The new ELF decoding logic assumed that the target binary has the same
endianness as the host, which broke building ARM64 firmware binaries on
big-endian machines.
This commit fixes the ELF64 decoding to be host-endianness-neutral, and
applies the same changes to the ELF32 decoding. It does not fix the
microblaze-specific dynamic symbol decoding.
It also corrects the functions used for byte swapping in rela_elf64()
and rela_elf32(). The result is the same, but semantically the code is
converting bytes read from a foreign-endianness file to host byte order.
Fixes: 4c9e2d6434 ("tools: relocate-rela: Read rela start/end directly from ELF")
Fixes: a1405d9cfe ("tools: relocate-rela: Check that relocation works only for EM_AARCH64")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220715064026.54551-1-samuel@sholland.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
The x509 certificate SWRV is currently hard-coded to 0. This need to be
updated to 1 for j721e 1.1, j7200 and am64x. It is don't care for other
k3 devices.
Added new config K3_X509_SWRV to k3. Default is set to 1.
Signed-off-by: Yogesh Siraswar <yogeshs@ti.com>
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The BootROM of MT7621 requires a image header for SPL to record its size
and load address when booting from NAND.
To create such an image, one can use the following command line:
mkimage -T mtk_image -a 0x80200000 -e 0x80200000 -n "mt7621=1"
-d u-boot-spl-ddr.bin u-boot-spl-ddr.img
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mkimage command has had many options added over the years.
Unfortunately, we are starting to run out of short options. Recent options
don't have any obvious relation to their meaning (e.g. -o/-g). Fortunately,
long options exist. Add long options for each current short option.
For the curious, the remaining short options are HIkLmMPQSuUwWXyYzZ.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A new DT binding for describing environment data block has been added in
Linux's commit 5db1c2dbc04c ("dt-bindings: nvmem: add U-Boot environment
variables binding"). Once we get a proper Linux NVMEM driver it'll be
possible to use Linux's binary interface for user-space as documented
in the:
https://www.kernel.org/doc/html/latest/driver-api/nvmem.html
This commits makes fw_env fallback to looking for a compatible NVMEM
device in case config file isn't present. In a long term this may make
config files redundant and avoid code (info) duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The documentation above the DEFINE_ALIGN_BUFFER says it's for use
outside functions, but we're inside one.
Instead use ALLOC_CACHE_ALIGN_BUFFER, the stack based macro, which also
includes the cache alignment.
Fixes: b583348ca8 ("image: fit: Align hash output buffers")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Binman lets us declare symbols in SPL/TPL that refer to other entries in
the same binman image as them. These symbols are filled in with the
correct values while binman assembles the images, but this is done
in-memory only. Symbols marked as optional can be filled with
BINMAN_SYM_MISSING as an error value if their referred entry is missing.
However, the unmodified SPL/TPL binaries are still available on disk,
and can be used by people. For these files, nothing ensures that the
symbols are set to this error value, and they will be considered valid
when they are not.
Empirically, all symbols show up as zero in a sandbox_vpl build when we
run e.g. tpl/u-boot-tpl directly. On the other hand, zero is a perfectly
fine value for a binman-written symbol, so we cannot say the symbols
have wrong values based on that.
Declare a magic symbol that binman always fills in with a fixed value.
Check this value as an indicator that symbols were filled in correctly.
Return the error value for all symbols when this magic symbol has the
wrong value.
For binman tests, we need to make room for the new symbol in the mocked
SPL/TPL data by extending them by four bytes. This messes up some test
image layouts. Fix the affected values, and check the magic symbol
wherever it makes sense.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Enabling CONFIG_BINMAN makes binman run after a build to package any
images specified in the device-tree. It also enables a mechanism for
SPL/TPL to declare and use special linker symbols that refer to other
entries in the same binman image. A similar feature that gets this info
from the device-tree exists for U-Boot proper, but it is gated behind a
CONFIG_BINMAN_FDT unlike the symbols.
Confusingly, CONFIG_SPL/TPL_BINMAN_SYMBOLS also exist. These configs
don't actually enable/disable the symbols mechanism as one would expect,
but declare some symbols for U-Boot using this mechanism.
Reuse the BINMAN_SYMBOLS configs to make them toggle the symbols
mechanism, and declare symbols for the U-Boot phases in a dependent
BINMAN_UBOOT_SYMBOLS config. Extend it to cover symbols of all phases.
Update the config prompt and help message to make it clearer about this.
Fix binman test binaries to work with CONFIG_IS_ENABLED(BINMAN_SYMBOLS).
Co-developed-by: Peng Fan <peng.fan@nxp.com>
[Alper: New config for phase symbols, update Kconfigs, commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
At present tag numbers are only allocated for non-core data, meaning that
the 'core' data, like priv and plat, are accessed through dedicated
functions.
