uclass_get_device_by_name() is meant to return 0 or a negative error code.
simple_itoa() cannot handle negative numbers.
This leads to output like:
=> bootdev list -p
Seq Probed Status Uclass Name
--- ------ ------ -------- ------------------
c [ ] 18446744073709551614 spi_flash spi.bin@0.bootdev
Convert the status to a positive number. Now we get
Seq Probed Status Uclass Name
--- ------ ------ -------- ------------------
c [ ] 2 spi_flash spi.bin@0.bootdev
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Enabling FIT_SIGNATURE required the old authentication method to be
disabled so disable this for K3 SOCs and enable FIT_SIGNATURE for K3
Platforms.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
[ cleanup the patch ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Change the device type from "usb_mass_storage" to "usb" when
booting a script.
Before this change:
=> printenv devtype
devtype=usb_mass_storage
After this change:
=> printenv devtype
devtype=usb
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some devices keep 2 copies of the bootloader_message in the misc
partition and write each in sequence when updating. This ensures that
there is always one valid copy of the bootloader_message. Teach u-boot
to optionally try a backup bootloader_message from a specified offset if
the primary one fails its CRC check.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
It is is sometimes desired to be able to skip decrementing the number of
tries remaining in an Android A/B boot, and instead just check which
slot will be tried later. This can commonly be be the case for platforms
that want to A/B u-boot itself, but are required to boot from a FAT MBR
partition. In these cases, u-boot must do an early check that the MBR
points to the correct A/B boot partition, and if not rewrite the MBR to
point to the correct one and reboot. Decrementing the try count in this
case is not desired because it means that each u-boot might constantly
ping-pong overwriting the MBR and rebooting until all the retries are
used up.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
It is possible to boot x86-based ChromeOS machines by parsing a table and
locating the kernel and command line. Add a bootmeth for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some Linux parameters can be set automatically by U-Boot, if it knows the
device being used. For example, since U-Boot knows the serial console
being used, it can add parameters for earlycon and console.
Add support for this.
Note that this is an experimental feature and we will see how useful it
turns out to be. It is very handy for ChromeOS, since otherwise it is very
difficult to manually determine the UART address or port number,
particularly in a script.
Provide an example of how this is used with ChromeOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a bootflow command to update the command line more easily. This allows
changing a particular parameter rather than editing a very long strings.
It is also easier to handle with scripting.
The new 'bootflow cmdline' command allows getting and setting single
parameters.
Fix up the example output while we are here, since there are a few new
items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Linux command line consists of a number of words with optional values.
At present U-Boot allows this to be changed using the bootargs environment
variable.
But this is quite painful, since the command line can be very long.
Add a function which can adjust a single field in the command line, so
that it is easier to make changes before booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The "bootargs" environment variable is used to set the command-line
arguments to pass to the OS. Use this same mechanism with bootstd as well.
When the variable is updated, it is written to the current bootflow. When
the current bootflow is updated, the environment variable is updated too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It seems better to call this a 'bootdev' since this is name used in the
documentation. The older 'Bootdevice' name is no-longer used and may cause
confusion with the 'bootdevice' environment variable.
Update throughout to use bootdev.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new 'cedit' command which allows editing configuration using an
expo. The configuration items appear as menus on the display.
This is extremely basic, only supporting menus and not providing any way
to load or save the configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The only way to create an expo at present is by calling the functions to
create each object. It is useful to have more data-driven approach, where
the objects can be specified in a suitable file format and created from
that. This makes testing easier as well.
Add support for describing an expo in a devicetree node. This allows more
complex tests to be set up, as well as providing an easier format for
users. It also provides a better basis for the upcoming configuration
editor.
Signed-off-by: Simon Glass <sjg@chromium.org>
It looks better if menus have a bit of an inset, rather than be drawn hard
up against the background. Also, menu items look better if they have a bit
of spacing between them.
Add theme options for these and implement the required changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
In 'popup' mode, the expo allows moving around the objects in a scene.
When 'enter' is pressed on a menu, it opens and the user can move around
the items in the menu.
Implement this using keypress handles and actions.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a menu is opened, it must be displayed over all other objects in
the scene, so that all its items are visible.
