At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
Add a new 'font' command which allows the fonts to be listed as well as
selecting a different font and size.
Allow the test to run on sandbox, where multiple font/size combinations
are supported, as well as sandbox_flattree, where they are not.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a couple of places the document says u-boot,pre-reloc but all
examples show u-boot,dm-pre-reloc, use the latter consistently.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
GPMC stands for General Purpose Memory Controller and it is
present on many Texas Instruments SoCs.
It supports a number of Asynchronous and Synchronous interfaces
and has various settings to configure the bus interface.
The DT bindings define all the various GPMC settings.
As the GPMC supports multiple devices on the bus, each
device is represented as a child and the respective
GPMC settings are situated there. (see ti,gpmc-child.yaml)
These binding docs are picked up from the Linux kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
This is a companion to u-boot,noautostart. If one has a single
watchdog device that one does want to have auto-started, but several
others that one doesn't, the only way currently is to set the
CONFIG_WATCHDOG_AUTOSTART and then use the opt-out for the majority.
The main motivation for this is to add an autostarted watchdog device
to the sandbox (to test a fix) without having to set AUTOSTART in
sandbox_defconfig and add the noautostart property to the existing
devices. But it's also nice for symmetry, and the logic in
init_watchdog_dev() becomes simpler to read because we avoid all the
negations.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There are no platforms that have not migrated to using DM_KEYBOARD,
remove the legacy option.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
When a FIT includes some OS requests, U-Boot should process these and add
the requested info to corresponding subnodes of the /chosen node. Add a
pytest for this, which sets up the FIT, runs bootm and then uses a C
unit test to check that everything looks OK.
The test needs to run on sandbox_flattree since we don't support
device tree fixups on sandbox (live tree) yet. So enable BOOTMETH_VBE and
disable bootflow_system(), since EFI is not supported on
sandbox_flattree.
Add a link to the initial documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update this function's comment and also the livetree documentation, so it
is clear when to use the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The working FDT is the one which comes from the OS and is fixed up by
U-Boot. When the bootm command runs, it sets up the working FDT to be the
one it is about to pass to the OS, so that fixups can happen.
This seems like an important step, so add a message indicating that the
working FDT has changed. This is shown during the running of the bootm
command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add xxd command to print file content as hexdump to standard out
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Roger Knecht <rknecht@pm.me>
This adds keyword devicetree-overlay as an alias for fdtoverlays in
extlinux (sysboot) and pxe to better follow the Boot Loader Specification
[1], improves documentation around them by adding an example for both
fdtoverlays and devicetree-overlay and the environment variable required
for this feature. The link for the spec is updated to the current one.
[1] https://systemd.io/BOOT_LOADER_SPECIFICATION/
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We want tests to avoid the usage of sudo. Describe that virt-make-fs can
generate disk images without being root.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Packages python3-filelock python3-pytest-xdist as required to run
'make tests'. Add them to the required packages list in the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the cls command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The XTRN_DECLARE_GLOBAL_DATA_PTR declarations in ppc code are permanently
commented out, so there are no users for this macro:
#if 1
#define DECLARE_GLOBAL_DATA_PTR register volatile gd_t *gd asm ("r2")
#else /* We could use plain global data, but the resulting code is bigger */
#define XTRN_DECLARE_GLOBAL_DATA_PTR extern
#define DECLARE_GLOBAL_DATA_PTR XTRN_DECLARE_GLOBAL_DATA_PTR \
gd_t *gd
#endif
Remove all references to this macro, but add a documentation note regarding
the possibility of using plain global data for the GD pointer.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
* Convert code comments in include/efi_driver.h to Sphinx style.
* Add include/efi_driver.h to the HTML documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present ofnode_write_prop() is inconsistent between livetree and
flattree, in that livetree requires the caller to ensure the property
value is stable (e.g. in rodata or allocated) but flattree does not, since
it makes a copy.
This makes the API call a bit painful to use, since the caller must do
different things depending on OF_LIVE.
Add a new 'copy' argument which tells the function to make a copy if
needed. Add some tests to cover this behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current tests do not cover all functions, nor do they cover the new
multi-tree functionality. Add and update the tests accordingly and update
the 'future work' notes in the documentation.
There is a still more testing needed for the failure cases, since at
present some ofnode functions return a libfdt error code instead of
converting it to an errno.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the logic to redirect requests for the device tree through a function
which can look up the tree ID. This works by using the top bits of
ofnode.of_offset to encode a tree.