For debugging and consistency it is convenient to use tags for this 'core'
data too. Add support for this, with new tag numbers and functions to
access the pointer and size for each.
Update one of the test drivers so that the uclass-private data can be
tested here.
There is some code duplication with functions like device_alloc_priv() but
this is not addressed for now. At some point, some rationalisation may
help to reduce code size, but more thought it needed on that.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this driver uses 'priv' struct to hold 'plat' data, which is
confusing. The contents of the strct don't matter, since only dtoc is
using it. Create a new struct with the correct name.
Signed-off-by: Simon Glass <sjg@chromium.org>
On python 3.8.10 (and 3.10), subparsers are not updated with defaults. I
suspect this is related to [1]. Fix this by explicitly updating
subparsers with settings.
[1] https://github.com/python/cpython/issues/89398
Fixes: 3145b63513 ("patman: Update defaults in subparsers")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Tested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
While running tests for a python tool, the tests' outputs get printed in
whatever order they happen to run, without any indication as to which
output belongs to which test. Unittest supports capturing these outputs
and printing them as part of the test summaries, but when a failure or
error occurs it switches back to printing as the tests run. Testtools
and subunit tests can do the same as their parts inherit from unittest,
but they don't outright expose this functionality.
On the unittest side, enable output buffering for the custom test result
class. Try to avoid ugly outputs by not printing stdout/stderr before
the test summary for low verbosity levels and for successful tests.
On the subunit side, implement a custom TestProtocolClient that enables
the same underlying functionality and injects the captured streams as
additional test details. This causes them to be merged into their test's
error traceback message, which is later rebuilt into an exception and
passed to our unittest report class.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default, unittest test summaries only print extended info about tests
that failed or couldn't run due to an error. Use a custom text result
class to print info about more cases: skipped tests, expected failures
and unexpected successes.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
The python tools' test utilities handle printing test results, but the
output is quite bare compared to an ordinary unittest run. Delegate
printing the results to a unittest text runner, which gives us niceties
like clear separation between each test's result and how long it took to
run the test suite.
Unfortunately it does not print info for skipped tests by default, but
this can be handled later by a custom test result subclass. It also does
not print the tool name; manually print a heading that includes the
toolname so that the outputs of each tool's tests are distinguishable in
the CI output.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's possible to request a specific test to run when trying to run a
python tool's tests. If we request a nonexistent test, the unittest
loaders generate a fake test that reports this as an error. However, we
get these fake tests even when the test exists, because test_util can
load tests from multiple places one by one and the test we want only
exists in one.
The test_util helpers currently remove these fake tests when printing
test results, but that's more of a workaround than a proper solution.
Instead, don't even try to load the missing tests.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When printing a python tool's test results, the entire list of failed
tests and their tracebacks are reprinted for every failed test. This
makes the test output quite unreadable. Fix the loop to print failures
and tracebacks one at a time.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the common functions to run tests and report results. Ensure that the
result code indicates success or failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
There is no reason to do serial initialization. Uart driver does it
already based on DT. Good effect is that it is clear which interface is
console.
The resulting change was done in past by commit 84d2bbf082 ("arm64:
zynqmp: Remove low level UART setting").
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220620163650.18756-12-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Microblaze is 32bit that's why it is using elf32 format. Relocation code
requires to get information about rela and dynsym senctions and also text
base which was used for compilation.
Code build with -fPIC and linked with -pic generates 4 relocation types.
R_MICROBLAZE_NONE is the easiest one which doesn't require any action.
R_MICROBLAZE_REL only requires write addend to r_offset address.
R_MICROBLAZE_32/R_MICROBLAZE_GLOB_DAT are the most complicated. There is a
need to find out symbol value with adding symbol value and write it to
address pointed by r_offset. Calculation with addend is also added but
only 0 addend values are generated now.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9912c3d76933bdf75e1ebb6aab43726cd32cafb5.1655299267.git.michal.simek@amd.com
Adding support for new type requires to change code layout that's why move
elf64 code to own function for easier maintenance.
It also solves the problem with not calling fclose in case of error.
Return value from rela_elf64 is saved to variable that's why fclose() is
called all the time.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/21763b80527521c85ca7d4ac64ad6ff4885409c8.1655299267.git.michal.simek@amd.com
There is no need to pass section information via parameters.
Let's read text base and rela start/end directly from elf.
It will help with reading other information from ELF for others
architecture. Input to relocate-rela is u-boot binary and u-boot ELF.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ab7ae14a6e058722e8c608089729e98edf20a08d.1655299267.git.michal.simek@amd.com
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This test was written to match up with the list of compatibles in
drivers/i2c/tegra_i2c.c so adding another one requires the test to be
updated to match.
