISTRO support)
when the "menu background" keyword is present.

This patch avoid the warning "Unknown command 'cls'"
with extlinux.conf:

# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
MENU BACKGROUND /splash.bmp
TIMEOUT 20
DEFAULT stm32mp157c-ev1-emmc
LABEL stm32mp157c-ev1-emmc
	KERNEL /uImage
	FDT /stm32mp157c-ev1.dtb
	APPEND root=/dev/mmcblk1p4 rootwait rw console=ttySTM0,115200

  ...
  Retrieving file: /mmc0_stm32mp157c-ev1_extlinux/extlinux.conf
  614 bytes read in 36 ms (16.6 KiB/s)
  Retrieving file: /splash.bmp
  46180 bytes read in 40 ms (1.1 MiB/s)
  Unknown command 'cls' - try 'help'
  Select the boot mode
  1:	stm32mp157c-ev1-sdcard
  ...

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-12-18 11:52:35 +01:00
Tudor Ambarus
f10b4006a6 board: atmel: sama5d27_wlsom1_ek: Set ethaddr from spi-nor flash
The SST26VF064BEUI spi-nor flash is programmed at the factory with a
globally unique address stored in the SFDP vendor parameter table and
it is permanently writeprotected. Retrieve the EUI-48 address and set it
as ethaddr env.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-12-17 09:49:05 +02:00
Simon Glass
bcee8d6764 dm: gpio: Allow control of GPIO uclass in SPL
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.

Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.

Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.

This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-15 08:52:29 +08:00
Hannes Schmelzer
05767707a8 dts: am335x-brsmarc1/xre1: insert phy_id again
commit 3b3e8a37d3
("arm: dts: am335x: sync cpsw/mdio/phy with latest linux - drop phy_id")

did sync with recent linux kernel and replaced therefore the 'phy_id'
property with a phy-handle pointing to the mdio.

This is OK for linux, but introduces trouble with the already running
vxWorks on this target.

So this commit here re-inerts the phy_id property beside the phy-handle
property to be compatible with both.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-12-13 13:01:12 -05:00
Suman Anna
1045ff4d1a ARM: DRA7: Fixup DSP OPP_HIGH clock rate on DRA76P/DRA77P SoCs
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") added the core logic to update the kernel
device-tree blob to adjust the DSP, IVA and GPU DPLL clocks based on
a one-time OPP choice selected in U-Boot for most of the DRA7xx/AM57xx
family of SoCs.

The DSPs on DRA76xP/DRA77xP SoCs (DRA76x ACD package SoCs) though
provide a higher performance and can run at a higher clock frequency
of 850 MHz at OPP_HIGH instead of 750 MHz. Fix up the logic to use the
correct clock rates on these SoCs. Note that this higher clock rate is
not applicable to other Jacinto 6 Plus SoCs (DRA75xP/DRA74xP SoCs or
AM574x SoCs) that follow the ABZ package.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-12-09 14:00:24 -05:00
Tom Rini
ac1ca99926 Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-net 2019-12-09 13:48:22 -05:00
Vignesh Raghavendra
4886f1cb59 arm: dts: k3-j721e-common-proc-board: Add DMA and CPSW related DT nodes
Add DT nodes related to DMA and CPSW to -u-boot.dtsi to get networking
up on J721e EVM.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-12-09 09:47:43 -06:00
Nevo Hed
06f555274e arm: dts: armada-cp110-*dtsi: add xmdio nodes
Based on upstream-linux
See https://github.com/torvalds/linux/commit/f66b2aff.

However made the XSMI register window 0x16 (22) bytes per my reading
of the functional spec.  Similar commits in Marvels own repo bump it
to 0x200 (512) bytes but I did not see the reasoning for that.

https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/4d932b4.

Also added device-name attributes to prevent ambiguity in the `mdio`
command.

Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
5efb69298b arm: dts: k3-am654-base-board-u-boot: change cpsw2g interface mode to rgmii-rxid
The AM654 SoC doesn't allow to disabling RGMII TX internal delay in CPSW2G
MAC. Hence, change CPSW2G interface mode to "rgmii-rxid" - RGMII with
internal RX delay provided by the PHY, the MAC will add an TX delay in this
case.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Joe Hershberger
fb8977c5be net: Always build the string_to_enetaddr() helper
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.

Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
2019-12-09 09:47:41 -06:00
Heinrich Schuchardt
0c5c3f2935 arm: -march=armv5t for ARM11
In GCC 9 support for the Armv5 and Armv5E architectures (which have no
known implementations) has been removed, cf.
https://gcc.gnu.org/gcc-9/changes.html

Commit 16540d07fd ("arm: fix -march for ARM11") changed the value of the
compiler flag from -march=armv5 and -march=armv5t into -march=armv6 for
ARM11.

The values prior to this patch were:

    arch-$(CONFIG_CPU_ARM1136)     =-march=armv5
    arch-$(CONFIG_CPU_ARM1176)     =-march=armv5t

The change lead to a regression with the Raspberry Pi Zero W not booting
anymore.

Use -march=armv5t both for ARM1136 and ARM1176.