Handle this by drawing the menu object a second time, after all other
objects have been drawn. Draw all of the objects which are dependent
on the menu object.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a popup menu is closed it shows only the selected item. When it is
open it shows a background and all items, with a highlight that can be
moved between the items.
Add the drawing logic for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we only support a single menu, so all that can be pointed to
is the current menu item. Rename this action so that we can also add
an action for pointing to an object. This will allow cycling through
the objects in a scene.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only a single menu is supported. All items are shown and a
pointer object points to the current item.
Add support for multiple menus, one of which is highlighted, indicated
by the highlight_id property in the scene.
The highlighted menu item has a SCENEOF_POINT flag, indicating that it
is currently pointed to.
The popup menu is normally closed, in which case it shows only the
current menu item. When it is opened, it shows all items, allowing the
user to select one.
Rather than requiring the menu item to have a description, require it to
have a label. Use the label (only) for the popup menu.
With this, most of the drawing and layout logic is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current implementation supports a 'pointer' object which points to
the currently highlighted menu item. We want to support highlighting the
label of the menu item instead, e.g. with inverse video. In this case we
will need to 'unhighlight' the old item and highlight the new one.
As a first step, move the pointer logic into a function. This fixes a
bug where the item is hidden when it should not be.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to manually set the fonts of all objects to be consistent.
Some spacing settings are also better set globally than by manually
positioning each object.
Add a 'theme' to the expo, to hold this information. For now it includes
only the font size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to set the full dimensions of objects, i.e. including the
width and height.
For menus, calculate the bounding box of all objects in the menu. Set all
labels to be the same size, so that highlighting works correct, once
implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than estimating, measure the text accurately, using the new
vidconsole feature. This allows accurate placement of objects.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currently have just a 'hide' property for each object. In preparation
for adding more properties, convert the struct to use a flags value,
instead of individual booleans. This is more extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present objects only have a position so it is not possible to determine
the amount of space they take up on the display.
Add width and height properties, using a struct to keep all the dimensions
together.
For now this is not used. Future work will set up these new properties.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to set this value so that it is easy to separate the
statically allocated IDs (generated by the caller) from those
generated dynamically by expo itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is different enough from bootstd that it probably deserves
its own log category. It cannot use a uclass since it is not a device.
Add a new category.
Signed-off-by: Simon Glass <sjg@chromium.org>
This functionality current sits in bootstd, but it is more generally
useful. Add a function to load a file into memory, allocating it as
needed. Adjust bootstd to use this version.
Note: Tests are added in the subsequent patch which converts the 'cat'
command to use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This should ideally be done once after all scene changes have been made.
Require an explicit call when everything is ready.
Always arrange after a key it sent, just for convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is easier to deal with if it uses the existing string handling,
since we will be able to use translations, etc. in the future.
Update it to use an ID instead of a string.
Signed-off-by: Simon Glass <sjg@chromium.org>
On the arm64 architecture booti_setup() is called for EFI FIT images.
This function call fails because EFI images typically do not have a
kernel signature.
Check that the operating system property "os" of the image is "linux"
before invoking booti_setup().
Fixes: 487b5fa6de ("bootm: Handle kernel_noload on arm64")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using relative path in a /boot/extlinux/extlinux.conf file fails to load
linux kernel.
Using a /boot/extlinux/extlinux.conf file:
LABEL test
LINUX ../linux/Image
Result in following error:
Retrieving file: ../linux/Image
Skipping test for failure retrieving kernel
Boot failed (err=-14)
However, using sysboot cmd successfully load kernel using same file:
sysboot mmc 1:1 any ${scriptaddr} /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/../linux/Image
Fix relative path using bootmeth extlinux by supplying bootfile path
instead of subdir path in the call to pxe_setup_ctx, same as done in the
sysboot command.
