On PH1-sLD3, eMMC and NAND are assigned to different I/O pins.
Both devices can be enabled at the same time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, these functions assume #address-cells and #size-cells are
both one. Fix them to support 64bit DTB.
Also, I am fixing a buffer overrun bug while I am here. The array
size of gd->bd->bd_dram is CONFIG_NR_DRAM_BANKS. The number of
iteration in the loop should be limited by that CONFIG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These defined were used for pre-DM ns16550 serial driver. They are
unneeded because UniPhier SoCs now use DM serial.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since no clock driver is implemented for peripherals in U-Boot yet,
this property is needed for the serial driver to set up the divisor
register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit prepares the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding new ones. Having flags would be better than
adding new members every time a new SoC-specific capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from our customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit d085ecd61b ("ARM: uniphier: switch to raw U-Boot image")
claimed that u-boot-with-spl.bin would be useful in its commit log,
but it was not available because the commit missed to define
CONFIG_SPL_MAX_SIZE. Without it, CONFIG_SPL_PAD_TO is not defined
either (see include/config_fallbacks.h). So, the SPL image is not
padded correctly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A83T has 3 PHYs, the last one being HSIC, which has 2 clocks.
Also there is only 1 OHCI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DLDO4 supplies power to the PD pins, and the AC200 Ethernet PHY /
composite video encoder.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The schematics of the h8_homlet_v2 show DCDC1 set to 3.3V. Some
Allwinner-based boards set it to 3.0V to conserve power. Since the
h8_homlet_v2 is a set-top box board with external power, there is
no such requirement.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY
on the A83T/H8.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3,
1.35V for DDR3L, and 1.2V for LPDDR3.
Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
AXP818 supports VBUS drive function, even though the manual does not
mention it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS drive is supported on AXP221 and later PMICs. Rework the macros
so we can support this on later PMICs without too much work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Like the Allwinner A33 SoC, the A83T is missing the config register
from the musb USB DRD hardware block. Use a known working value for
it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
axp818_init() is declared, but never defined.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
LDO3 and LDO4 are used to power port E resp. port G, which are exposed
on gpio headers, so enable them at 2.8V as specified in the schematic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Force master mode on the A20-OLinuXino-Lime2. This change is required
to get a reliable link at gigabit speeds.
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Force master mode for 1000BASE-T operation on the
A20-Olimex-SOM-EVB.
Karsten Merker reports that this change is necessary to get a reliable
link at gigabit speeds.
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.
This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.
There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.
CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com
Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This bit needs to be set for system suspend/resume to work. This setting
will be documented in an updated TRM at some time in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use a pointer to pass image address to fsl_secboot_validate(),
instead of using environmental variable "img_addr".
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case of fatal failure during secure boot execution (e.g. header
not found), reset is asserted to stop execution. If the RESET_REQ
is not tied to HRESET, this allows the execution to continue.
Add esbh_halt() after the reset to make sure execution stops.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For secure boot, currently we were using fixed bootargs for all SoCs.
This is not needed and we can use the bootargs which are used in
non-secure boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This commit solves CAAM coherency issue on ls2080. When caches are
enabled and CAAM's DMA's AXI transcations are not made cacheable,
Core reads/writes data from/to caches and CAAM does from main memory.
This forces data flushes to synchronize various data structures. But
even if any data in proximity of these structures is read by core,
these structures again are fetched in caches.
To avoid this problem, either all the data that CAAM accesses can be
made cache line aligned or CAAM transcations can be made cacheable.
So, this commit makes CAAM transcations as write back with write and
read allocate.
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When MMU is disabled, 64-bit write must be aligned at 64-bit
boundary. Becaue the memory location is not guaranteed to be 64-bit
aligned, the 64-bit write needs to be split into two 32-bit writes
to avoid the alignment exception.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs
to be put in bypass mode in uboot to enable CAAM transcations to pass
through.
For non-secure boot, SP BootROM doesn't enable SMMU, which is in
bypass mode out of reset.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The GUR (DCFG) registers in CCSR space are in little endian format.
Define a config CONFIG_SYS_FSL_CCSR_GUR_LE in
arch/arm/include/asm/arch-fsl-layerscape/config.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
