Update QIXIS related code to be executed only if CONFIG_FSL_QIXIS
flag is enabled. In case QIXIS code is not enabled, use default
sysclk value as 100MHz per board documentation.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_ESBC_VALIDATE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reset ENET_RST_B to make ENET function stable.
Since DM_GPIO enabled, we use "gpio_spi@0_5" which corresponds
to ENET_RST_B.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Now that mx6sabresd_spl_defconfig can be used to boot all
mx6sabresd variants, the non-SPL targets can be safely removed.
Signed-off-by: Fabio Estevam <fabio.estvam@nxp.com>
Add support for the mx6dlsabresd board in SPL.
Retrieved the DCD table from:
board/freescale/mx6sabresd/mx6dlsabresd.cfg
(NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga)
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabresd boards.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently only MX6Q/QP sabresd boards are supported in SPL.
In order to also support MX6DL we need to convert to using
IOMUX_PADS and SETUP_IOMUX_PADS macros.
Other than that move the <asm/arch/mx6-ddr.h> header inclusion to the
SPL code block in order to avoid build error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function 'spin_wheel' is declared as inline, but not static and thus
we see warnings that 'w' and 'p' are declared static in a non-static
inline function. Correct this by marking spin_wheel as static inline.
Cc: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable usdhc1_pads is only referenced during SPL builds, add a guard.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The variable usdhc1_pads is only referenced during SPL builds, add a
guard.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
With gcc-6 we see a warning that sysclk_tbl is defined but unused, so
remove it.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 088454cd dropped return value from initram(), setting
gd->ram_size directly. Three boards were missed for SPL boot.
Signed-off-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since commit ce412b7, RGMII TX clock internal delay is not enabled
for AR8033 unconditionally. On LS1021ATWR board, the third port
eTSEC3 uses AR8033 in RGMII mode. The TX/RX internal delay needs to
be enabled.
This patch will set PHY_INTERFACE_MODE_RGMII_ID to enable RGMII TX/RX
clock internal delay for AR8033 on the third port.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As board-specific reset logic, it needs to issue reset signal
via CPLD when issuing 'reset' command in u-boot, this patch
solves the issue of reset command not working on T1024RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
Explain how to flash the eMMC and how to boot from it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves sec_init to board_init rather than in misc_init function beacuse
PPA will be initialised in board_init function and for PPA validation
sec_init has to be done prior to PPA init.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. So needs to enable them together.
DM FEC and SPI are not enabled, but they use gpio in board code.
So use gpio_request first to request the gpio, because DM_GPIO
is enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different
Add new function adjust_vdd() for LSCH3 compliant SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
In some cases this is absolutely required, so select this for some secure
features. This also requires migration of RSA_FREESCALE_EXP
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PPA implements PSCI which requires for power managment.
Added support of PPA for LS1012AQDS, LS1012ARDB and LS1012AFRDM.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PPA binary needs to be relocated on secure DDR, hence marking out
a portion of DDR as secure if CONFIG_SYS_MEM_RESERVE_SECURE flag
is set
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set cpo_sample as suggested by the driver
"WARN: pls set popts->cpo_sample = 0x58 in <board>/ddr.c to optimize
cpo".
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Introduce board/freescale/common/Kconfig so that we have a single place
for CONFIG options that are shared between ARM and PowerPC NXP platforms.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On LS1012ARDB board, three dual 1:4 mux/demux devices drive the SDHC2
signals to eMMC, SDIO wifi, SPI and Ardiuno shield. Only when we select
eMMC and SDIO wifi, the SDHC2 could be used. Otherwise, the command
inhibit bits of eSDHC2_PRSSTAT register will never release. This would
cause below continious error messages in linux since it uses polling
mode to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for RDB to disable
SDHC2 status if no SDIO wifi or eMMC is selected.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1012AQDS board has a hardware issue. When there is no eMMC
adapter card inserted in SDHC2 adapter slot, the command inhibit
bits of eSDHC2_PRSSTAT register will never release. This would cause
below continious error messages in linux since it uses polling mode
to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for QDS to
disable SDHC2 status if no eMMC adapter card is detected.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With entry_point now being an unsigned long we need to adapt the last
two debug prints to use %lX not %X.