Fixes: 31aefaf89a ("bootstd: Add an implementation of distro boot")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move BOOTSTD_FULL down in the file so that it can be enabled only when
BOOTSTD is enabled. This prevents a build error if BOOTSTD is disabled
but BOOTSTD_FULL is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We cannot be sure what bootmeth a distro will need to use. Add a new
BOOTMETH_DISTRO option which collects these together. Select this from
BOOTSTD_DEFAULTS so that it is clear what is needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make BOOTMETH_EFILOADER depend on EFI_LOADER, select if EFI_LOADER]
Signed-off-by: Tom Rini <trini@konsulko.com>
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a few cases the error handling is not quite right. Make sure we
return the actual error in distro_efi_read_bootflow_file() rather than
-EINVAL. Return -IO when a file cannot be read. Also show the error name
if available.
This does not change operation, but does make it easier to diagnose
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch to relax flag requirements was not accepted[1], so we still have
to have separate bootcommands depending on CMD_BOOTFLOW_FULL.
The previous attempt at this did not work, since it used the wrong name
for the options.
Fix this and change the message to mention BOOTSTD_FULL since this affects
not just the flags, but all functionality, so is more likely what the user
wants.
Drop the useless condition on CMD_BOOTFLOW_FULL while we are here.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20230329071655.1959513-2-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a91492b6e9 ("bootstd: Provide a default command")
Armbian uses a script which needs the HUSH parser. It is likely that
other distros will do the same. Enable it by default, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
If there is no partition numbered 1, we decide that there are no
partitions at all. That may not be correct, since at least one Debian
installed has just a single partition numbered 2.
Continue searching up to partition 3, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Renesas RZ/N1 devices contain BootROM code that loads a custom SPKG
image from QSPI, NAND or USB DFU. Support this format in mkimage tool.
SPKGs can optionally be signed, however creation of signed SPKG is not
currently supported.
Example of how to use it:
tools/mkimage -n board/schneider/rzn1-snarc/spkgimage.cfg \
-T spkgimage -a 0x20040000 -e 0x20040000 \
-d u-boot.bin u-boot.bin.spkg
The config file (spkgimage.cfg in this example) contains additional
parameters such as NAND ECC settings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Adds commands to support DHCP and PXE with IPv6.
New configs added:
- CMD_DHCP6
- DHCP6_PXE_CLIENTARCH
- DHCP6_PXE_DHCP_OPTION
- DHCP6_ENTERPRISE_ID
New commands added (when IPv6 is enabled):
- dhcp6
- pxe get -ipv6
- pxe boot -ipv6
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Fix comments syntax error in SPL_LOAD_FIT_APPLY_OVERLAY description.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
vbe_simple_read_bootflow() calls vbe_simple_read_bootflow_fw()
which is only available when BOOTMETH_VBE_SIMPLE_FW is on.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When loading a file from a block device, efiload_read_file
was using the seq_num of the device (e.g "35" of virtio_blk#35)
instead of the block device id (e.g what you get from running
the corresponding device scan command, like "virtio 0")
This cause EFI booting from these devices to fail as an
invalid device number is passed to blk_get_device_part_str:
Scanning bootdev 'virtio-blk#35.bootdev':
distro_efi_read_bootflow_file start (efi,fname=<NULL>)
distro_efi_read_bootflow_file start (efi,fname=<NULL>)
setting bootdev virtio, 35, efi/boot/bootaa64.efi, 00000000beef9a40, 170800
efi_dp_from_name calling blk_get_device_part_str
dev=virtio devnr=35 path=efi/boot/bootaa64.efi
blk_get_device_part_str (virtio,35)
blk_get_device_by_str (virtio, 35)
** Bad device specification virtio 35 **
Using default device tree: dtb/qemu-arm.dtb
No device tree available
0 efi ready virtio 1 virtio-blk#35.bootdev.par efi/boot/bootaa64.efi
** Booting bootflow 'virtio-blk#35.bootdev.part_1' with efi
blk_get_device_part_str (virtio,0:1)
blk_get_device_by_str (virtio, 0)
No UEFI binary known at beef9a40 (image buf=00000000beef9a40,addr=0000000000000000)
Boot failed (err=-22)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when debugging is off, bootdev_find_in_blk() sometimes fails
to find a valid bootflow, e.g. with virtio. Accessing the 'blk' variable
later in the function seems to correct it.