It is assumed that there will only be a few device trees used at runtime,
typically the control FDT (always tree ID 0) and possibly a separate FDT
to be passed the OS.
The maximum number of device trees supported at runtime is 8, with this
implementation. That would use bits 30:28 of the node-offset value,
meaning that the positive offset range is limited to bits 27:0, versus
30:1 with this feature disabled. That still allows a device tree of up
to 256MB, which should be enough for most FITs. Larger ones can be
supported by using external data with the FIT, or by enabling OF_LIVE.
Update the documentation a little and fix up the comment for
ofnode_valid().
Signed-off-by: Simon Glass <sjg@chromium.org>
Complete the list of commands influenced by the autostart environment
variable.
Make it clearer what values qualifies at 'yes'.
Eventually the list of environment variables is to be alphabetically
sorted. Move autostart up.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the flat device tree changes it can mess up the live tree since that
uses the flat tree for its strings. This affects only a few sandbox tests
which modify the device tree, but the number will grow as ofnode support
for writing improves.
While the control FDT is not intended to change while U-Boot is running,
some tests do so. For example, the ofnode interface only supports
modifying properties in the control FDT, so tests must use that.
To solve this problem, keep a copy of the FDT and restore it as needed
when the test is finished. The copy only happens on sandbox (except SPL
builds), to reduce memory usage and because these tests are not useful on
other boards. For other boards, a checksum is taken to ensure that nothing
changes.
It would be possible to always checksum the FDT on sandbox and only
restore it if needed, but this is slightly slower than restoring it every
time, at least with crc8.
Move the code which checks for success to the very end, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running the script to sign SPL/U-Boot on a kontron-sl-mx8mm board,
the fit_block_size was calculated as 0x1000 instead of 0x1020.
Add an extra parenthesis pair to fix it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add HABv4 documentation extension for SPL targets covering the
following topics:
- How to sign an securely boot an flash.bin container image.
- How to extend the root of trust for additional boot images.
- Add SPL and fitImage CSF examples.
- Add signature generation script example.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Disable UBI fastmap support which is not supported by original Maemo 5
kernel and explicitly set UBI BEB limit to 10%, which is the value used by
original Maemo 5 kernel. U-Boot default value is 20%.
Signed-off-by: Pali Rohár <pali@kernel.org>
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
-----BEGIN PGP SIGNATURE-----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=P89S
-----END PGP SIGNATURE-----
Merge tag 'efi-next-2022-09-14' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi next
UEFI:
Implement a command eficonfig to maintain Load Options and boot order via
menus.
The bootmenu enumerates the UEFI boot options
for boot device selection.
This commit adds the description how the UEFI boot work
in bootmenu. This commit also adds "Synopsis", "Description"
and "Configuration" sections to follow the U-Boot command
documentation format.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add documentation for the cyclic function infrastructure, including the
cyclic command.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Running tests in parallel is much faster, e.g. 15 seconds to run the tests
on sandbox (only), instead of 100 seconds (on a 16-core machine). Add a
'make pcheck' option to access this feature.
Note that the tools/ tests still run each tool's tests once after the
other, although within that, they do run in parallel. So for example,
the buildman tests run in parallel, then the binman tests run in
parallel. There would be a signiificant advantage to running them all
in parallel together, but that would require a large amount of
refactoring, e.g. with more use of pytest fixtures.
Update the documentation to represent the current state.
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* man-page for tftpput
UEFI:
* fix driver binding protocol for block IO devices
* don't delete invalid handles
* add a unit test for the EFI Conformance Profile Table
Other:
* correct short text for tftpboot
-----BEGIN PGP SIGNATURE-----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=1zZW
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-10-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-10-rc5
Documentation:
* man-page for tftpput
UEFI:
* fix driver binding protocol for block IO devices
* don't delete invalid handles
* add a unit test for the EFI Conformance Profile Table
Other:
* correct short text for tftpboot
Provide a man-page for the tftpput command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some tests can have race conditions which are hard to detect on a single
one. Add a way to run tests more than once, to help with this.
Each individual test is run the requested number of times before moving
to the next test. If any runs failed, a message is shown.
This is most useful when running a single test, since running all tests
multiple times can take a while.
Signed-off-by: Simon Glass <sjg@chromium.org>
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
Add bindings needed for accessing the FWU metadata regions.
