Update MTD partitions of Kria device trees to allocate 128KB of QSPI
memory for secure OS. Increased "SHA256" partition size & changed
starting address of "User" partition to accommodate the new partition
"Secure OS Storage"
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9cc64b8c731d11439de73d0af54c65080068f00b.1661242681.git.michal.simek@amd.com
BTN_MISC looks like the most reasonable option for this button.
Button is used by firmware to indicate (after reset, power up) that user
wants to do firmware upgrade via firmware update utility.
For bootloader or OS is this just user button which is worth to have it
mapped.
Also button can be used as a wakeup source and pressing it for more time
can generate more chars that's why also adding wakeup-source and autorepeat
properties.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/7f6d627473632c3c3036ec9f6aaa36e00f4615e2.1652262769.git.michal.simek@amd.com
In all the ZynqMP boards dts files tx-buswidth is by default set to 1. Due
to this the framework only issues 1-1-1 write commands to the GQSPI driver.
But the GQSPI controller is capable of handling 1-4-4 write commands, so
updated the tx-buswidth to 4 in ZynqMP boards dts files. This would enable
the spi-nor framework to issue 1-4-4 write commands instead of 1-1-1. This
will increase the tx data transfer rate, as now the tx data will be
transferred on four lines instead on single line.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ad61199f55e5e00f29de6206d9d1872a52a7657e.1652193179.git.michal.simek@amd.com
The main reason is to send pmufw cfg overlay from U-Boot to PMUFW to enable
access to DP. Overlay is sent when cls command is called and for that IP
has to be enabled in carrier cards.
And IP needs to be also enabled in SOM dt because with DTB reselection new
DT is not parsed in pre reloc U-Boot instance. It is called from board_f
via embedded_dtb_select(). That's why bind function is not able to allocate
memory and it ends up with error:
"Video device 'display@fd4a0000' cannot allocate frame buffer memory
-ensure the device is set up before relocation"
To avoid this situation DP is placed also to SOM where bind function is
called and frame buffer memory is allocated and just reused after DTB
reselection. Result is the same. There could be a problem in Linux with
different DP configurations but that's need to be solved there because
console should be on from u-boot already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c4f31641f917fddb09d976f56875057c658f264c.1645629459.git.michal.simek@xilinx.com
With limited low level configuration done via psu-init only IPs connected
on SOM are initialized and configured. All IPs connected to carrier card
are not initialized. There is a need to do proper reset, pin configuration
and also clock setting.
The patch targets the last part which is setting up proper clock for USBs
and SDs.
Also setup proper bus width for SD cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/d9f80b2551bd246c3d7ecb09b516806c8dc83ed9.1645629459.git.michal.simek@xilinx.com
U-Boot support board detection at run time and based on it change DT.
This feature is implemented for SOM Kria platforms which contain two
eeproms which contain information about SOM module and CC (Carrier card).
Full U-Boot starts with minimal DT file defined by
CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image.
It is using default setup of board_name variable initializaed to
DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option.
When DTB_RESELECT is enabled board_detection() is called. Keep it your mind
that this code is called before relocation. board_detection() is calling
xilinx_read_eeprom() which fills board_info (xilinx_board_description)
structure which are parsed in board_name_decode().
Based on DT configuration and amount of nvmemX aliases name of the board is
composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev"
<board_revision> "-" <cc_name> "-rev" <cc_revision>.
If CC is not present or more are available it keeps going.
When board name is composed and returned from board_name_decode() it is
assigned to board_name variable which is used by
board_fit_config_name_match() which is called via fdtdec_setup() when it
goes over config options in multi dtb FIT image.
From practical point of view multi DTB image is key point here which has to
contain configs for detected combinations. Unfortunately as of now they
have to be full DTBs and DTBOs are not supported.
That's why configuration like:
config_X {
description = "zynqmp-board-cc";
fdt = "board", "cc";
};
needs to be squashed together with:
fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \
arch/arm/dts/zynqmp-cc.dtbo
and only one dtb is in fit:
config_X {
description = "zynqmp-board-cc";
fdt = "board-cc";
};
For creating multi DTBs fit image use mkimage -E, e.g.:
mkimage -E -f all.its all.dtb
When DTB_RESELECT is enabled xilinx_read_eeprom() is called before
relocation and it uses calloc for getting a buffer. Because this is dynamic
memory it is not relocated that's why xilinx_read_eeprom() is called again
as the part of board_init(). This second read with calloc buffer placed in
proper position board_late_init_xilinx() can setup u-boot variables as
before.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT files have been added this year but forgot to update it that's why do it
in separate patch now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch contains several DT files for SOM platform.
Carrier card is sck-kv (KV260) revA/B. SMK-K26 is description for starter
kit which doesn't have EMMC populated. And SM-K26 is full som with EMMC.
Files are divided in this way to make sure that SOM can be plugged to
different carrier card and all peripherals on SOM (or defined by a spec) can
be used by U-Boot. Full DT for SOM+CC can be merged together as overlays.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