Move the 'ret' check before the debug statement and set the block device
again aftewards, to work around this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the -l flag to indicate whether to report missing uclasses.
Also try to be more helpful when no devices are found. For example, when
we see something 'scsi0' requested and nothing was found, this indicates
that there are no SCSI devices, so show a suitable message.
Move messages out of the low-level functions so that silent operation
is possible.
This means they are never reported unless BOOTSTD_FULL is enabled, since
the -l flag cannot otherwise be set.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current EFI implementation has a strange quirk where it watches
loaded files and uses the last-loaded file to determine the device that
is being booted from.
This is confusing with bootstd, where multiple options may exist. Even
loading a device tree will cause it to go wrong. There is no API for
passing this information, since the only entry into booting an EFI image
is the 'bootefi' command.
To work around this, call efi_set_bootdev() for EFI images, if possible,
just before booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should only store the FDT filename if we were able to determine one.
Adjust the logic for this.
This corrects the case where no FDT is needed to boot, such as with EFI
using ACPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building with clang we get a warning that rdaddr could be
uninitialized in one case. While this cannot functionally happen, we can
easily silence the warning.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the script loading code to recognize when script data is stored
externally from the FIT metadata (i.e., built with `mkimage -E`).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the support for boot image header version 3 and 4
using abootimg command.
In order to use version 3 or 4:
1- Vendor boot image address should be given to abootimg cmd.
abootimg addr $1 $vendor_boot_load_addr
2- "ramdisk_addr_r" env variable (ramdisk address) should be set to host
the ramdisk : generic ramdisk + vendor ramdisk
Replace "struct andr_boot_img_hdr_v0*" by "void *" in
some functions since v3 and v4 are now supported as well.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Add support for boot image version 3 and 4 in
android_image_get_dtb_img_addr().
Since the dtb is now included in vendor_boot image
instead of boot image, extract the dtb address from
vendor_boot image when a v3 or v4 is used.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
In version 3 and 4 of boot image header, the vendor specific
command line are located in vendor boot image. Thus, use
extra command line to add those cmd to bootargs.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Version 3 and 4 of boot image header introduced
vendor boot ramdisk: Please check include/android_image.h
for details.
The ramdisk is now split into a generic ramdisk in boot image
and a vendor ramdisk in vendor boot image.
Support the new vendor ramdisk.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Since boot image header version 3 and 4 introduced vendor boot image,
use the following functions to fill the generic android
structure : andr_image_data:
- android_boot_image_v3_v4_parse_hdr()
- android_vendor_boot_image_v3_v4_parse_hdr()
Update android_image_get_data() to support v3 and v4
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce vendor boot image for version 3 and 4 of boot image header.
The vendor boot image will hold extra information about kernel, dtb
and ramdisk.
This is done to prepare for boot image version 3 and 4 support.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
android_image_get_dtbo() is used to get recovery DTBO via abootimg cmd.
This is not supported in boot image header v3 and v4. Thus, print an
error message when v1,v2 header version are not used.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Content print is not supported for version 3 and 4 of boot image header.
Thus, only print that content when v2 is used.
Update android_print_contents() to print an error message
when trying to print boot image header version 3 or 4 content.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Move from andr_boot_img_hdr_v0 to andr_image_data
structure to prepare for boot image header
version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
andr_image_data structure is used as a global representation of
boot image header structure. Introduce this new structure to
support all boot header versions : v0,v1.v2.v3.v4 and to support
v3 and v4 while maitaining support for v0,v1,v2.
The need of using andr_image_data comes from the change of header
structure in both version 3 and 4.
Rework android_image_get_kcomp() to support this new struct.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the new vendor boot image introduced in versions 3 and 4
of boot image header, the header check must be done for both boot
image and vendor boot image. Thus, replace android_image_check_header()
by is_android_boot_image_header() to only refer to boot image header check.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Android introduced boot header version 3 or 4.
The header structure change with version 3 and 4 to support
the new updates such as:
- Introducing Vendor boot image: with a vendor ramdisk
- Bootconfig feature (v4)
Change andr_img_hdr struct name to maintain support for version v0,
v1 and v2 while introducing version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
In case fitImage support is disabled, and image_locate_script() is
passed a fitImage, then the 'data' variable is used uninitialized.
