Relocate cpu_ops pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled.
The (gd->flags & GD_FLG_RELOC) check was added to make sure the reloc_done
logic works for drivers that use DM_FLAG_PRE_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Migrate cpu command to use U_BOOT_CMD_WITH_SUBCMDS() helper macro, to
reduce duplicated code. This also fixes the cpu command on boards that
enable CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Microblaze is using NEEDS_MANUAL_RELOC from the beginnging. This is causing
issues with function pointer arrays which need to be updated manually after
relocation. Building code with -fPIC and linking with -pic will remove this
limitation and there is no longer need to run manual update.
By default still old option is enabled but by disabling NEEDS_MANUAL_RELOC
code will be compiled for full relocation.
The patch does couple of things which are connected to each other.
- Define STATIC_RELA dependency to call relocate-rela to fill sections.
- REMAKE_ELF was already enabled but u-boot file can't be used because
sections are empty. relocate-rela will fill them and output file is
u-boot.elf which should be used.
- Add support for full relocation (u-boot.elf)
- Add support for early relocation when u-boot.bin is loaded to different
address then CONFIG_SYS_TEXT_BASE
- Add rela.dyn and dynsym sections
Disabling NEEDS_MANUAL_RELOC U-Boot size increased by 10% of it's original
size (550kB to 608kB).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a845670b34925859b2e321875f7588a29f6655f9.1655299267.git.michal.simek@amd.com
Microblaze is 32bit that's why it is using elf32 format. Relocation code
requires to get information about rela and dynsym senctions and also text
base which was used for compilation.
Code build with -fPIC and linked with -pic generates 4 relocation types.
R_MICROBLAZE_NONE is the easiest one which doesn't require any action.
R_MICROBLAZE_REL only requires write addend to r_offset address.
R_MICROBLAZE_32/R_MICROBLAZE_GLOB_DAT are the most complicated. There is a
need to find out symbol value with adding symbol value and write it to
address pointed by r_offset. Calculation with addend is also added but
only 0 addend values are generated now.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9912c3d76933bdf75e1ebb6aab43726cd32cafb5.1655299267.git.michal.simek@amd.com
Adding support for new type requires to change code layout that's why move
elf64 code to own function for easier maintenance.
It also solves the problem with not calling fclose in case of error.
Return value from rela_elf64 is saved to variable that's why fclose() is
called all the time.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/21763b80527521c85ca7d4ac64ad6ff4885409c8.1655299267.git.michal.simek@amd.com
Symbol handling depends on compilation flags. Right now manual relocation
is used that's why symbols can be referenced just by name and there is no
need to find them out. But when position independent code (PIC) is used
symbols need to be described differently. That's why having one macro
change is easier than changing the whole code.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d704e9a267c8b536452fb999111dbfbc9d652be5.1655299267.git.michal.simek@amd.com
Right now U-Boot runs all the time from the same address where it is loaded
but going to full relocation code starting address doesn't need to be fixed
and can be simply discovered from reading PC register. That's why use r20
to get PC address and subtract offset from the beginning to get starting
address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/044b727c33dfbe662f68512d0da0775a4805f360.1655299267.git.michal.simek@amd.com
Enable u-boot.elf recreation from u-boot.bin to prepare for removing manul
relocation. Enable option for big endian configuration but it is not used
too much that's why it is completely untested.
By supporting this system there is a need to define LITTLE/BIG endian
Kconfig options to pass -EL/-EB flags.
Full command line for u-boot.elf recreation looks like this:
microblazeel-xilinx-linux-gnu-objcopy -I binary -B microblaze \
-O elf32-microblazeel u-boot.bin u-boot-elf.o
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e242a519fcd1c693b9103c5599b515af555ca43.1655299267.git.michal.simek@amd.com
CONFIG_SYS_INIT_SP_OFFSET macro place stack to TEXT_BASE - SYS_MALLOC_F_LEN
but there is no reason to do it now because board_init_f_alloc_reserve()
returns exact location where stack should be. That's why stack location is
calculated at run time and there is no need to hardcode it via macro. This
change will help with placing U-Boot to any address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e9aee69646e022fd8a96cbee2d2a07ab81fb6e05.1655299267.git.michal.simek@amd.com
When U-Boot starts stack protection can be already enabled that's why setup
the lowest possible SLR value which is address 0. And the highest possible
stack in front of U-Boot. That's why you should never load U-Boot to the
beginning of DDR. There must be some space reserved. Code is using this
location for early malloc space, early global data and stack.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/86b9748bad12142659804d6381bc6bbf20be44f1.1655299267.git.michal.simek@amd.com
There is no need to pass section information via parameters.
Let's read text base and rela start/end directly from elf.
It will help with reading other information from ELF for others
architecture. Input to relocate-rela is u-boot binary and u-boot ELF.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ab7ae14a6e058722e8c608089729e98edf20a08d.1655299267.git.michal.simek@amd.com
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations. DT property output-enable brings out the pins from
tri-state, whereas bias-high-impedance changes the pins state to
tri-state.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1a02cd41d183d397ebce23c497178281c7286692.1655286745.git.michal.simek@amd.com
Do not use 0 as address for memory because of the special meaning for
pointers (null pointer). Change the spl bss start address to the second
page.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220607074314.27125-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Board is using kv260 design for couple of parts defined by spec like i2c
eeproms, ina260, uart, etc.