These include the compatible string which point to the access
method, the actual device which stores the FWU metadata and
the offsets for both metadata regions.
The current patch adds basic bindings needed for accessing the
metadata structure on non-GPT mtd regions.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
- Use gender-neutral language to refer to the user, consistently.
- Reference the checkpatch document.
- Move the section on commit message tags to the process document and
reference this in sending_patches.rst.
- Reword the custodian workflow process section to refer to this new
section, integrate some of the wording from there in this new section.
- Update the comment about GPLv2 applying to August 2022, to be clear
this still is correct.
- Reword the section about MAKEALL to talk about local build testing and
link to the CI document.
- Reference the system_configuration document for the note about
modifying existing code.
- Reword the patchwork flow section.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Import as-is much of the old "Patches" wiki page to the current
sending_patches.rst file. This means we need to move patman to being
included in the higher level ToC and add a reference for "Custodians" in
the process document. A very minimal amount of content changing and
rewording is done here as part of the import, in order to make the
conversion easier.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add gpio status output fields description and one output example.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tweak the formatting.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
With the addition of the revision stats this now takes over a minute. Use
a parallel build to reduce it a bit (24 seconds for me).
Series-changes; 2
- Use '-j auto' instead
Signed-off-by: Simon Glass <sjg@chromium.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Explain when devices should get activated.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The ELF U-Boot image produced by qemu-riscv64_smode_defconfig can be
used to boot with QEMU and KVM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is an attempt to answer the comments provided by Xavier [1].
[1] https://lore.kernel.org/all/Yulcol7HpTHtjXTX@begut/
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Link to patman's documentation from the doc/ directory so that it appears
in the 'make htmldocs' output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This was widely used by U-Boot for a long time, but is not used anymore,
with Gitlab and Azure taking over.
Drop the text.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We talk about importing code from other projects in two places. The
first place is in the coding style section, where we explain when to or
not to deviate in terms of white space, etc. In the process
documentation we now add a note about saying where the code was imported
from and to ensure that you do not copy Signed-off-by or other tags.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* describe crashs in UEFI binaries
* provide architechture specific information for the sandbox and RISC-V
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These typos were found while reading the docs.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Remove alias 'efi' with invalid data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some documentation and a new flag so that we can safely enabled using
the ofnode interface to write to the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
The unflattening algorithm results in a single block of memory being
allocated for the whole tree. When writing new properties, these are
allocated new memory outside that block. When the block is freed, the
allocated properties remain.
Document how this works and the potential memory leak, as well as
mentioning that updating the livetree is actually supported now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few links to documents about Verified Boot for Embedded (VBE).
These will be expanded as development proceeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not needed now that CONFIG_SYS_TARGET_NAME is correctly determined
when scanning Kconfig.
This reverts commit 25b8acee2e.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a large number of options under CONFIG_SYS (but some of these
are elsewhere, spotted while cleaning CONFIG_SYS) that are never
referenced, or only used slightly later in the config file. Remove or
restructure these.
Signed-off-by: Tom Rini <trini@konsulko.com>
Start by describing in general the best practices for how to implement
configuration of some aspect of U-Boot. This generally means finding
the right choices for when something should be static or dynamically
configured and enabled. Then further document when to use CONFIG or CFG
namespaces for static configuration.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Describe exactly which bytes are hashed and in what order
when signing a configuration.
Signed-off-by: Martin Bonner <martingreybeard@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Start by elaborating on what some of our constraints tend to be with
image location values, and document where these external constraints
can come from. Provide a new subsection, an example based on the TI
ARMv7 OMAP2PLUS families of chips, that gives sample values and explains
why we use these particular values. This is based on what is in
include/configs/ti_armv7_common.h as of fb3ad9bd92 ("TI: Add, use a
DEFAULT_LINUX_BOOT_ENV environment string") as this contains just the
values referenced in this document now and not some of the further
additions that are less generic.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
When CONFIG_LOG is activated, if LOG_DEBUG is defined in a file and
DEBUG is not defined the trace with debug() macro are not displayed,
because the parameter cond : _DEBUG = 0 is checked in debug_cond().
With this patch the define DEBUG, used to force the trace generated by
debug() macro, is linked with the define LOG_DEBUG, used to force the
trace generated by other macros (log_debug, dev_dbg, pr_debug).