Drop into the default: branch of the switch-case statement and do
not return the uninitialized data, and do not modify the return
pointer either, just print an error message.
Reported by clang build:
"
$ make HOSTCC=clang CC=clang KCFLAGS=-Werror sandbox64_defconfig && make HOSTCC=clang CC=clang KCFLAGS=-Werror
...
boot/image-board.c:1006:7: error: variable 'data' is used uninitialized whenever switch case is taken [-Werror,-Wsometimes-uninitialized]
case IMAGE_FORMAT_LEGACY:
^~~~~~~~~~~~~~~~~~~
include/image.h:608:29: note: expanded from macro 'IMAGE_FORMAT_LEGACY'
^~~~
boot/image-board.c:1128:19: note: uninitialized use occurs here
*datap = (char *)data;
^~~~
boot/image-board.c:1001:11: note: initialize the variable 'data' to silence this warning
u32 *data;
^
= NULL
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These two features use a lot of common options. Move them into a common
CONFIG to reduce duplication.
Use 'select' for most options since these are things that boards aren't
supposed to override. For now it is not possible to disable
BOOT_DEFAULTS but we may take another look later.
Note that five options use 'imply' to match existing behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Rework a bit so we don't grow so many platforms unintentionally]
Signed-off-by: Tom Rini <trini@konsulko.com>
For EFI, the distro boot scripts search in three different directories
for the .dtb file. The SOC-based filename fallback is supported only for
32-bit ARM.
Adjust the code to mirror this behaviour.
Also some boards can use a prior-stage FDT if one is not found in the
normal way. Support this and show a message in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Mark Kettenis <kettenis@openbsd.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_DM_RNG defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_CMD_BOOTEFI_BOOTMGR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_PSTORE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_FDT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_BOOTM_PRE_LOAD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_BOOTI defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This supports reading a kernel and ramdisk from qfw, then loading it with
either the booti or bootz commands.
For now this uses the existing booti and bootz commands, rather than
trying to call that functionality directly (e.g. do_bootm_states()). It
does not require the HUSH parser though, which helps a little with size.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases the block device is obtained but is not probed, since it
is a sibling of the bootdev. Make sure it is probed, so it can be used
without any trouble.
This fixes a bug with virtio, where the device is accessed before it has
been set up by the virtio uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 201417d700 ("bootstd: Add the bootdev uclass")
Reported-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is sometimes useful to have one without the other, e.g. on a device
without a display, since at present the expo feature requires CONFIG_VIDEO
to be enabled.
Update the Makefile and bootflow command to support this, as well as the
EXPO dependency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to record the bootdevs used when scanning for bootflows. This is
useful for testing.
Enable this only with BOOTSTD_FULL and do the same for the progress
reporting.
Re-enable and update the affected tests now that we have this feature.
For bootdev_test_order_default() there is no-longer any support for using
the bootdev aliases to specify an ordering, so drop that part of the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not used outside tests. Drop it and rename
bootflow_scan_dev() since it is how we start a scan now.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to support scanning a single label, like 'mmc' or 'usb0'. Add
this feature by plumbing the label through to the iterator, setting a
flag to indicate that only siblings of the initial device should be used.
This means that scanning a bootdev by its name is not supported anymore.
That feature doesn't seem very useful in practice, so it is no great loss.
Add a test for bootdev_find_by_any() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we set up the bootdev order at the start, then scan the
bootdevs one by one.
However this approach cannot be used with hunters, since the bootdevs may
not exist until the hunter is used. Nor can we just run all the hunters at
the start, since that violate's U-Boot's 'lazy init' requirement. It also
increases boot time.
So we need to adjust the algorithm to scan by labels instead. As a first
step, drop the dev_order[] array in favour of a list of labels. Update the
name of bootdev_setup_iter_order() to better reflect what it does.
Update some related comments and log messages. Also disable a few tests
until a later commit where we can use them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which moves to the next priority to be processed.