Fixes: 0d2105ae5e ("arm: tegra: Update some DT compatibles")
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for signing images in auto-generated FITs. To do this,
we need to add a signature node. The algorithm name property already has
its own option, but we need one for the key name hint. We could have
gone the -G route and added an explicit name for the public key (like
what is done for the private key). However, many places assume the
public key can be constructed from the key dir and hint, and I don't
want to do the refactoring necessary.
As a consequence of this, it is now easier to add public keys to an
existing image without signing something. This could be done all along,
but now you don't have to create an its just to do it. Ideally, we
wouldn't create a FIT at the end. This could be done by calling
fit_image_setup_sig/info.crypto->add_verify_data directly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Building with OpenSSL 3.0 produces warnings like:
../tools/sunxi_toc0.c:846:17: warning: ‘RSA_get0_d’ is deprecated:
Since OpenSSL 3.0 [-Wdeprecated-declarations]
846 | if (root_key && RSA_get0_d(root_key)) {
| ^~
As OpenSSL 3.0 is not available in elder Linux distributions
just silence the warning.
Add missing #include <openssl/bn.h>.
Fixes: e9e87ec47c ("tools: mkimage: Add Allwinner TOC0 support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Over the years, several options have not made it into the help message.
Document them. Do the same for the man page.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
On some image types like i.MX8 and i.MX8M, the verify_header function
is not implemented.
Before this commit, no check on tparams->verify_header was done causing
a segfault if NULL. Now, a proper error message is printed.
Signed-off-by: Nicolas Heemeryck <nicolas.heemeryck@gmail.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
'make tests' fails on Ubuntu 22.04 with:
binman: ./tools/binman/binman:12: DeprecationWarning:
The distutils package is deprecated and slated for removal in Python 3.12.
Use setuptools or check PEP 632 for potential alternatives
from distutils.sysconfig import get_python_lib
./tools/binman/binman:12: DeprecationWarning:
The distutils.sysconfig module is deprecated, use sysconfig instead
from distutils.sysconfig import get_python_lib
<unittest.result.TestResult run=428 errors=0 failures=4>
AssertionError: 0 != 468
As we don't use Ubuntu 16.04 for our CI anymore drop the import.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Binman interfaces allow attempts to replace any entry in the image with
arbitrary data. When trying to replace sections, the changes in the
section entry's data are not propagated to its child entries. This,
combined with how sections rebuild their contents from its children,
eventually causes the replaced contents to be silently overwritten by
rebuilt contents equivalent to the original data.
Add a simple test for replacing a section that is currently failing due
to this behaviour, and mark it as an expected failure. Also, raise an
error when replacing a section instead of silently pretending it was
replaced.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A previous patch fixes binman to correctly extract FIT subentries. This
makes it easier to test replacing these entries as we can write tests
using an existing helper function that relies on extracting the replaced
entry.
Add tests that replace leaf entries in FIT subsections with data of
various sizes. Replacing the subsections or the whole FIT section does
not work yet due to the section contents being re-built from unreplaced
subentries' data.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When reading images from a file, each entry's data is read from its
parent section as specified in the Entry.Create() call that created it.
The FIT entry type has been creating its subentries under its parent
(their grandparent), as creating them under the FIT entry resulted in an
error until FIT was converted into a proper section.
FIT subentries have their offsets relative to the FIT section, and
reading those offsets in the parent section results in wrong data. The
subentries rightfully belong under the FIT entries, so create them
there. Add tests checking that we can extract the correct data for a FIT
entry and its subentries.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Binman FIT entry nodes describe their subentries in an 'images' subnode,
same as how they would be written for the mkimage executable. The entry
type initially manually managed its subentries keyed by their node paths
relative to its base node. It was later converted to a proper section
while still keeping the same keys for subentries.
These subentry keys of sections are used as path fragments, so they must
not contain the path separator character '/'. Otherwise, they won't be
addressable by binman extract/replace commands. Change these keys from
the '/images/foo' forms to the subentry node names. Extend the simple
FIT tests to check for this.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
When an image has the 'allow-repack' property, binman includes the
original offset and size properties from the image description in the
fdtmap. These are later used as the packing constraints when replacing
entries in an image, so other unconstrained entries can be freely
positioned.
Replacing an entry in an image without 'allow-repack' (and therefore the
original offsets) follows the same logic and results in entries being
merely concatenated. Instead, skip resetting the calculated offsets and
sizes to the missing originals for these images so that every entry is
constrained to its existing offset/size.
Add tests that replace an entry with smaller or equal-sized data, in an
image that doesn't allow repacking. Attempting to do so with bigger-size
data is already an error that is already being tested.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