We only need to define LOG_DEBUG in a file to activate all the
traces generated by any U-Boot debug macro, as it is described in
/doc/develop/logging.rst
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add supporting new compatible string "u-boot,zynqmp-fpga-enc" to
handle loading encrypted bitfiles.
This feature requires encrypted FSBL, as according to UG1085:
"The CSU automatically locks out the AES key, stored in either BBRAM
or eFUSEs, as a key source to the AES engine if the FSBL is not
encrypted. This prevents using the BBRAM or eFUSE as the key source
to the AES engine during run-time applications."
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-14-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add instructions to build and boot from QSPI Flash
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
%s/formatted/format/
Fixes: 4211fb2ef6 ("doc: Migrate CodingStyle wiki page to Sphinx")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The wiki had gitdm-generated release statistics starting with v1.3.0.
Re-generate this information as Sphinx. This aims to be as historically
accurate as possible and so some company renames were kept to their old
rather than current name until we had made the switch previously.
Signed-off-by: Tom Rini <trini@konsulko.com>
For quite a long time we've been using a 3 week, rather than 2 week,
merge window as it was only 2 weeks during the timeframe where we did 2
month rather than 3 month releases. This corrects the places that still
had 2 weeks and tries to make things a bit clearer overall.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the RelaseCycle wiki page to Sphinx. In terms of visible
changes, we stop having a dynamic countdown to when the release is. And
we drop the year-based statistics, that were not being kept up to date.
For the moment, we only link to statistics for v2022.07 but will add
back the historical data in a subsequent patch.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "Workflow of a Custodian" section on the wiki had not been changed
in quite some time to reflect how the process has been functioning for
some time. First, update some links to point to modern and current
sources of information.
Second, and more overarching, reword much of the section. This expands
on the expectations of both custodians and developers when it comes to
rebasing patches. Rework the final points to be clearer that Custodians
are expected to do their best to test the changes and ask for help when
needed, as well as that pull requests are expected in a timely manner.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Use gender-neutral language to refer to the user, consistently.
- Reword a few places so that they read more naturally.
- Make the long standing practice around "Twilight Time" more clear,
hopefully.
- Replace a reference to MAKEALL with a reference to CI testing as
that's the current requirement.
Cc: Claudius Heine <ch@denx.de>
Cc: Martin Bonner <martingreybeard@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Remove some missed wiki markup, and escape a "\n" correctly.
- Use gender-neutral language to refer to the user, consistently.
Cc: Claudius Heine <ch@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current Process wiki page to doc/develop/process.rst. The
changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
For some time now we've allowed for '//' style comments, which mirrors
the Linux kernel. So drop this point here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current DesignPrinciples wiki page to
doc/develop/designprinciples.rst. The changes here are for formatting
or slight rewording so that it reads well when linking to other Sphinx
documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the current CodingStyle wiki page to doc/develop/codingstyle.rst.
The changes here are for formatting or slight rewording so that it reads
well when linking to other Sphinx documents.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MT7621 requires external binary blob being executed during u-boot's
boot-up flow. It's necessary to provide a guide here for users to correctly
build the u-boot.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Our statistics pages have always been generated by gitdm. After
patching gitdm to generate an acceptable Sphinx output for tables,
include that and some other basic formatting here.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Explain why fdt_addr and initrd_addr should not be set to disable
relocation normally.
- Provide some advice on the typical loadaddr default value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This variable is never set nor explained why it would be set, drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This tool seems a bit underloved. Unfortunately, it seems to be missing
support for FIT images. Alas...
Add a man page documenting it. The example is taken from commit a804b5ce2d
("Add dumpimage, a tool to extract data from U-Boot images").
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Despite the original description of these options, they are not always
image names, or even files. Some image types use these options to convey
configuration directly. Re-document these options as configuration options.
Additionally, add a new section documenting the format of the configuration
for each image type which uses it. In general, if configuration is used
directly (without a separate file) I have added documentation for it. If
the configuration points to a separate file, I have referenced that file's
documentation. Where there is no such documentation, I have added it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The mkimage command has had many options added over the years.
Unfortunately, we are starting to run out of short options. Recent options
don't have any obvious relation to their meaning (e.g. -o/-g). Fortunately,
long options exist. Add long options for each current short option.
For the curious, the remaining short options are HIkLmMPQSuUwWXyYzZ.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per man-pages(7), "use of an AUTHORS section is strongly discouraged."