Fixes: 11e1479b9e ("SPL: make struct spl_image 64-bit safe")
Signed-off-by: Tom Rini <trini@konsulko.com>
Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig
which is missing in below commit
"imx: mx6ull_14x14_evk: add plugin defconfig"
(sha1: b90ebf49bb)
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
On the MX6Q the aclk_eim_slow_podf field is '1' after POR, while on the
MX6DQP it is '3'.
This makes the EIM clock to be only 66MHz on the mx6qp variant, instead of
132 MHz.
Instead of relying on the POR values for the CSMR1 register, make sure to
manually configure the clk_eim_slow_sel field as '00' so that EIM clock is
derived from AXI clock and the aclk_eim_slow_podf field as '1' so that EIM
clock can be AXI clock divided by 2.
This way a consistent EIM clock frequency is configured for all the mx6
variants.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.
Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.
This is V2 of this patch with changes recommended by the maintainer
CC: Jagan Teki <jteki@openedev.com>
CONFIG_T104xRDB is defined in T104xRDB.h, so it is always enabled for
all T1040RDB, T1040D4RDB, T1042RDB, T1042D4RDB, T1042RDB_PI.
CONFIG_T104XD4RDB is defined for all T1040D4RDB, T1042D4RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_T1040D4RDB in Kconfig to simplify config macros. Replace
CONFIG_T1040D4RDB with TARGET_T1040D4RDB and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
All boards covered by this group have been converted to their own
targers. Drop TARGET_P1_P2_RDB_PC from Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P2020RDB_PC instead of sharing with P1_P2_RDB_PC to
simplify Kconfig and config macros.
Remove macro CONFIG_P2020RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1025RDB instead of sharing with P1_P2_RDB_PC to
simplify Kconfig and config macros.
Remove macro CONFIG_P1025RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1024RDB instead of sharing with TARGET_P1_P2_RDB_PC to
simplify Kconfig and macros.
Remove macro CONFIG_P1024RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1021RDB instead of sharing with TARGET_P1_P2_RDB_PC to
simplify Kconfig and macros.
Remove macro CONFIG_P1021RDB.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1020UTM instead of sharing with TARGET_P1_P2_RDB_PC
to simplify Kconfig and config macros.
Remove macro CONFIG_P1020UTM.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1020RDB_PD instead of sharing with P1_P2_RDB_PC
to simplify Kconfig and config macros.
Remove macro CONFIG_P1020RDB_PD.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1020RDB_PC instead of sharing with TARGET_P1_P2_RDB_PC
to simplify Kconfig and config macros.
Remove macro CONFIG_P1020RDB_PC.
Signed-off-by: York Sun <york.sun@nxp.com>
Use TARGET_P1020MBG instead of sharing with TARGET_P1_P2_RDB_PC to
simplify Kconfig and other macros.
Remove macro CONFIG_P1020MBG.
Signed-off-by: York Sun <york.sun@nxp.com>
Remove CONFIG_P1010RDB_PA and CONFIG_P1010RDB_PB and split TARGET_P1010RDB
to TARGET_P1010RDB_PA and TARGET_P1010RDB_PB in Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Change core clock to 1.2GHz in the configurations for SD and NAND boot.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current value to check whether the PHY was configured has dependency
on MC, it expects MC to start PCS AN, this is not true during boot up,
so it should be changed to remove the dependency.
The PHY's register space should be restore to default after accessing
extended space.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
The DP-DDR shouldn't be exposed as conventional memory to an OS, so let's
rather claim it's a reserved region in the EFI memory map
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
Add a README file to help users getting started with the board.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabresd design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.
This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add plugin code for mx6ullevk.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig file to use plugin code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a README to explain the steps for booting mx6sabresd in different ways:
1. Booting via Normal U-Boot (u-boot.imx)
2. Booting via SPL (SPL and u-boot.img)
3. Booting via Falcon mode (SPL launches the kernel directly)
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Allow i.MX6Q Sabre SD to load the kernel and dtb via SPL in Falcon mode.
Based on the Falcon mode code for MX6 Gateworks Ventana board.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
PBL flush command is restricted to CCSR memory space. So use WAIT
PBI command to provide enough time for data to get flush in
target memory.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York Sun: rewrap commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
T series boards use unified RCW for sd, spi and nand boot.
