For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.
This is a software Software Restrictions in i.MX53 reference manual:
29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout. It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.
Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.
Initialize b_max to 0 in all callers to mmc_register.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As Andy Fleming suggested, we can call mmc_init() in mmc_spi command.
So that we don't need to run mmcinfo command next.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts. All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1
are swapped.
Erratum SERDES-A001 says that if bank two is kept disabled and after bank
three is enabled, then the PLL for bank three won't lock properly. The
work-around is to enable and then disable bank two after bank three is
enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Part of the SERDES9 erratum work-around is to set some bits in the SerDes
TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The
current code does this only for XAUI, so extend it to the other protocols.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two
and three to be disabled (powered down) in the RCW. Display a warning
message if this is not the case.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the 'pixis_reset dump' command, which displays the contents of the PIXIS
registers. This command is only available if DEBUG is defined.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8641HPCN board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add function video_get_video_mode(), which parses the "video-mode" environment
variable and returns each of its components. The format matches the video=
command-line option used for Linux:
video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string>
<driver> The video driver, ignored by U-Boot
<xres> The X resolution (in pixels) to use.
<yres> The Y resolution (in pixels) to use.
<depth> The color depth (in bits) to use.
<freq> The frequency (in Hz) to use.
<options> A comma-separated list of device-specific options
Signed-off-by: Timur Tabi <timur@freescale.com>
There seems to be tools producing incorrect 'end of bitmap data'
markers '0100' in a RLE bitmap. Drawing such bitmaps can result
in overwriting memory above the frame buffer. E.g. on MPC5121e
based boards this memory can contain U-Boot environment.
We may not rely on the correct end of bitmap data marker 0001
only, but also have to check whether we are going to draw a
valid frame buffer scan line.
The patch provides a fix by maintaining a pixel counter
which is incremented by the amount of pixels we are going
to draw. If the counter exceeds frame buffer pixels limit
we stop the drawing with the error message.
Reported-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
The following boards gain device tree support with this patch:
ca9x4_ct_vxp - Versatile Express
i.mx5 boards:
efikamx
mx51evk
mx53evk
OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430
Tegra boards:
Harmony
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Deblock i2c bus when switching to another i2c bus, if using
i2c_set_bus_num().
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
To make sure that the mux can be configured a deblocking sequence
is done before the mux configuration. After the mux switch the new leaf
of, the i2c tree must be again deblocked.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
A lot of boards set FT_FSL_PCI_SETUP directly in their board code
and don't check to see if CONFIG_PCI is actually defined. This
will cause the board compilation to fail if CONFIG_PCI is not
defined. The p1022ds board is one such example.
Instead of fixing every board this patch wraps FT_FSL_PCI_SETUP
around CONFIG_PCI so we can remove CONFIG_PCI and boards will
still build properly.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
versioned SEC properties changed names during development, so
for now search and update LIODNs for both "secX.Y" and
"sec-vX.Y" based properties.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The workaround for ESDHC111 should also be applied on
P2040/P3041/P5010/P5020 SoCs.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rework and add some new APIs to the fsl_corenet_serdes code for use by
erratum and drivers.
* Rename serdes_get_bank() to serdes_get_bank_by_lane()
* Add serdes_get_first_lane returns which SERDES lane is used by device
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes a wrong address define in corenet_ds.h (used by
P4080DS.h, P3041DS.h, P5020DS.h).
Since board/Freescale/corenet_ds/tlb.c does not use the
CONFIG_SYS_PCIE3_MEM_VIRT define (uses CONFIG_SYS_PCIE1_MEM_VIRT with a
fix offset instead) this has no effect to the functionality. But it may
be important for changes in the future?
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix fdt bportal to pass the bman revision number to kernel via device tree.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make sure that machine change operation work successfully, change
timing parameters first before changing machine for chip select on IFC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we boot from a SD card use it for the environment as well.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot environments, esp. when boards are shared across multiple
users, can get pretty large and time consuming to visually parse.
The grepenv command this patch adds can be used in lieu of printenv
to facilitate searching. grepenv works like printenv but limits
its output only to environment strings (variable name and value
pairs) that match the user specified substring.
the following examples are on a board with a 5313 byte environment
that spans multiple screen pages:
Example 1: summarize ethernet configuration:
=> grepenv eth TSEC
etact=FM1@DTSEC2
eth=FM1@DTSEC4
ethact=FM1@DTSEC2
eth1addr=00:E0:0C:00:8b:01
eth2addr=00:E0:0C:00:8b:02
eth3addr=00:E0:0C:00:8b:03
eth4addr=00:E0:0C:00:8b:04
eth5addr=00:E0:0C:00:8b:05
eth6addr=00:E0:0C:00:8b:06
eth7addr=00:E0:0C:00:8b:07
eth8addr=00:E0:0C:00:8b:08
eth9addr=00:E0:0C:00:8b:09
ethaddr=00:E0:0C:00:8b:00
netdev=eth0
uprcw=setenv ethact $eth;setenv filename p4080ds/R_PPSXX_0xe/rcw_0xe_2sgmii_rev2_high.bin;setenv start 0xe8000000;protect off all;run upimage;protect on all
upuboot=setenv ethact $eth;setenv filename u-boot.bin;setenv start eff80000;protect off all;run upimage;protect on all
upucode=setenv ethact $eth;setenv filename fsl_fman_ucode_P4080_101_6.bin;setenv start 0xef000000;protect off all;run upimage;protect on all
usdboot=setenv ethact $eth;tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/initramfs.cpio.gz.uboot;tftp c00000 $dir/p4080ds-usdpaa.dtb;setenv bootargs root=/dev/ram rw console=ttyS0,115200 $othbootargs;bootm 1000000 2000000 c00000;
=>
Example 2: detect unused env vars:
=> grepenv etact
etact=FM1@DTSEC2
=>
Example 3: reveal hardcoded variables; e.g., for fdtaddr:
=> grepenv fdtaddr
fdtaddr=c00000
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
=> grep $fdtaddr
fdtaddr=c00000
my_boot=bootm 0x40000000 0x41000000 0x00c00000
my_dtb=tftp 0x00c00000 $prefix/p4080ds.dtb
nohvboot=tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/$ramdiskfile;tftp c00000 $dir/$fdtfile;setenv bootargs root=/dev/ram rw ramdisk_size=0x10000000 console=ttyS0,115200;bootm 1000000 2000000 c00000;
=>
This patch also enables the grepenv command by default on
corenet_ds based boards (and repositions the DHCP command
entry to keep the list sorted).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
commit 560d424b6d "env: re-add
support for auto-completion" fell short of its description -
the 'used' logic in hmatch_r was reversed - 'used' is 0 if
the hash table entry is not used, or -1 if deleted. This
patch makes hmatch_r actually match on valid ('used') entries,
instead of skipping them and failing to match anything.
typing 'printenv tft' and hitting 'tab' now displays valid
choices for variable names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: Mike Frysinger <vapier@gentoo.org>
If neither CONFIG_CMD_PING or CONFIG_CMD_SNTP are defined but
CONFIG_CMD_DNS is, a compile-time error will occur due to the
absence of a goto label.
Signed-off-by: Gray Remlin <gryrmln@gmail.com>
This patch fixes problems in the handling of redundant environment in env_sf.c
The major problem are double calls of free() on the allocated buffers,
which damages the internal data of malloc and crashes on next call.
In addition, the selection of the active environment had errors and compiler
warnings, which are corrected by this patch.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
If FB address is defined specific address then don't grab memory for LCD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
This patch defines all the needed symbols in the header file
and removes the now-unused config.mk in board directory.
Changes to board C file as requested.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