Remove it, and instead add some copyright notices and an SPDX. The default
license for U-Boot is GPL2, so that's what I put. The copyright dates are
based on the commit dates.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a SEE ALSO section to link to similar man pages, as well as to
the U-Boot documentation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In leiu of a non-standard HOMEPAGE section, add a BUGS section with a link
to the issue tracker.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes a variety of changes for the options to make them
typographically consistent, clarify their meaning, and fix grammatical (or
other) errors. Many of the changes here are stylistic, though there are a
few fixes. The main changes I made across the board were:
- All options are bolded and parameters italicised
- All single quotes are properly matched (instead of using apostrophes)
- Minor background info has been added to clarify many underdocumented
options
- Default values for options are documented
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The description in NAME should not be capitalized. Fix a grammatical error
as well.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves some options which work in any mode to the general options
section. -p is moved to after -E/-B since those options are related. This
also adds documentation for -h and -V.
The -F, -l, and -G options are documented twice. Remove the second
documentation in each case. The synopsis for -l also suggests an implied
second uimage-file-name parameter. E.g.
mkimage [-l uimage-file-name] uimage-file-name
This is misleading, so remove it. Wrap a few lines to 80 characters as
well.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The options are divided up into several subsections. Use the appropriate
macro. While we're at it, rename the headings to better reflect the
contents of their sections.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Square brackets are commonly used to denote optional parts of a command.
However, all option arguments are mandatory. Remove these brackets. This
also removes some unnecessary quotation marks, and uses hyphens to connect
words in option arguments. This is intended to just clean up the
formatting, leaving content corrections to later patches.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This puts each example in a new paragraph and uses a hanging indent for
continued lines to increase clarity. We use tabs instead of .in or .RS for
the indent because it renders properly in both man and mandoc (which is
what many common HTML man pages use). The only nit is that the tab stops in
man default to something like 2", so reduce that to 1". We also escape
every "minus" as recommended by man-pages(7).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Blank lines do not have well-defined semantics in fill mode (the default).
Instead, use empty requests (.) where vertical space is necessary for
readability. There are a few places where we use a paragraph instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The synopsis section is a bit messy. As an example, "uimage file name" is
printed in italics, bold, and roman (depending on the line). This cleans
things up and converts the synopsis section to use standard style. The
.SY/.YS macros set up appropriate formatting for command synopsis sections
(such as disabling hyphenation and setting a hanging indent). All parts of
the synopsis now use the following style:
- Bold for parts of the command which should be typed in by the user (such
as the program name and flags)
- Italic for parts which should be replaced (such as uimage-file-name)
- Roman for parts which should not be typed at all (such as brackets)
Multi-word variables now use hyphens to connect their words instead of
spaces. This makes it clearer that all the words are part of the same
variable. Additionally, "option ..." is used to denote where other options
may be specified, as this appears to be standard style.
In addition to the above style changes, this also makes some changes to
content. The use of the term "legacy" has been removed, since this simply
refers to any non-FIT image type. Additionally, wording like "uimage file
name" has been replaced with "image-file-name" to better reflect that
images may or may not be uImages. Lastly, the "auto" value for -f is
documented in the synopsis.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point, the only user of ohci-hcd that also uses PCI is using DM,
so we can drop CONFIG_PCI_OHCI* usage. No platforms set either of
CONFIG_SYS_USB_OHCI_BOARD_INIT or CONFIG_SYS_USB_OHCI_CPU_INIT so those
hooks can be removed as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a preliminary documentation introducing different
boot sequences, and notably the recovery mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220706093649.3261229-1-narmstrong@baylibre.com
Add a comment explaining the design goals of bloblist, to make it easier
for people to understand and comment on the structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cp.b is used a lot as a way to load binaries to memory and execute
them, however we may need to integrate this with the efi subsystem to
set it up as a bootdev.
So, introduce a loadm command that will be consistent with the other
loadX commands and will call the efi API's.
ex: loadm $kernel_addr $kernel_addr_r $kernel_size
with this a kernel with CONFIG_EFI_STUB enabled will be loaded and
then subsequently booted with bootefi command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add in U-Boot documentation the quick instruction to
setup the STMicroelectronics STM32MP13x boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for new compatible "st,stm32mp13-ddr" to manage the
DDR sub system (Controller and PHY) in STM32MP13x SOC:
- only one AXI port
- support of 16 port output (MEMC_DRAM_DATA_WIDTH = 2)
The STM32MP15x SOC have 2 AXI ports and 32 bits support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.
