This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family. Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixed wrong SH7720 CPU macro and changed macro that
calculated value of SCBRR register.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move the initialization of the LAWs into C code and provide an API
to allow modification of LAWs after init.
Board code is responsible to provide a law_table and num_law_entries.
We should be able to use the same code on 86xx as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
rx_status on the memory is basically in LE, but needs to be handled in CPU
endian. le32_to_cpu() takes up this mission. Even if on the sane hardware,
it'll work fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Current driver is meant for cache coherent systems. This patch adds
flush_cache() routines to support cache non-coherent systems.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
"to = (currticks() + RTL_TIMEOUT)" has possibilities to wrap around. If it
does, the condition "(currticks() < to)" becomes invalid and immediately
leads to tx timeout error. This patch introduces the fine-graded udely(10)
loops to ease the impact of wrapping around.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add the support of RealTek RTL8211B PHY, the RTL8211B
PHY only supports RGMII and MII mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
PHY less board prints out lots of "read wrong ...":
read wrong value : mii_id 3,mii_reg 2, base e0102320
read wrong value : mii_id 3,mii_reg 3, base e0102320
UEC: PHY is Generic MII (ffffffff)
read wrong value : mii_id 3,mii_reg 4, base e0102320
read wrong value : mii_id 3,mii_reg 0, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
FSL UEC0: Full Duplex
FSL UEC0: Speed 100BT
FSL UEC0: Link is up
Using FSL UEC0 device
Make this printout depend on UEC_VERBOSE_DEBUG and
remove its definition in uec_phy.c
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
actually polling for PHY autonegotiation to finish enables us to remove the
5 second boot prompt latency present on QE based boards.
call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from
uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait
code shamelessly stolen from tsec driver.
also rm unused CONFIG_RMII_MODE code.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current TSEC driver limits MDIO access to the devices that have been configured as attached
to a TSEC MAC. This patch allows access to any PHY device on the MDIO bus through the 'mii' commands.
Signed-off-by: Michael Firth <michael.firth@bt.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch extends the number of supported UECs to 4. Note that the
problem of QE thread resources exhaustion is resolved by setting the
correct number of QE threads according to Ethernet type (GBE or FE).
Signed-off-by: David Saada <david.saada@ecitele.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SH7710/SH7712 of SH3 CPU are supported.
SH771X is called SH-Ether, and has the Ether controller in CPU.
The driver of Ether is not included in this patch.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
qe.c: In function 'qe_upload_firmware':
qe.c:390: warning: pointer targets in passing argument 2
uec.c: In function 'uec_initialize':
uec.c:1236: warning: 'uec_info' may be used uninitialized
Signed-off-by: Dave Liu <daveliu@freescale.com>
Lines of the lenght CONSOLE_COLS or greater than CONSOLE_COLS
are not displayed correctly. This is an attempt to fix
this issue. Also add carriage return handling.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Change return values of init() functions in all Ethernet drivers to conform
to the following:
>=0: Success
<0: Failure
All drivers going forward should return 0 on success. Current drivers that
return 1 on success were left as-is to minimize changes.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob and
perform the actual upload. Add command-line command "qe fw" to take a firmware
blob in memory and upload it. Update ft_cpu_setup() on 85xx to create the
'firmware' device tree node if U-Boot has uploaded a firmware. Fully define
'struct rsp' in immap_qe.h to include the actual RISC Special Registers.
Signed-off-by: Timur Tabi <timur@freescale.com>
It is unclear on what platforms this driver has been tested, since
noone up to now defines CONFIG_RTL8169 in the board configuration
header. Now it has been fixed for a big-endian mpc8241 based
linkstation platform. This patch presents the necessary endianness
conversion fixes.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: Stefan Roese <sr@denx.de>
This driver is based on the driver for the M41T11. In the intended
application, the RTC will be powered by a large capacitor, rather than a
battery. The driver therefore checks to see whether the RTC has lost
power. The chip's OUT bit is normally reset from its power-up state. If
the OUT bit is read as set, or if the date and time are not valid, then the
RTC is assumed to have lost power, and its date and time are reset to
1900-01-01 00:00:00.
Support for adjusting the speed of the clock to improve accuracy is
provided through an environment variable.
Signed-off-by: Larry Johnson <lrj@acm.org>