Now split txxx_rcw.cfg to txxx_sd_rcw.cfg, txxx_spi_rcw.cfg
and txxx_nand_rcw.cfg for SPI/NAND/SD boot.
And modify RCW[PBI_SRC] for them:
PBI_SRC=5 for SPI 24-bit addressing
PBI_SRC=6 for SD boot
PBI_SRC=14 for IFC NAND boot
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present there are two SPI functions only used by freescale which are
defined in the spi_flash.h header. One function name matches an existing
generic SPL function.
Move these into a private header to avoid confusion.
Arcturus looks like it does not actually support SPI, so drop the SPI code
from that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update the API's for transition of Security Monitor states. Instead
of providing both initial and final states for transition, just
provide final state for transition as Security Monitor driver will
take care of it internally.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[York Sun: Reformatted commit message slightly]
Reviewed-by: York Sun <york.sun@nxp.com>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When using SPL on i.mx6 we frequently notice some DDR initialization
mismatches between the SPL code and the non-SPL code.
This causes stability issues like the ones reported at 7dbda25ecd
("mx6ul_14x14_evk: Pass refsel and refr fields to avoid hang") and also:
http://lists.denx.de/pipermail/u-boot/2016-September/266355.html .
As the non-SPL code have been tested for long time and proves to be reliable,
let's configure the DDR in the exact same way as the non-SPL case.
The idea is simple: just use the DCD table and write directly to the DDR
registers.
Retrieved the DCD tables from:
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg
and
board/freescale/mx6sabresd/mx6qp.cfg
(NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga)
This method makes it easier for people converting from non-SPL to SPL code.
Other benefit is that the SPL binary size is reduced from 44 kB to 39.9 kB.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
SATA:
* SerDes2 Lane3 to SATA port
USB 3.0: one super speed USB 3.0 type A port
one Micro-AB port
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The deep sleep function of LS1 platform, is mapped into PSCI system
suspend function, this patch adds implementation of it.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add this API to make the individual device is able to be set to
the specified permission.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move forward the basic non-secure access enable operation, so the
subsequent individual device access permission can override it.
And collect the dispersed callers in board level, and then move
them to SoC level.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
sec_init() which was earlier called in misc_init_r()
is now done in board_init() before PPA init as SEC
block will be used during PPA image validation.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To be in the safe side we need to enable the CCGR clocks prior
to calling arch_cpu_init().
Inspired by Tim Harvey's commit d783c2744f ("imx: ventana: fix boot to SD").
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
Adjust DDR3 initialization done in SPL by comparing them against
the NXP DCD table.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
When running a NXP 4.1 kernel with U-Boot mainline on a mx6ul-evk,
we observe a hang when going into the lowest operational point of cpufreq.
This hang issue does not happen on the NXP U-Boot version.
After comparing the SPL DDR initialization against the DCD table
from NXP U-Boot, the key difference that causes the hang is the
MDREF register setting:
DATA 4 0x021B0020 0x00000800
,which means:
REF_SEL = 0 --> Periodic refresh cycle: 64kHz
REFR = 1 ---> Refresh Rate - 2 refreshes
So adjust the MDREF initialization for mx6ul_evk accordingly
to fix the kernel hang issue at low bus frequency.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need
to do a read-modify-write operation.
Simplify the code by writing directly to this register.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need
to do a read-modify-write operation.
Simplify the code by writing directly to this register.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Only a single pad is changed to change sdhc2_dat3 from an
SDIO pin to and from GPIO4:5, so remove the array and use
the imx_iomux_v3_setup_pad() routine.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
mx7dsabresd has two targets:
- mx7dsabresd_defconfig: boots in non-secure mode
- mx7dsabresd_secure_defconfig: boots in secure mode
Print the mode that is being used to help users to easily identify
which target is running on the board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
QSPI and IFC are pin-multiplexed on LS1043AQDS board. If QSPI is
enabled, IFC would not be initialized correctly. So disable the IFC
node for Linux.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
psci_version,
psci_features,
psci_cpu_suspend,
psci_affinity_info,
psci_system_reset,
psci_system_off.