Fixes: 16540d07fd ("arm: fix -march for ARM11")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Joris Offouga <offougajoris@gmail.com>
2019-12-09 10:36:00 -05:00
Tom Rini
2f02845817 Fixes for 2020.01
-----------------
 
 - imx8qxp_mek: increase buffer sizes and args number
 - Fixes for imx7ulp
 - imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
 - colibri_imx7: reserve DDR memory for Cortex-M4
 - vining2000: fixes and convert to ethernet DM
 - imx8m: fix rom version check to unbreak some B0 chips
 - tbs2910: Disable VxWorks image booting support
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl3uLqsPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3YEEL/jAKMnREGNHCjvwvxkVVZ7sWHeRtqh+OXb8V
 VnZB0glptth1NDxWyHFZkcsVqjpRlUsm3/lA91xaFXcUB8EWnJMKVReHkB7v0bZW
 zHziN0rNPoTBVocRlpgPXt3zeSOR3Qg+rFesg4zmlXNIVPyvBanpDCxXDK60gdIi
 JDrAdIarP0UMK0roIFLIyvnJ+J/ib1ky1aJI8cdktXb+nSyVrMw5VDdmSBtTCp10
 6o/fJGtWfzXp59a8y9XnnVxNsU2c0URcsswub4fvWhhwJ86xiWGSEfm5Sybql6kS
 6PYjB7jGmdWJjYug7rFthl1Hnn1FULIH9qrxPePtD2ooUUjHPlDmElQqWkHoVlib
 yUAlWG87ZdjhmEMR1iSFlkcBpOD7SlmcvfYZdeedCdtzTwW0kj6lcX9fUKHE+17e
 3SJQtPxpMrVfnUDRn0ciAbwg8+1Tow6sv39j6iYi7jAITny9q16ErdRGup0wB19Y
 tZkmRdnhtjCalrfDoEaRGXZJDE15XQ==
 =L2zo
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

Fixes for 2020.01
-----------------

- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
2019-12-09 10:32:08 -05:00
Patrick Wildt
6a4b07e086 imx8m: fix rom version check to unbreak some B0 chips
Recently the version check was improved to be able to determine that
we're running on SoC revision 2.1.  A check for B0 was tightened so
that it now must equal 0x20 instead of being bigger than 0x20.  On
some B0 chips the value returned is 0x1020 instead of 0x20.  This
means even though it's B0, the check will fail and code relying on
the correct chip revision will make wrong decisions.  There is no
documentation of those bits, but it seems that NXP always uses a
byte to encode the revision.  Thus remove the upper bits to fix the
regression.

Signed-off-by: Patrick Wildt <patrick@blueri.se>
2019-12-09 11:52:06 +01:00
Tom Rini
bead4f2f2c Merge tag 'u-boot-rockchip-20191206' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
2019-12-06 10:35:18 -05:00
Marek Vasut
edaec53212 ARM: imx: vining2000: Repair PCIe support
Ever since the conversion to DM PCI, the board was missing the PCIe DT
nodes, hence the PCI did not really work. Fill in the DT nodes and add
missing PCIe device reset.

Moreover, bring the PCIe power domain up before booting Linux. This is
mandatory to keep old broken vendor kernels working, as they do not do
so and depend on the bootloader to bring the power domain up.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-12-06 13:57:42 +01:00
Marek Vasut
7d84f4469f ARM: imx: vining2000: Convert to SPL framework
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-12-06 13:57:42 +01:00
Marek Vasut
df1b721f60 ARM: mx6: pmu: Expose PMU LDO configuration interface
Make the PMU LDO configuration interface available to board code,
so that board code can reconfigure the internal LDOs of the SoC.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
2019-12-06 13:57:42 +01:00
Igor Opaniuk
c671d8af0b board: colibri_imx7: reserve DDR memory for Cortex-M4
i.MX 7's Cortex-M4 core can run from DDR and uses DDR memory for
the rpmsg communication. Both use cases need a fixed location of
memory reserved. For the rpmsg use case the reserved area needs
to be in sync with the kernel's hardcoded vring descriptor location.

Use the linux,usable-memory property to carve out 1MB of memory
in case the M4 core is running. Also make sure that the i.MX 7
specific rpmsg driver does not get loaded in case we do not carve
out memory.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-12-06 12:09:30 +01:00
Fabio Estevam
d396f1384c mx6: Allow configuring the NoC registers on i.MX6QP
The NoC registers on i.MX6QP needs to be configured, otherwise some
usecases in the kernel behave incorrectly, such as rotation and resize.

Currently the NoC registers are not configured in the kernel, so
configure them in U-Boot like it is done in the NXP U-Boot tree.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2019-12-06 12:09:25 +01:00
Fabio Estevam
2d4b87f867 mx7ulp: Sync the device tree related files
Sync the mx7ulp device tree related files with the one from
NXP U-Boot vendor tree (imx_v2019.04_4.19.35_1.0.0).

The mainline support for i.MX7ULP is very premature at this stage.