While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).
nvmem devices can specify "cells" in their device tree:
qfprom: eeprom@700000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0x00700000 0x100000>;
/* ... */
tsens_calibration: calib@404 {
reg = <0x404 0x10>;
};
};
which can then be referenced like:
tsens {
/* ... */
nvmem-cells = <&tsens_calibration>;
nvmem-cell-names = "calibration";
};
The tsens driver could then read the calibration value like:
struct nvmem_cell cal_cell;
u8 cal[16];
nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
nvmem_cell_read(&cal_cell, cal, sizeof(cal));
Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.
Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.
The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for signing images in auto-generated FITs. To do this,
we need to add a signature node. The algorithm name property already has
its own option, but we need one for the key name hint. We could have
gone the -G route and added an explicit name for the public key (like
what is done for the private key). However, many places assume the
public key can be constructed from the key dir and hint, and I don't
want to do the refactoring necessary.
As a consequence of this, it is now easier to add public keys to an
existing image without signing something. This could be done all along,
but now you don't have to create an its just to do it. Ideally, we
wouldn't create a FIT at the end. This could be done by calling
fit_image_setup_sig/info.crypto->add_verify_data directly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Document -G and the secondary image types which can be used with -R.
Also reword the documentation of -s for clarity.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The actual support was added in commit fec8c900c8 ("power: regulator:
Add support for regulator-force-boot-off"), update the docs to include
this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
The OsIndications is a 64 bit variable, and the current code expects
the value of the variable to be 64 bit. Update the documentation to
reflect this fact.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
"valu" should be "value".
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The firmware management protocol can be used to manage device firmware.
U-Boot can be configured to provide an implementation.
Document the related functions in the API section.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For indicating the address and size of a memory region other commands use a
<addr>[:<size>] syntax. Do the same for bootefi.
Fixes: 2058983689 ("cmd: bootefi: restore ability to boot arbitrary blob")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This documents some additional options which can be used with valgrind, as
well as directions for future work. It also fixes up inline literals to
actually be inline literals (and not italics). The content of this
documentation is primarily adapted from [1].
[1] https://lore.kernel.org/u-boot/57cb4b49-fa30-1194-9ac3-faa53e8033bd@gmail.com/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The following Python packages are used by U-Boot, too:
* python3-asteval
* python3-subunit
* python3-testtools
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Image created by LTO is not friendly to debugger, let's document this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Mention CONFIG_CC_OPTIMIZE_FOR_DEBUG and LLDB.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It should be CONFIG_SANDBOX_RAM_SIZE_MB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Set kernel_comp_addr_r and kernel_comp_size for compressed kernel.
Adjust existing addresses for ramdisk, so that kernel_comp_addr_r
comes before the ramdisk image, since the decompressed kernel size
is known to us. This way we can allow big ramdisk image to be loaded.
Update unleashed.rst to remove the manual environment configuration
for compressed kernel boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
Over the years, several options have not made it into the help message.
Document them. Do the same for the man page.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
%s/cammand/command/
%s/sequencies/sequences/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an initial VPL build for sandbox. This includes the flow:
TPL (with of-platdata) -> VPL -> SPL -> U-Boot
To run it:
./tpl/u-boot-tpl -D
The -D is needed to get the default device tree, which includes the serial
console info.
Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
The '--args' parameter to gdb comes before the binary that the debugger
will be attached to rather than after the binary and before the
arguments. Fix that in the docs.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
A 'bootdev' is a device which can be used to boot an operating system.
It is a child of the media device (e.g. MMC) which handles reading files
from that device, such as a bootflow file.
Add a uclass for bootdev and the various helpers needed to make it
work. Also add a binding file, empty for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'bootstd' device provides the central information about U-Boot
standard boot.
Add a uclass for bootstd and the various helpers needed to make it
work. Also add a binding file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some basic stuff about tag support is explained under
doc/devlop/driver-model.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A image_size parameter has been added to the bootefi parameter.
Describe all parameters.
Correct how the description of how the device-path in the loaded
image protocol is determined.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Adds simple documentation about common properties for watchdog
in the device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The imx8mn_evk target have been converted to use binman.
With the binman approach the ATF load address is described via
devicetree, so remove the now unneeded instruction of exporting
ATF_LOAD_ADDR.
Signed-off-by: Fabio Estevam <festevam@denx.de>