Board has 4 gems. One gem connected via PS SGMII(GT), another PS RGMII(MIO)
and 2 via EMIO. First two shares the same MIO lines for PHYs. PL based one
have separate EMIO lines via PL.
Also two USB 3.0 with usb hubs are present. USB phys and USB hubs should
have separate reset line. The first usb0 hub also has USB-SD controller
(usb2244) connected to port 0.
To test compatibility with k26 you can run:
fdtoverlay -o /tmp/output.dtb -i arch/arm/dts/zynqmp-sm-k26-revA.dtb \
arch/arm/dts/zynqmp-sck-kr-g-revA.dtbo
Also add support for kr260-revB board. Based on FRU it is revision B
but schematics can be label as revA03.
Changes in revB are:
- SFP light
- GEM2/3 TX_CLK fixes
- PMOD/RPI connector fixes
- Replace si5332 with oscilators
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/dac2ee1826e73b89c8cc1e430354eb43d291f675.1652870941.git.michal.simek@amd.com
Add support to switch to EL1 and load an EL1 app from U-Boot which is
executing at EL2 or EL3 in aarch64 mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220506055345.1921-1-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
CONFIG_DM_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet. Move ethernet
print info statement from plat function to probe function, as phyaddr is
not enumerated when CONFIG_DM_ETH_PHY is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/93e11ccca56b6e52b2dcc283d08d5042537f828f.1652181968.git.michal.simek@amd.com
CONFIG_DM_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet. Move ethernet
print info statement from plat function to probe function, as phyaddr is
not enumerated when CONFIG_DM_ETH_PHY is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/ecfec78234233fefdc172c141c207b2d78ef70c5.1652181968.git.michal.simek@amd.com
This consists of two slightly related series. For the first, to quote
the author:
This series implements 2 features in driver/firmware/scmi.
First, a single change adds support for SCMI OP-TEE transport to
use OP-TEE native shared memory. See the 1st patch in this series:
"firmware: scmi: optee: use TEE shared memory for SCMI messages".
Then come changes for supporting multi-channel in the SCMI drivers.
I've split the implementation in 11 several small incremental changes
in the hope it helps the review. Few minor fixup commits are also
inserted in the series.
And the second series implements some smccc improvements.
To quote the author:
This series introduces ASAN and a basic fuzzing infrastructure that
works with sandbox. The example fuzz test towards the end of the series
will find something pretty quickly. That something is fixed by the
series "virtio: Harden and test vring" that needs to be applied for the
final patch in this series.
There is some refactoring to stop using '.' prefixed sections. ELF
defines sections with names that contain anything that isn't
alphanumeric or an underscore as being for system use which means
clang's ASAN instrumentation happily add redzones between the contained
objects. That's not what we want for things like linker lists where the
linker script has carefully placed the sections contiguously. By
renaming the sections, clang sees them as user sections and doesn't add
instrumentation.
ASAN is left disabled by default as there are still some tests that it
triggers on and will need some more investigation to fix. It can be
enabled with CONFIG_ASAN or passing `-a ASAN` to buildman.
Adds random number generator driver using Arm SMCCC TRNG interface to
get entropy bytes from secure monitor. The driver registers as an
Arm SMCCC feature driver to allow PSCI driver to bind a device for
when secure monitor exposes RNG support from Arm SMCCC TRNG interface.
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Use PSCI device to query Arm SMCCC v1.1 support from secure monitor
and if so, bind drivers for the SMCCC features that monitor supports.
Drivers willing to be bound from Arm SMCCC features discovery can use
macro ARM_SMCCC_FEATURE_DRIVER() to register to smccc feature discovery,
providing target driver name and a callback function that returns
whether or not the SMCCC feature is supported by the system.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Defines function IDs ARM_SMCCC_ARCH_FEATURES used to query SMCCC feature
support, applicable from Arm SMCCC v1.1 specification.
Defines macro ARM_SMCCC_RET_NOT_SUPPORTED as generic return identifier
for when a SMCCC feature is not supported.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Updates .process_msg operators of the SCMI transport drivers that
supports multi-channel to use it now that drivers do provide
the reference through channel argument. These are the mailbox
agent, the optee agent and the smccc agent.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Update SCMI regulator controller driver to get its assigned SCMI channel
during initialization. This change allows SCMI voltage domain protocol
to use a dedicated channel when defined in the DT. The reference is
saved in SCMI regulator controller driver private data.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Update SCMI reset controller driver to get its assigned SCMI channel
during initialization. This change allows SCMI reset domain protocol
to use a dedicated channel when defined in the DT. The reference is
saved in SCMI reset controller driver private data.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Update SCMI clock driver to get its assigned SCMI channel during
initialization. This change allows SCMI clock protocol to use a
dedicated channel when defined in the DT. The reference is saved
in SCMI clock driver private data.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