We should probably re-sync with mainline Linux dts when it gets
in better shape, but for now sync with the U-Boot vendor code.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-12-06 12:05:08 +01:00
Fabio Estevam
d136eb9bfe mx7ulp: scg: Remove unnused scg_a7_apll_init()
scg_a7_apll_init() is not called anywhere, so remove such dead code

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-12-06 12:05:08 +01:00
Fabio Estevam
0619af0942 mx7ulp: Remove the _RUN notation from the PMC1 LDOVL definitions
The LDOVL definitions is common to all the modes, not only RUN mode,
so in order to avoid confusion, remove the _RUN notation from the PMC1
LDOVL definitions.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-12-06 12:05:08 +01:00
Fabio Estevam
b8cabb0e3d mx7ulp: Introduce the CONFIG_LDO_ENABLED_MODE option
Introduce the CONFIG_LDO_ENABLED_MODE option so that i.MX7ULP boards
designed to operate with LDO enabled mode can work with 0.95V at LDO
output in RUN mode as per the datasheet.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-12-06 12:05:08 +01:00
Fabio Estevam
72a093a8ac mx7ulp: Print the LDO mode status
As per the i.MX7ULP datasheet, it can boot in LDO enabled mode
or LDO bypass mode.

Print the LDO mode status in the U-Boot log for convenience.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-12-06 12:05:08 +01:00
David Wu
e0e6c96a67 arm: rockchip: rk3308: Initialize the iomux configuration
When we want to use plus pinctrl feature, we need to enable
them at spl.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
David Wu
4ee6d51c5a pwm: rk_pwm: Make PWM driver to support all Rockchip Socs
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.

The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.

The RK3288 keep the current functions.

RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
David Wu
aebd9eddb3 dts: rk3308: Enable ethernet function supported for Firefly ROC_RK3308_CC
The Firefly ROC_RK3308_CC use ref_clock of input mode,
and rmii pins of m1 group.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
David Wu
982fab393d arm: dts: Add mac node for rk3308 at dtsi level
The rk3308 only support RMII mode, and if it is output clock
mode, better to use ref_clk pin with drive strength 12ma.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
Heiko Stuebner
fd3a7ae8e6 rockchip: misc: protect serial# from getting overwritten
serial# is one of the vendor properties and thus protected from being
overwritten if already set. If env_set is called anyway this result in
some nasty warnings, so check for presence before trying that.

In the same direction check for the presence of cpuid# and compare it
to the actual hardware and emit a warning if they don't match.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-05 23:53:07 +08:00
Heiko Stuebner
d490fadc70 rockchip: misc: don't fail if eth_addr already set
rockchip_setup_macaddr() runs from an initcall, so returning an error
code will make that initcall fail thus breaking the boot process.

And if an ethernet address is already set this is definitly not a
cause for that, so just return success in that case.

Fixes: 0482538499 ("rockchip: rk3399: derive ethaddr from cpuid");
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-05 23:53:07 +08:00
Paul Kocialkowski
c541bfda2f rockchip: px30: Add support for using UART3 as debug UART
Some generic PX30 SoMs found in the wild use UART3 as their debug output
instead of UART2 (used for MMC) and UART5.

Make it possible to use UART3 as early debug output, with the associated
clock and pinmux configuration. Two sets of output pins are supported (M0/M1).

Future users should also note that the pinmux default in the dts is to use
the M1 pins while the Kconfig option takes M0 as a default.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
2019-12-05 23:53:07 +08:00
Paul Kocialkowski
ec4fafdf1f rockchip: px30: Rename CONFIG_DEBUG_UART2_CHANNEL to CONFIG_DEBUG_UART_CHANNEL
UART3 also has two sets of pins that can be selected.

Rename the config option to a common name, to allow it to be used for both
UART2 and UART3.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-05 23:53:07 +08:00
Paul Kocialkowski
b0c5e37d0e rockchip: px30: Fixup PMUGRF registers layout order
According to the PX30 TRM, the iomux registers come first, before the pull
and strength control registers.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
2019-12-05 23:53:07 +08:00
Andy Yan
afe18f205e rockchip: px5: enable spl-fifo-mode for emmc for px5-evb
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-05 23:53:07 +08:00
Andy Yan
081a51c937 rockchip: rk3308: enable spl-fifo-mode for emmc
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.

And show my best respect to Heiko's work for this solution.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-05 23:53:07 +08:00
Thomas Hebb
9f67b56772 Fix typo in macros, "FIRMEWARE" -> "FIRMWARE"
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
2019-12-05 10:28:39 -05:00
Miquel Raynal
eb446ef625 cmd: nand/sf: isolate legacy code
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.

This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
mingming lee
abf2c68566 ARM: MediaTek: add basic support for MT8518 boards
This adds a general board file based on MT8518 SoCs from MediaTek.

Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.

