The PMIC button driver is a much better representation of the hardware
here, adjust the boards to use upstream DT and the PMIC button driver
instead of exposing the buttons as GPIOs and relying on the GPIO-button
driver.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This driver is just a stub, but it's necessary to support the upcoming
reset driver changes.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Clock drivers don't belong here, move them to the right place and
declutter mach-snapdragon a bit.
To de-couple these drivers from specific "target" platforms, add
additional config options to enable each clock driver gated behind a
common CLK_QCOM option and enable them by default for the respective
targets. This will make future work easier as we move towards a generic
Qualcomm target.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Synchronize R-Car R8A779F0 S4 DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77990 E3 DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77970 V3M DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7792 V2H DTs with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
It may be necessary to set breakpoints etc. on a specific fault handler in SPL.
Add a Kconfig option to separate the different handlers into their own individual infinite loops.
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Use device specific naming for functions so as to not overlap
with common function names.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix compilation issue with overlapping lwip and march defines.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a new eDPU revision that uses Marvell 88E6361 switch onboard.
We can rely on detecting the switch to enable and fixup the Linux DTS
so a single DTS can be used.
There is currently no support for the 88E6361 switch and thus no working
networking in U-Boot, so we disable both ports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
The ATF implementation for AC5/AC5X ends up with bl31 living in some
internal SRAM. This is in the middle of the large MMIO region that we
were using. Adjust this to be finer grained blocks based on the address
map from the AC5X Family Control and Management Subsystem Functional
Datasheet.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
- Removed fdt_addr from verdin-imx8mm to fix booting via bootefi.
- Support Ethernet PHY autodection on Data Modul i.MX8M Mini/Plus eDM
SBC
- Add i.MX93 binman support
- Add support for imx93-var-som
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add dedicated Makefile targets for the i.MX93 and a new imx93-u-boot.dtsi
device-tree to create binman images.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add fields for the location of ACPI tables to the global data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation updates for endeavoru, lg_x3, grouper and transformers,
addition of MIPI calibration clock name for T114 (inline with T124+),
conversion of TEGRA_SUPPORT_NON_SECURE into Kconfig and endeavoru
stability improvements.
This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754 ("arm: dts: k3-am654: pull in dtb update from Linux")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Manorit Chawdhry <m-chawdhry@ti.com> says:
K3 devices have firewalls that are used to prevent illegal accesses to
memory regions that are deemed secure. The series prevents the illegal
accesses to ATF and OP-TEE regions that are present in different K3
devices.
AM62X, AM62AX and AM64X are currently in hold due to some firewall
configurations that our System Controller (TIFS) needs to handle.
The devices that are not configured with the firewalling nodes will not
be affected and can continue to work fine until the firewall nodes are
added so will be a non-blocking merge.
Test Logs: https://gist.github.com/manorit2001/4cead2fb3a19eb5d19005b3f54682627
CICD Run: https://github.com/u-boot/u-boot/pull/442
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For readability during configuring firewalls, adding k3-security.h file
and including it in k3-binman.dtsi to be accessible across K3 SoCs
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Principle is exactly the same as on T124, testing of register
which behaves differently in secure and non-secure states.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu secure proxy node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The dummy_clock node is used to help the drivers probe the IO needed to
setup consoles and boot media to load firmware into the SoC.
This dummy_clock isn't a device that exists nor does it exist in the
mcu domain. So move it from cbass_mcu to the root node to avoid any
confusion.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
These aliases are not needed in U-Boot. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we have duplicate
properties in the root node. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate vtt_pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mdio node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The pinmux for usb0 is missing from the Linux board dtb file. Remove it
until we can introduce it in Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate ospi0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate wkup_i2c0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate sdhci1 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