Tested on LS1021aQDS, LS1021aTWR.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add SD secure boot target for ls1021atwr.
Implement board specific spl_board_init() to setup CAAM stream ID and
corresponding stream ID in SMMU. Change the u-boot size defined by a
macro for copying the main U-Boot by SPL to also include the u-boot
Secure Boot header size as header is appended to u-boot image. So header
will also be copied from SD to DDR.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Override jump_to_image_no_args function to include validation of
u-boot image using spl_validate_uboot before jumping to u-boot image.
Also define macros in SPL framework to enable crypto operations.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
The changes are similar to
commit 467a40dfe3
powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA use PSCI to make secondary cores bootup. So when PPA was
enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method
between PSCI and spin-table.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
The LBMAP switches on the board will tell which boot device is used.
Only QSPI boot is supported if the boot device is IFCCard.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current pad DSE for QSPI is 60ohm. This setting cause
too strong drive to clock and data signals. Need to change
the DSE to 120ohm for better signal quality.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3.
If LCD_nPWREN is high, output is 2.4V which is not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fix 74LV OE gpio index. gpio index is wrong,
so gpio output will not have effect, since we
use wrong GPIO5_IO18, but not correct GPIO5_IO8.
And at the end of the initialization of 74lv init, should
keep OE voltage level at LOW to make 74lv output the correct
voltage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect
D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3
is actually 1.2V.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently the LVDS backlight does not work in U-Boot after a “reboot” comand
in the kernel.
This problem occurs because the kernel uses this pin in PWM mode and U-Boot
does not configure the backlight pin as GPIO functionality.
So fix the problem by explicitly configuring the backlight pin as GPIO in
U-Boot.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When QSPI is enabled, NOR flash and QIXIS can't be accessed
through IFC due to pin mux. Enable I2C QIXIS access and I2C
early init to read the sysclk and ddrclk.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
No intended functional change, just remove redundancies in some
Makefiles, and make whitespace aesthetics uniform.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
We should use unified setup_ddr_tlbs() for spl boot and non-spl boot
to make sure 'M' bit is set for DDR TLB to maintain cache coherence.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For malloc to work in SPL framework enable GD_FLG_FULL_MALLOC_INIT
flag in global data after allocating memory using mem_malloc_init.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add QIXIS_LBMAP_BRDCFG_REG to the save offset of LBMAP
configuration register instead of hardcoding it in
set_lbmap() function.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check if qixis supports memory-mapped read/write
before compiling IFC based qixis read/write functions.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc
Also move README.lsch2 and README.lsch3 in same folder.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SCFG_USBPWRFAULT_DEDICATED instead of SCFG_USBPWRFAULT_SHARED should
be used for USB 3 & 2.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS102A ref manual dictates that ICID have to be written to the MSB
of the ICID register, not to the LSB.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
This patch updates clk_adjust to actual value for boards with
T-series and LS-series SoCs to match the setting of clk_adjust
in latest ddr driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In 'commit d584c68ce0f5bf2f430ccfb2ba00bd506206fb91',
ar8031 is changed to use ar8035_config. ar8035_config
actually does the same thing as mx6_rgmii_rework, so
drop mx6_rgmii_rework and board_phy_config.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:
config OF_BOARD_SETUP
bool "Set up board-specific details in device tree before boot"
depends on OF_LIBFDT
...
remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5,
FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6.
Signed-off-by: Ying Zhang <ying.zhang22455@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity
by setting relative bit in SCFG_INTPCR register, because AQR105
interrupt is low active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using u16 for cfg_rcw_src and u8 for sd1refclk_sel is enough.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
gd->env_addr will be initialized in env_init() in
common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined.
So no need to do it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current 'cpld reset' will just write global_rst register
but couldn't switch to NOR boot if the board's switches are
for NAND/SD boot. So need to write rcw source registers for
NOR boot as well.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Mix usage of uint32_t and u32 fixed in favor of u32.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On the LS102x boards, in order to initialize the ICID values of
masters, the dev_stream_id array holds absolute offsets from the
base of SCFG.
In ls102xa_config_ssmu_stream_id, the base pointer is cast to
uint32_t * before adding the offset, leading to an invalid address.