This commit is adding the basic boot support for the MT8518 eMMC board.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 12:00:03 -05:00
mingming lee
485627dd5f pinctrl: add driver for MT8518
Add Pinctrl driver for MediaTek MT8518 SoC.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2019-12-03 08:44:14 -05:00
mingming lee
13e89d7522 ARM: MediaTek: Add support for MediaTek MT8518 SoC
Add support for MediaTek MT8518 SoC. This include the file
that will initialize the SoC after boot and its device tree.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2019-12-03 08:44:14 -05:00
Bartosz Golaszewski
598d9bccc5 board: omapl138_lcdk: add the mmc device to SPL
We don't have full device-tree support in SPL yet - add an appropriate
U_BOOT_DEVICE() to the board file.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:14 -05:00
Bartosz Golaszewski
6a97153cbf mmc: davinci: drop support for ti,dm6441-mmc
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:13 -05:00
Giulio Benetti
1b3d24b735 armv7m: cache: add invalidate_icache_all() stub
This commit:
d409c96216
causes build failure with ICACHE enabled. This is due to missing
invalidate_icache_all() stub. Let's add empty invalidate_icache_all() in
the case where ICACHE is not enabled.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2019-12-03 08:43:24 -05:00
Thomas Hebb
32f2ca2a7e cosmetic: Fix spelling and whitespace errors
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
2019-12-03 08:43:23 -05:00
Simon Glass
5255932f01 common: Move some board functions out of common.h
A number of board function belong in init.h with the others. Move them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:21 -05:00
Simon Glass
67c4e9f815 common: Move board_get_usable_ram_top() out of common.h
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:04 -05:00
Simon Glass
288b29e44d common: Move command functions out of common.h
Move these functions into the command.h header file which is a better fit.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:02 -05:00
Simon Glass
36bf446b64 common: Move enable/disable_interrupts out of common.h
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:01 -05:00
Simon Glass
c30b7adbca common: Move interrupt functions into a new header
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.

Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:00 -05:00
Simon Glass
9d3915b2df arm: powerpc: Tidy up code style for interrupt functions
Remove the unwanted space before the bracket.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:24:59 -05:00
Simon Glass
1eb69ae498 common: Move ARM cache operations out of common.h
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:24:58 -05:00
Simon Glass
9edefc2776 common: Move some cache and MMU functions out of common.h
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.

Move them over.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:55 -05:00
Simon Glass
6cc915b5fb arm: powerpc: Tidy up code style for cache functions
Remove the unwanted space before the bracket.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:14 -05:00
Simon Glass
62270f4395 common: Move some SMP functions out of common.h
These functions belong in cpu_func.h so move them over.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:14 -05:00
Simon Glass
b5981474f1 common: Move some CPU functions out of common.h
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:13 -05:00
Simon Glass
68a6aa85ec common: Move mii_init() function out of common.h
This function belongs in mii.h so move it over.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:13 -05:00
Simon Glass
1045315df0 common: Move get_ticks() function out of common.h
This function belongs in time.h so move it over and add a comment.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:13 -05:00
Simon Glass
e3107d159c arm: pxa: Drop pxa_wait_ticks()
This function has a similar name to the common wait_ticks(). It is only
used in one place and seems small enough to drop.

Inline it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:11 -05:00
Simon Glass
6887c5bed9 common: Move some time functions out of common.h
These functions belong in time.h so move them over and add comments.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:11 -05:00
Simon Glass
b03e0510d7 common: Move serial functions out of common.h
These functions belong in serial.h so move them over.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:11 -05:00
Simon Glass
2189d5f1e8 Move strtomhz() to vsprintf.h
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.

Use the vsprintf.h include file explicitly where needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:09 -05:00
Simon Glass
3db7110857 crc32: Use the crc.h header for crc functions
Drop inclusion of crc.h in common.h and use the correct header directly
instead.

With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:08 -05:00
Simon Glass
62f9b65447 common: Move older CPU functions to their own header
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:06 -05:00
Tom Rini
dd38416d6b Merge git://git.denx.de/u-boot-socfpga
- Assorted Gen5 fixes
2019-11-28 07:34:41 -05:00
Tom Rini
089612da33 Merge tag 'mmc-11-27-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- fsl_esdhc update and some cleanup in ls1021a/mpc83xx code
- mmc tmio sdhi update for hs400
2019-11-28 07:33:45 -05:00
Yangbo Lu
d3eb317ea5 arm: drop eSDHC clock getting in mxc_get_clock() for layerscape
Although layerscape platforms reuse mxc_get_clock() of i.MX platforms,
eSDHC clock getting do not have to use it. It uses global data
gd->arch.sdhc_clk directly in fsl_esdhc driver. Even there are more
than one eSDHC controllers on SoC, they use same reference clock.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-27 16:55:56 +08:00
Patrick Delaunay
4d7d0e2e78 ARM: dts: stm32: update eMMC configuration for stm32mp157c-ev1
Update the sdmmc2 node for eMMC support on eval board stm32mp157c-ev1.
- update slew-rate for pin configuration
- update "vqmmc-supply"
- remove "st,sig-dir"
- add mandatory "pinctrl-names"
- add "mmc-ddr-3_3v"

This patch solve the eMMC detection issue for command "mmc dev 1".