This works by storing the current priority in the bootflow iterator. The
logic to set this up is included in a subsequent commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which moves to the next label in a list of labels. This
allows processing the boot_targets environment variable.
This works using a new label list in the bootflow iterator. The logic to
set this up is included in a subsequent commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to hunt for a bootdev label and find the bootdev produced
by the hunter (or already present).
Add a few extra flags so that we can distinguish between "mmc1", "mmc" and
"1" which all need to be handled differently.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are associated with the ethernet boot device but do not match its
uclass name, so handle them as special cases.
Provide a way to pass flags through with the bootdev so that we know
how to process it. The flags are checked by the bootmeths, to ensure that
only the selected bootmeth is used.
While these both use the network device, they work quite differently. It
is common to run only one of these, or to run PXE before DHCP. Provide
bootflow flags to control which methods are used. Check these in the two
bootmeths so that only the chosen one is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this bootmeth only supports a block device and the sandbox
host filesystem. Add support for obtaining the script from a network
device. Also implement the set_bootflow() method so that it is easy
for other bootdevs (such as enabling SPI flash to support scripts).
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev for SPI flash so that these devices can be used with
standard boot. It only supports loading a script.
Add a special case for the label, since we want to use "spi", not
"spi_flash".
Enable the new bootdev on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Normally the bootmeth driver reads the bootflow from the bootdev, since
it knows the correct way to do it.
However it is easier for some bootdevs to handle this themselves. For
example, reading from SPI flash is quite different from other devices.
Add a way for the bootdev to pass a bootflow to the bootmeth, so that
this can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is complicated enough to merit its own function, particularly as we
are about to add to it. Create a new label_to_uclass() function to decode
a label.
Also update the code to ignore an empty label or one consisting of just a
number.
Signed-off-by: Simon Glass <sjg@chromium.org>
This environment variable is supposed to be set so that the script knows
which partition holds the script. Set it before invoking the script.
Signed-off-by: Simon Glass <sjg@chromium.org>
With EFI booting the device tree is required but is not actually specified
in any way. The normal method is to use a fdtfile environment variable to
get the filename, then look for that file on the media.
Implement this in the bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths provide a way to load a device tree as well as the base
OS image. Add a way to store this in the bootflow. Update the
'bootflow info' command to show this information.
Note that the device tree is not allocated, but instead is stored at
an address provided by an environment variable. This may need to be
adjusted at some point, but for now it works well and fits in with the
existing distro-boot scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this bootmeth only supports reading from a filesystem. Add
support for reading from a network also, using DHCP with autoload.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all partitions are scanned, whether marked bootable or not.
Use only bootable partitions, defaulting to partition 1 if none is
found.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to run a bootdev hunter to find bootdevs of a certain type. Add
this to the 'bootdev hunt' command. Test for this are added in a later
patch, since a useful test needs some hunters to work with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootdevs must be enumerated before they appear. For example, USB
bootdevs are not visible until USB is enumerated.
With standard boot this needs to happen automatically, since we only
want to enumerate a bus if it is needed.
Add a way to define bootdev 'hunters' which can be used to hunt for
bootdevs of a given type. Track which ones have been used and add a
command to list them.
Include a clang work-around which seems to be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code in these functions turns out to often be the same. Add a default
get_bootflow() function and allow the drivers to select it by setting
the method to NULL.
This saves a little code space.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present MMC uses the bootdev_setup_for_dev() function to set up the
bootdev. This is because MMC only has one block-device child, so does not
need to worry about naming of the bootdev.
However this inconsistency with other bootdevs that use block devices is a
bit annoying. The only real reason for it is to have a name like
'mmc0.bootdev' instead of 'mmc0.blk.bootdev'.
Update bootdev_setup_sibling_blk() to drop '.blk' from the name where it
appears, thus removing the only reason to use the bootdev_setup_for_dev().
Switch MMC over to the subling function.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no point in trying to match the alias order for bootdevs, since
build_order() either sorts them by priority, uses the boot_targets
environment variable or the bootdev-order property.
Just use the iterator instead, to simplify the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than implement this as its own case in build_order(), process the
boot_targets environment variable in the bootstd_get_bootdev_order()
function. This allows build_order() to be simplified.
