Commit graph

23 commits

Author SHA1 Message Date
Masahiro Yamada
b8909976ed ARM: uniphier: update DRAM init code for LD20 SoC (3rd)
- Constify UMC setting data arrays
  - Merge data arrays *_d0 and *_d1.
  - Add PHY parameters for LD20 C1 board

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-29 17:24:26 +09:00
Masahiro Yamada
da0d4d1380 ARM: uniphier: remove unused board attribute macros
After SoC evaluation, they turned out unnecessary.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-29 17:01:40 +09:00
Masahiro Yamada
c72f4d4c2e ARM: uniphier: add PLL init code for LD11 SoC
- Initialize PLLs (SPL initializes only DPLL to save the precious
   SPL memory footprint)
 - Adjust CPLL/MPLL to the final tape-out frequency
 - Set the Cortex-A53 clock to the maximum frequency since it is
   running at 500MHz (SPLL/4) on startup

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-23 01:00:23 +09:00
Masahiro Yamada
682e09ff9f ARM: uniphier: add PLL init code for LD20 SoC
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper.  Split the common code into pll-base-ld20.c for easier
re-use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:12:26 +09:00
Masahiro Yamada
6a3e4274e4 ARM: uniphier: move PLL init code to U-Boot proper where possible
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper.  Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:06:44 +09:00
Masahiro Yamada
b78ffc53c5 ARM: uniphier: move XIRQ pin-mux settings of LD11/LD20
This is the last code in the mach-uniphier/pinctrl/ directory.
Push the remaining code out to delete the directory entirely.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:47:27 +09:00
Masahiro Yamada
68557ec37e ARM: uniphier: consolidate System Bus pin-mux settings for LD11/LD20
Use the pin-mux data in the pinctrl drivers by directly calling
pinctrl_generic_set_state().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:47:18 +09:00
Masahiro Yamada
5ac9dfbe9d ARM: uniphier: consolidate NAND pin-mux settings
The NAND subsystem has not supported the Driver Model yet, but the
NAND pin-mux data are already in the pinctrl drivers.  Use them by
calling pinctrl_generic_set_state() directly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:44 +09:00
Masahiro Yamada
6a93478b93 ARM: uniphier: remove ad-hoc pin-mux code for sLD3
These settings are nicely cared by the pinctrl driver now.  Remove.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:37 +09:00
Masahiro Yamada
f6bbec3d5c ARM: uniphier: introduce flags to adjust DRAM timing for LD20/LD21
Unfortunately, this SoC needs per-board adjustment between clock
and address/command lines.  This flag will be passed to the DRAM
init function and used for compensating the difference of DRAM
timing parameters.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-17 01:29:44 +09:00
Masahiro Yamada
b291671232 ARM: uniphier: merge board init functions into board_init()
Currently, the UniPhier platform calls several init functions in the
following order:

  [1] spl_board_init()
  [2] board_early_init_f()
  [3] board_init()
  [4] board_early_init_r()
  [5] board_late_init()

The serial console is not ready at the point of [2], so we want to
avoid using [2] from the view point of debuggability.  Fortunately,
all of the initialization in [2] can be delayed until [3].  I see no
good reason to split into [3] and [4].  So, merge [2] through [4].

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14 22:54:20 +09:00
Masahiro Yamada
be44a4679f ARM: uniphier: add PH1-LD21 board data
This has the same silicon die as PH1-LD20, but includes DRAM chips
in its package.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24 00:24:58 +09:00
Masahiro Yamada
a74c28a0f2 ARM: uniphier: introduce flags to uniphier_board_data structure
I need to add more board attributes, so the "flags" member will be
handier than separate boolean ones.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-24 00:24:55 +09:00
Masahiro Yamada
667dbcd01d ARM: uniphier: add PH1-LD11 SoC support
This is a low-cost ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-26 00:37:13 +09:00
Masahiro Yamada
bef4b024e9 ARM: uniphier: move pin-mux code into pin_init function
The code in uniphier_sld3_sbc_init() is pin-muxing, so it would
be a better fit in uniphier_sld3_early_pin_init().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-01 01:13:45 +09:00
Masahiro Yamada
5eb4150e84 ARM: uniphier: allow to use System Bus for ROM boot mode of PH1-LD20
The System Bus is not available by default on the ROM boot mode of
PH1-LD20.  To use devices connected to the System Bus, such as the
Micro Support Card, it is necessary to set up pin-muxing and some
System Bus Controller register.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-01 01:09:18 +09:00
Masahiro Yamada
9d0c2ceb35 ARM: uniphier: add PH1-LD20 SoC support
This is the first ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:54:08 +09:00
Masahiro Yamada
5b66006646 ARM: uniphier: rename function names ph1_* to uniphier_*
Eliminate the "ph1"_ prefixes from function names because "uniphier_"
describes the SoC familiy better.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:59:47 +09:00
Masahiro Yamada
5d0607c58c ARM: uniphier: refactor SBC init code
There is a bunch of duplication in the System Bus Controller init
code.  Roughly, there are two types in the SBC mode:  Adress/Data
Multiplex Mode and Save Pins Mode.  Consolidate per-SoC functions
into the two, plus per-SoC optional init code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:45:18 +09:00
Masahiro Yamada
4021b4381d ARM: uniphier: add a field to specify DDR3+
Add a field to distinguish DDR3+ from (standard) DDR3.  It also
allows to delete CONFIG_DDR_STANDARD (this is not a software
configuration, but a board attribute).

Default DDR3 spec for each SoC:

  PH1-LD4, PH1-sLD8: DDR3+
  Others: DDR3

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:16 +09:00
Masahiro Yamada
46abfcc99e ARM: uniphier: rework struct uniphier_board_data
This commit reworks "struct uniphier_board_data" with an array of
DRAM channel data in it.  It will allow further cleanups by means of
"for" statements that iterate over the DDR channels.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:16 +09:00
Masahiro Yamada
15607d0d94 ARM: uniphier: add DRAM init code for ProXstream2/PH1-LD6b
As mentioned in the log of commit 019df879a9 (ARM: uniphier: add
ProXstream2 and PH1-LD6b support), the DRAM init code was missing
for a long time.  Finally, here it is.  SPL works now.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13 01:54:55 +09:00
Masahiro Yamada
107b3fb484 ARM: uniphier: move headers out of include/mach directory
These headers are only included locally in arch/arm/mach-uniphier/.
There is no reason to export them by putting in the mach/ directory.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13 01:54:53 +09:00
Renamed from arch/arm/mach-uniphier/include/mach/init.h (Browse further)