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-11-26 10:11:48 +01:00
Patrick Delaunay
62d620c243 ARM: dts: stm32: DT alignment with kernel v5.4-rc4
Device tree and binding alignment with kernel v5.4-rc4

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-11-26 10:11:48 +01:00
Patrick Delaunay
e07a86b5e3 ARM: dts: stm32: DT alignment with kernel v5.3
Device tree and binding alignment with kernel v5.3
and converted to SPDX.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-11-26 10:11:48 +01:00
Tom Rini
4b19b89ca4 - add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
 - add support for one binary on RPi3/4
 -----BEGIN PGP SIGNATURE-----
 
 iQJGBAABCAAwFiEEUdvKHhzqrUYPB/u8L21+TfbCqH4FAl3a8R4SHG1icnVnZ2Vy
 QHN1c2UuY29tAAoJEC9tfk32wqh+AfQP/iO4qiJWUsY1WgChKl0wZNnkJKViNu6v
 F7zczCIUyI7krdVb3E3PB/ZJwXY/ay1rQeY91cU/9f0Z3yOlsoiwnEfOT/HwwkmD
 KnS6nhisqL0W1yd8sK8XaLOydIFfe05Do1UvF1JhOl3061R81fdruXygkHlgFXiK
 /hrEXLb9l0Zf4XMSD9hQJZiC/K3qeUZV1KsEdSGArjjTj3kivvS++Z0XD1YZsBVs
 rsEl3ZhPeUmzAxmg26IfyJan02NjWY+MyuoSd8QW5kVGsF4WOgvDuBOY1YJ08C/7
 NhLGkub/XhqHVSaMDwiSoX9d2z7ZqTaw7+IZW38+fCMUFAEHiErqMDq+Zfk1DKCd
 WynOzMj6k+Kli+amHQMHuUqIY54XPwpXdn671C7XbQ8xWh7HhWH/sEHP7ekrSV74
 Et7dy5fcleCcrr8EDhdC5iO2fLKhswq4iT0PbnFMtha4jhPqFVHVaAZDacucJ1/V
 JpfYRkLrmEbva3G1emve80tzlDNDxjraX8G6/6trN+F0xjorcbImp64RtRjgdL62
 DwIuba15BGR18LQJY/yHSHT4h3ReEG5qF9vxX+r6vMiFACZbnBPAP/b/REDQ6LWs
 dwW01JQ343dmZiegBQOe98fRDMGhmTd52mAJ/8p60X+byIh5I4XFKCdEdUpSVBpK
 ARrdtg9vtLxv
 =4Z+A
 -----END PGP SIGNATURE-----

Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot

- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
2019-11-25 12:56:27 -05:00
Marek Vasut
a1a9843a29 ARM: socfpga: Unreset NAND in SPL on Gen5
In case the SPL on Gen5 loads U-Boot from NAND, unreset the NAND IP
explicitly in the platform code as the denali-spl driver is not aware
of DM at all.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-25 13:12:56 +01:00
Marek Vasut
2007a730ee ARM: socfpga: Add ArriaV ST/SX ID
Add new FPGA ID for ArriaV ST/D3 or SX/B3 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-25 13:12:56 +01:00
Marek Vasut
97a72bc286 ARM: socfpga: Purge pending transactions upon enabling bridges on Gen5
On Gen5, when the FPGA is loaded and there was some prior interaction
between the HPS and the FPGA via bridges (e.g. Linux was running and
using some of the IPs in the FPGA) followed by warm reset, it has been
observed that there might be outstanding unfinished transactions. This
leads to an obscure misbehavior of the bridge.

When the bridge is enabled again in U-Boot and there are outstanding
transactions, a read from within the bridge address range would return
a result of the previous read instead. Example:
=> bridge enable ; md 0xff200000 1
ff200000: 1234abcd
=> bridge enable ; md 0xff200010 1
ff200010: 5678dcba <------- this is in fact a value which is stored in
                            a memory at 0xff200000
=> bridge enable ; md 0xff200000 1
ff200000: 90effe09 <------- this is in fact a value which is stored in
                            a memory at 0xff200010
and so it continues. Issuing a write does lock the system up completely.

This patch opens the FPGA bridges in 'bridge enable' command, the tears
them down again, and then opens them again. This allows these outstanding
transactions to complete and makes this misbehavior go away.

However, it is not entirely clear whether this is the correct solution.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-25 13:12:56 +01:00
Marek Vasut
446cf811c5 ARM: socfpga: Actually put bridges into reset on Gen5 in bridge disable
On Gen5, the 'bridge disable' command write 0x0 to brgmodrst register,
which releases all bridges from reset, instead of putting all bridges
into reset. Fix this by inverting the mask and actually putting the
bridges into reset.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-25 13:12:55 +01:00
Matthias Brugger
5694090670 ARM: defconfig: add unified config for RPi3 and RPi4
Provide a defconfig which allows us to boot Raspberrry Pi 4
and Raspberry Pi 3 Model B/B+
Instead of using the embedded DTB as done in RPi3 we use the
devicetree provided by the firmware.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:28 +01:00
Matthias Brugger
917a1e9a78 ARM: bcm283x: Set memory map at run-time
For bcm283x based on arm64 we also have to change the mm_region.
Add assign this in mach_cpu_init() so we can create now one binary
for RPi3 and RPi4.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:28 +01:00
Matthias Brugger
dd47ca7873 ARM: bcm283x: Set rpi_bcm283x_base at run-time
As part of the effort to create one binary for several bcm83x SoCs
we read the IO base address from device-tree.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:27 +01:00
Matthias Brugger
8e3361c88a ARM: bcm283x: Move BCM283x_BASE to a global variable
We move the per SOC define BCM283x_BASE to a global variable.
This is a first step to provide a single binary for several bcm283x
SoCs.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:27 +01:00
Matthias Brugger
5051377a0b arm: dts: bcm283x: Rename U-Boot file
Rename the file bcm283x-uboot.dtsi so that it get
automatically include through the scripts/Makefile.lib
using $(CONFIG_SYS_SOC))-u-boot.dtsi