Signed-off-by: Simon Glass <sjg@chromium.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
This device is created when there are no bootmeths defined in the device
tree. But it cannot be probed without a device tree node.
For now, ignore a probe failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Karsten Merker <merker@debian.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: a56f663f07 ("vbe: Add info about the VBE device to the fwupd node")
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Karsten Merker <merker@debian.org>
Instead of the bash script, use binman to generate the FIT for arm64.
For 32-bit boards, use binman for all images, dropping the intermediate
files.
With this change, only Zynq is now using SPL_FIT_GENERATOR so update the
Kconfig rule accordingly.
Clean up the Makefile to the extent possible. Unfortunately, two boards
do not use SPL_FRAMEWORK so don't enable the u-boot.img rule:
evb-rk3036
kylin-rk3036
So a small remnant remains.
Signed-off-by: Simon Glass <sjg@chromium.org>
The event framework is just that, a framework. Enabling it by itself
does nothing, so we shouldn't ask the user about it. Reword (and correct
typos) around this the option and help text. This also applies to
DM_EVENT and EVENT_DYNAMIC. Only EVENT_DEBUG and CMD_EVENT should be
visible to the user to select, when EVENT is selected.
With this, it's time to address the larger problems. When functionality
uses events, typically via EVENT_SPY, the appropriate framework then
must be select'd and NOT imply'd. As the functionality will cease to
work (and so, platforms will fail to boot) this is non-optional and
where select is appropriate. Audit the current users of EVENT_SPY to
have a more fine-grained approach to select'ing the framework where
used. Also ensure the current users of event_register and also select
EVENT_DYNAMIC.
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Oliver Graute <Oliver.Graute@kococonnector.com>
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Fixes: 42fdcebf85 ("event: Convert misc_init_f() to use events")
Fixes: c5ef202557 ("dm: fix DM_EVENT dependencies")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Create an expo to handle the boot menu. For now this is quite simple, with
just a header, some menu items and a pointer to show the current one.
Signed-off-by: Simon Glass <sjg@chromium.org>
A menu is a key part of the expo design. It consists of a number of items
which the user can select from.
Add the initial implementation of this.
Signed-off-by: Simon Glass <sjg@chromium.org>
A scene is a single screen within an expo. It is possible to move between
scenes but only one can be displayed at once.
Add a basic implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
An expo is a way of presenting and collecting information from the
user. It consists of a collection of 'scenes' of which only one is
presented at a time. An expo is typically used to show a boot menu
and allow settings to be changed.
One created, the same expo can be automatically presented in graphical
form using a vidconsole, or in text form on a serial console.
Add an initial implementation of the expo itself. Supports for scenes
and objects is provided later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some operating systems provide a logo in bmp format. Read this in if
present so it can be displayed in the menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the concept of an OS name to the bootflow. This typically includes the
OS name, version and kernel version.
Implement this for the distro and script bootmeths so that it works with
Armbian and older version of Fedora.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit d5ba6188df ("cmd: pxe_utils: Check fdtcontroladdr in label_boot")
forces '$fdtcontroladdr' DT address as a third parameter of bootm command
even if the PXE transfer pulls in a fitImage which contains configuration
node with its own DT that is preferrable to be passed to Linux. Limit the
$fdtcontroladdr fallback utilization to non-fitImages, since it is highly
likely a fitImage would come with its own DT, while single-file images do
need a separate DT.
Fixes: d5ba6188df ("cmd: pxe_utils: Check fdtcontroladdr in label_boot")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Hoyes <peter.hoyes@arm.com>
Tested-by: Peter Hoyes <peter.hoyes@arm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
This reverts commit ed6251187a.
Superseded by "cmd: pxe_utils: Limit fdtcontroladdr usage to non-fitImage"
which is less heavy-handed approach and retains part of the original
behavior for non-fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When converting CONFIG_SDCARD and CONFIG_SPIFLASH to Kconfig, one set of
uses wasn't converted correctly. Allow for the case where platforms
don't rely on "PBL" to boot but instead use other mechanisms. See the
link below for more details.
