Commit graph

55 commits

Author SHA1 Message Date
Vladimir Zapolskiy
041c542219 phylib: remove a couple of redundant code lines
This change slightly improves readability of the phydev speed/duplex
assignment logic.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-09-10 00:08:26 +02:00
Vladimir Zapolskiy
e3a77218a2 phylib: reset mii bus only if reset handler is registered
This change allows to cope with a mii bus device registered using
miiphy_register(), which doesn't assign a default reset handler.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-09-10 00:07:55 +02:00
Wolfgang Denk
b91a9d9d4d phy.c: make less verbose - turn printf() into debug()
The PHY driver was too verbose and corrupted the boot message display
like this:

	...
	Net:   TSEC0 connected to Marvell 88E1111S
	TSEC1 connected to Marvell 88E1111S
	TSEC0, TSEC1
	...

Turn printf() into debug() so we het the expected output again:

	...
	Net:   TSEC0, TSEC1
	...

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
2011-08-31 22:35:27 +02:00
Andy Fleming
9082eeac5d phylib: Add a bunch of PHY drivers from tsec
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.

While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible).  Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:34 -05:00
Andy Fleming
5f184715ec Create PHY Lib for U-Boot
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:19 -05:00