Without this uarts and pincontroller miss the property dm-pre-reloc
and the first call to bcm283x_mu_serial_ofdata_to_platdata() fails
as the pins are not set correctly.
As a result the U-Boot banner isn't shown on boot.

Before commmit
143256b353 ("fdt: update bcm283x device tree sources to Linux 5.1-rc6 state")
we included bcm283x-uboot.dtsi directly in the device-tree file.
Which got deleted by the metioned commit.
This is a much robuster solution.

Reported-by: Tom Rini <trini@konsulko.com>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com> [RPi 3, 32b and 64b modes]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:27 +01:00
Matthias Brugger
89e47e8eb6 fdt: fix bcm283x dm-pre-reloc definitions
In commmit
143256b353 ("fdt: update bcm283x device tree sources to Linux 5.1-rc6 state")
we deleted the label for the node soc from bcm283x.dtsi

As we don't need to add the property dm-pre-reloc to the soc node,
we can delete it from bcm283x-uboot.dtsi

Tested-by: Tom Rini <trini@konsulko.com> [RPi 3, 32b and 64b modes]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:27 +01:00
Tom Rini
9a0cbae22a Merge tag 'u-boot-rockchip-20191124' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
2019-11-23 20:50:11 -05:00
Heinrich Schuchardt
16540d07fd arm: fix -march for ARM11
In GCC 9 support for the Armv5 and Armv5E architectures (which have no
known implementations) has been removed, cf.
https://gcc.gnu.org/gcc-9/changes.html

ARM11 is an armv6 implementation. So change the architecture flag for the
compiler to armv6 for ARM11.

Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-11-23 14:53:48 -05:00
Heiko Stuebner
8019d32c47 rockchip: px30: enable spl-fifo-mode for both emmc and sdmmc on evb
As part of loading trustedfirmware, the SPL is required to place portions
of code into the socs sram but the mmc controllers can only do dma
transfers into the regular memory, not sram.

The results of this are not directly visible in u-boot itself, but
manifest as security-relate cpu aborts during boot of for example Linux.

There were a number of attempts to solve this elegantly but so far
discussion is still ongoing, so to make the board at least boot correctly
put both mmc controllers into fifo-mode, which also circumvents the
issue for now.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-11-23 23:41:44 +08:00
Jagan Teki
c618bb0042 rockchip: Setup dwc3_device (for non-dm gadgets)
Setup dwc3_device structure for non-dm gadgets, which is used
in rk3399 platforms.

dwc3_device would have basic regbase, dr_mode, high speed
and 16-bit UTMI+ etc.

Cc: Marek Vasut <marex@denx.de>
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix to use CONFIG_USB_DWC3_GADGET instead of CONFIG_USB_DWC3)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 23:41:44 +08:00
Kever Yang
65325fba5a rockchip: Convert to use FIT generator for optee
Use generator script so that we can use environment for TEE source.
$TEE for tee.bin, and if file not exist, the script can report a warning,
and meke the build success without a error.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Tom Rini
47b48fe186 Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Assorted fixes
2019-11-22 10:41:46 -05:00
Tom Rini
71d96eb99e Merge branch 'master' of git://git.denx.de/u-boot-sh
- Assorted Gen3 fixes
2019-11-22 10:24:14 -05:00
Ooi, Joyce
0c14bb5ad3 arm: socfpga: stratix10: Add alias for gmac0 in S10 dts
Add 'ethernet0' as alias for 'gmac0' in S10 device tree.

Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-22 03:08:12 +01:00
Ooi, Joyce
7dad444c76 arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver
The HPS EMAC0 drive strength is changed to 4mA because the initial 8mA
drive strength has caused CE test to fail. This requires changes on the
pad skew for EMAC0 PHY driver. Based on several measurements done, Tx
clock does not require the extra 0.96ns delay which was needed in
Arria10.

Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-22 03:08:12 +01:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Simon Goldschmidt
26fb85f4ab socfpga: fix include guard in misc.h (arch vs. global)
The file arch/arm/mach-socfpga/include/mach/misc.h used the same include
guard as the global include/misc.h.

Fix this by giving the arch file an arch prefix.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-20 22:32:00 +01:00
Ley Foon Tan
9184590d9a arm: dts: Stratix10: Fix memory node address and size cells
Add #address-cells and #size-cells to memory node to fix incorrect memory
size decoding in recent Uboot version.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-20 22:32:00 +01:00
Heinrich Schuchardt
d47a774680 arm: arm11: allow unaligned memory access
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.