Link: https://lore.kernel.org/all/20220802091338.f4g45ldhc7qbg6hm@pali/
Fixes: d433c74eec ("Convert CONFIG_SDCARD et al to Kconfig")
Tested-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We ask for CONFIG_SPL_LOAD_FIT_ADDRESS in Kconfig, so we cannot define
it in C as a fall-back. However, this option previously was buried under
"if ... endif" Kconfig logic. Rework a number of config options to now
have more robust dependency lines so that we can ask this address when
needed. With that done, we can remove the fallback in spl_ram.c.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the change here, all extlinux.conf files with only "KERNEL
/fitImage" don't work anymore. One common example of this would be those
files generated by thee Poky/OE WIC bootimg-partition bootloader
partition generator.
This reverts commit d5ba6188df.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Reported-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Regarding the documentation found here:
https://github.com/u-boot/u-boot/blob/master/common/menu.c#L347
If both timeout and prompt is set to 0 the default entry shall
be booted immediately. However the current behaviour is that
the prompt is shown (tested with distroboot) until the user
selects an entry (no timeout).
This change implements a behaviour as documented. It was tested
with distroboot.
Signed-off-by: Manuel Traut <manuel.traut@mt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace malloc and strcpy by strdup in
function parse_label_kernel.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Since the commit d5ba6188df ("cmd: pxe_utils: Check fdtcontroladdr
in label_boot") the FDT or the FDTDIR label is required in extlinux.conf
and the fallback done by bootm command when only the device tree present
in this command parameters is no more performed when FIT is used for
kernel.
When the label FDT or FDTDIR are absent or if the device tree file is
absent, the PXE command in U-Boot uses the default U-Boot device tree
selected by fdtcontroladdr = gd->fdt_blob, it is the "Scenario 3".
With this scenario the bootm FIP fallback is no more possible with
the extlinux.conf when only "kernel" label is present and is a FIP:
kernel <path>#<conf>[#<extra-conf[#...]]
As the U-Boot FDT is always provided in the third bootm argument,
the device tree found in FIP is not used as fallback, it was done
previously in boot_get_fdt().
This patch adds a new field kernel_label to save the full kernel label.
The FDT bootm parameters use the kernel address (to avoid to load a
second time the same FIP) and the config when this full label is reused
for "fdt" or "initrd" label.
This FIP support in extlinux.conf is restored when the "FDT" label
can be found and select the same FIP (identical file and configuration):
kernel <path>#<conf>[#<extra-conf[#...]]
fdt <path>#<conf>[#<extra-conf[#...]]
The patch add also this possibility for initrd.
initrd <path>#<conf>[#<extra-conf[#...]]
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reorder kernel treatment in label_boot at the beginning of the function.
This patch doesn't change the pxe command behavior, it is only a
preliminary step for next patch, build kernel_addr before parsing
the label initrd and fdt to build the next bootm arguments.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
If the user select the image type "flat_dt" a FIT image will be build.
This breaks the legacy use case of putting a Flat Device Tree into a
legacy u-boot image.
Add a new image type "fdt_legacy" to build a legacy u-boot image
with a "flat_dt" type.
Link: https://lore.kernel.org/all/20221028155205.ojw6tcso2fofgnhm@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
As there are no more non-DM_ETH cases for networking, remove this legacy
file and update the Makefile to match current usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to usage of PREBOOT in Kconfig, macro CONFIG_PREBOOT is always defined
when CONFIG_USE_PREBOOT is enabled. In case CONFIG_PREBOOT is not
explicitly enabled it is set to empty C string and therefore
'#ifdef CONFIG_PREBOOT' guard does not work. Fix this issue by introducing
a new Kconfig symbol PREBOOT_DEFINED which cause to define new C macro
CONFIG_PREBOOT_DEFINED only when CONFIG_PREBOOT is really defined.
Change usage of '#ifdef CONFIG_PREBOOT' by '#ifdef CONFIG_USE_PREBOOT' for
code which checks if preboot code would be called and by
'#ifdef CONFIG_PREBOOT_DEFINED' for defining preboot code.
Signed-off-by: Pali Rohár <pali@kernel.org>