Casting it to void * solves the issue.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update MAINTAINERS file for ls2080aqds and ls2080ardb platforms.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Optimize DDR timing for good margins to support new Transcend
and Apacer DDR4 UDIMM besides current Micron UDIMM.
Verified 1333MT/s, 1600MT/s, 1866MT/s, 2133MT/s rate with
following UDIMM on LS2080ARDB.
- Micron UDIMM: MTA18ASF1G72AZ-2G1A1Z
- Apacer UDIMM: 78.C1GM4.AF10B
- Transcend UDIMM: TS1GLH72V1H
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
When setting fixed-link property to DTS, the values should be converted
with using cpu_to_fdt32 so that to have correct value on little endian
Soc.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Having had a similar board and memory part under logic analyzer, a
tINIT3 violation was measured. The fix was involved keeping tXPR and
SDE_to_RST at the power-on defaults and setting RST_to_CKE the JEDEC
value for LPDDR2. There was also a tIH-CA violation and this was
resolved by writing the default value in rather than what the script
here uses.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Having had a similar board and memory part under logic analyzer, a
tINIT3 violation was measured. The fix was involved keeping tXPR and
SDE_to_RST at the power-on defaults and setting RST_to_CKE the JEDEC
value for LPDDR2.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
enable_lvds() function only set bits IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT and
IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT, but these bits were already set
previously inside setup_display().
We can safely remove enable_lvds() then.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use a pointer to pass image address to fsl_secboot_validate(),
instead of using environmental variable "img_addr".
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case of fatal failure during secure boot execution (e.g. header
not found), reset is asserted to stop execution. If the RESET_REQ
is not tied to HRESET, this allows the execution to continue.
Add esbh_halt() after the reset to make sure execution stops.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sec_init has been called at the beginning to initialize SEC Block
(CAAM) which is used by secure boot validation later for both ls2080a
qds and rdb. 64-bit address in ESBC Header has been enabled. Secure
boot defconfigs are created for boards (NOR boot).
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For secure boot, a header is used to identify key table, signature
and image address. A new header structure is added for lsch3.
Currently key extension (IE) feature is not supported. Single key
feature is not supported. Keys must be in table format. Hence, SRK
(key table) must be present. Max key number has increase from 4 to
8. The 8th key is irrevocable. A new barker Code is used.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
VESA 1024x768 results in much more accurate timings.
Based on the patch from Soeren Moch for the tbs2910 board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The fsl-mc node has been moved under /soc, so update
the path references accordingly. Backwards compatibility
is retained for /fsl-mc.
Delete backwards compatibility for the completely obsolete
/fsl,dprc@0.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Return i2c mux to the default channel after accessing retimer.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IR chip is on one of the channels on multiplexed I2C-bus.
Reset to default channel after accessing.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As phy_connect and phy_config are being called from DPAA2 driver.
Remove calling of mentioned function from board file.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins
polarity by setting IRQCR register, because AQR405 interrupt is low
active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
GPIO4_21 is the LAN8720 power pin, not the LAN8720 reset pin.
Fix that, so that we can have Ethernet functional again.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The initialization for smmu and stream id is moved into the common soc
code.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QE-HDLC and USB multi-use the pins, modify the pin-muxing code
for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins
to QE-HDLC, if not, assgin it to USB
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Pin-muxing code should be in config_board_mux, move USB muxing
config to config_board_mux.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When running the 'ums' command we get:
=> ums 0 mmc 0
UMS: disk start sector: 0x0, count: 0xe18000
g_dnl_register: failed!, error: -22
ERROR: g_dnl_register failed
at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage()
Fix this by initializing USB OTG1 port as USB device mode instead of host.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Implement board_mmc_get_env_dev for the boards.
Following is examples:
SD1/SD2/SD3: return devno;
SD2/SD3: return devno - 1;
SD2/SD4: if (devno == 2), return dev - 2; return dev - 1;
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1
port, enable this display feature by adding relevant BSP codes
and configurations.
Signed-off-by: Ye Li <ye.li@nxp.com>
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card.
Fixed the value to correct one.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.
So do as suggested in order to have Ethernet working again.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