This patch implements the function unaligned_access() to set the enable
unaligned data support flag and to clear the aligned flag in the system
control register (SCTLR). It is called when UEFI related commands like
bootefi are invoked.

Reported-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Tested-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Tested-by: Guillaume Gardet <Guillaume.Gardet@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-11-19 12:10:22 +01:00
Tom Rini
fffb826ea0 - fix i.MX6ULL evk black screen observed while reboot stress tests
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
   differences between Linux and U-Boot for stm32mp1 platform
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXdJyOg4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXOmuAJ9lF7GyPpv0vZNX1V4UV2EyyOOdbwCfQzHu3Xo+
 3VWLV9ZHkVMlfnGbbx0=
 =+YuG
 -----END PGP SIGNATURE-----

Merge tag 'video-for-v2020.01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-video

- fix i.MX6ULL evk black screen observed while reboot stress tests
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
  differences between Linux and U-Boot for stm32mp1 platform
2019-11-18 10:48:29 -05:00
Tom Rini
d64efd920e Merge tag 'u-boot-rockchip-20191118' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64
2019-11-17 21:15:57 -05:00
Michael Trimarchi
59b01eb7a1 rockchip: dts: tinker: Add tinker-s board support
Support tinker-s board. The board is equivalent of tinker board
except of emmc.

TODO:
- support of usb current burst when the board is powered from pc

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:51:25 +08:00
Michael Trimarchi
b40abe3369 rockchip: dts: tinker: Move u-boot dmc initialization to specific section
dmc is used to initialize the memory controller. It's needed by
u-boot. Move it in the specific section

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:51:25 +08:00
Thomas Hebb
64eff47c78 rockchip: imply instead of selecting SPL_SYS_MALLOC_SIMPLE
We shouldn't force which allocator the SPL uses, since there's no
platform requirement for one over the other: in fact, we currently allow
selection of the TPL allocator but not the SPL one!

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:51:25 +08:00
Thomas Hebb
857d638ca6 rockchip: allow DRAM init in SPL
The common SPL removed SoC-specific code for RK3399's SPL and in the
process caused the previously-unconditional DRAM initialization in
board_init_f() to only happen when compiling a configuration that does not
support TPL, meaning DRAM never gets initialized if TPL is supported but
disabled.

Fix this by omitting the DRAM init in SPL only when we are configured to
also build a TPL. This fixes custom configurations that have disabled
TPL, and it should also unbreak the "ficus-rk3399", "rock960-rk3399",
and "chromebook_bob" defconfigs, although since I don't have any of
those devices I can't confirm they're broken now.

Fixes: b7abef2ecb ("rockchip: rk3399: Migrate to use common spl board file")

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:54:29 +08:00
Thomas Hebb
220697a317 rockchip: SPL: fix ordering of DRAM init
The common SPL code reordered the DRAM initialization before
rockchip_stimer_init(), which as far as I can tell causes the RK3399 to
lock up completely.

Fix this issue in the common code by putting the DRAM init back after
timer init. I have only tested this on the RK3399, but it wouldn't make
any sense for the timer init to require DRAM be set up on any system.

Fixes: b7abef2ecb ("rockchip: rk3399: Migrate to use common spl board file")

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:51:25 +08:00
Andy Yan
208b8cd646 rockchip: rk3308: Add support for ROC-RK3308-CC board
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Andy Yan
9ce3de1b18 rockchip: rk3308: Add dts for ROC-RK3308-CC
Add dts file for ROC-RK3308-CC from firefly.

Sync form linux rockchip for v5.5-armsoc/dts64:
"arm64: dts: rockchip: Add devicetree for board roc-rk3308-cc"
(sha1: 4403e1237be3af0977aa23ef399e3496316317a0)

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Andy Yan
9e3de722e4 board: rockchip: Add rk3308 evb support
Add support for rk3308 evaluation board.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Andy Yan
22dcd28150 arm: dts: rockchip: Add dts for rk3308 evb
Add dts for rk3308 evb, sync from the linux kernel
upstream list [0].

[0]https://patchwork.kernel.org/patch/11201555/

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Andy Yan
f1a225229a arm: rockchip: Add RK3308 SOC support
RK3308 is a quad Cortex A35 based SOC with rich audio
interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which
designed for intelligent voice interaction and audio
input/output processing.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Elaine Zhang
bbda2ed584 rockchip: clk: pll: add common pll setting funcs
Common PLL setup function, compatible with different SOC.
Mainly for the subsequent new SOC use.

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
7acd030210 rockchip: rk3399: orangepi: Add init value for vdd_log
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
4d273ff304 rockchip: rk3399: khadas-edge: Add init value for vdd_log
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
8dda40ec51 rockchip: rk3399: rock-pi4: Add init value for vdd_log
We should set the init value when vdd_log is enabled, or else the
vdd_log output voltage may not in soc required range.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
f9f68ea747 arm64: dts: rk3399-rock960: add vdd_log and its init value
Add vdd_log node according to rock960 schematic V13.
This patch affect two boards:
- Rock960 Model A
- Ficus

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-11-17 17:22:53 +08:00
Peter Robinson
267b6adf63 rockchip: dts: rk3399-firefly: move u-boot, spl-boot-order to to the u-boot.dtsi
The u-boot specific device tree directives should be in u-boot.dtsi

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Peter Robinson
e7505d06bd rockchip: dts: rk3399-evb: move u-boot, spl-boot-order to to the u-boot.dtsi
The u-boot specific device tree directives should be in u-boot.dtsi

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Peter Robinson
f459e23ec0 rockchip: dts: rk3399: move the u-boot, dm-pre-reloc to the u-boot.dtsi
The u-boot specific pieces in the dts files should be in u-boot.dtsi
not the main files, this allows easier sync with upstream. The
rk3399.dtsi has a mix of both so move them all for consistency.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix with missing pmugrf)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Vasily Khoruzhick
de43ca7e3e rockchip: rk3399: split rockpro64 out of evb_rk3399
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Heiko Stuebner
a04f6fd17f rockchip: clk: rv1108: remove duplicate reset init
rockchip_reset_bind() already does the needed init for the reset
registers, only referenced the wrong cru structure.

So we can get rid of the open-coded reset init and just fix
the correct cru reference.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Soeren Moch
f210cbc1f3 arm: dts: rk3399-rockpro64: slightly increase center voltage
The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage
scaling. So the regulator reset voltage of 0.9V is used on this board.
Let u-boot initialize the center voltage to 0.95V as it is done for the
VD_LOGIC domain. This avoids instability and occasional linux kernel
Opses on this board.

Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Soeren Moch
5824ad3453 arm: dts: rk3399-rockpro64: sync dts from linux kernel
The most important change for u-boot is the fix for the vdd-log pwm
voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Jagan Teki
37f4e531d7 arm: dts: rk3399-roc-pc: Sync latest dts changes from Linux
Few important regulator power rails fixes are available in
linux-next, so sync them same.

Here is the last commit details:
commit <9f7f9b610e1b7d2dc86c543ab0dfcf781bd42326> ("arm64: dts:
rockchip: Fix roc-rk3399-pc regulator input rails")

Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
17224b325f rockchip: Init driver otg_data for rk3288 usb phy
RK3288 needs to init the otg_data in board level to make the phy driver
work.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
e76943ca6f rockchip: usb: Migrate to use ofnode
Migrate to use ofnode_* instead of fdt_* so that we may able to use live
dt for usb udc driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Heiko Stuebner
e9ccb2f526 rockchip: add px30 architecture core
Add core architecture code to support the px30 soc.
This includes a separate tpl board file due to very limited
sram size as well as a non-dm sdram driver, as this also has
to fit into the tiny sram.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:23:24 +08:00
Heiko Stuebner
537b1a2774 rockchip: add px30 devicetrees
Add px30 related devicetrees synced from the Linux kernel.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:23:20 +08:00
Heiko Stuebner
e61350a5f5 rockchip: misc: read cpuid either from efuse or otp
Newer Rockchip socs use a different ip block to handle one-time-
programmable memory, so depending on what got enabled get the cpuid
from either source.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:23:18 +08:00
Kever Yang
d49a526750 rockchip: clk: add px30 clock driver
The px30 contains 2 separate clock controllers, pmucru and cru.
Add drivers for them.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:23:07 +08:00
Heiko Stuebner
46281a76be rockchip: add core px30 headers
Add headers needed by the upcoming px30 support, including two
new dt-binding headers taken from the Linux kernel.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:23:00 +08:00
Heiko Stuebner
22b7b86005 spl: separate SPL_FRAMEWORK config for spl and tpl
Right now enabling SPL_FRAMEWORK will also enable it for the TPL in all
cases, making the TPL bigger. There may be cases where the TPL is really
size constrained due to its underlying ram size.

Therefore introduce a new TPL_FRAMEWORK option and make the relevant
conditionals check for both. The default is set to "y if SPL_FRAMEWORK"
to mimic the previous behaviour where the TPL would always get the
SPL framework if it was enabled in SPL.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Kever Yang
c8863b8508 ram: rk3399: update calculate_stride
Update the calculation of the stride to support all the DRAM case.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
YouMin Chen
a922d0d102 ram: rk3399: migrate to use common code
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
YouMin Chen
ca93e32139 ram: rk3328: use common sdram driver
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
YouMin Chen
39edfaa758 ram: px30: add sdram driver
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.

For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
Kever Yang
c525bb42aa ram: rockchip: add common msch reg definition
The noc register bit definition may be the same for different SoC while
the offset of the register may be different, add the struction
definition as common code.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
Kever Yang
691368c7f7 ram: rockchip: add phy driver code for PX30
This sdram_phy_px30.c is based on PX30 SoC, the functions are common
for phy, other SoCs with similar hardware could re-use it.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
Kever Yang
09d7872336 ram: rockchip: add controller code for PX30
This sdram_pctl_px30.c is based on PX30 SoC, the functions are common
for controller, other SoCs with similar hardware could re-use it.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
Kever Yang
d6647b08b2 ram: rockchip: add common code for sdram driver
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00