Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Following commit 61bd2f75, exclude unused DDR controller from
calculating RAM size for SPL boot.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.
Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
This should make it clear that this symbol is meant to be defined by
board headers.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If MV_DEBUG_WL is defined, DEBUG_WL_S and DEBUG_WL_D macros are missing.
In addition to that, get rid of debug output printing non-existent
counter variable.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
gcc 5.1 generates this new warning (for Armada 38x platforms):
drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result':
drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array
function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument]
memcpy(result, training_result, sizeof(result));
^
drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here
u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM])
^
Since this functions is not referenced anywhere, lets just remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.
Signed-off-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
SAR1_CPU_CORE_MASK was wrong, probably copy/paste
from another architecture.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:
1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is tested on the DB-MV784MP-GP eval board. To really enable ECC
support on this board the I2C EEPROM needs to get changed. As it
saves the enabling of ECC support internally. For this the following
commands can be used to enable ECC support on this board:
Its recommended for first save (print) the value(s) in this EEPROM
address:
=> i2c md 4e 0.1 2
0000: 05 00 ..
To enable ECC support you need to set bit 1 in the 2nd byte:
Marvell>> i2c mw 4e 1.1 02
Marvell>> i2c md 4e 0.1 2
0000: 05 02 ..
To disable ECC support again, please use this command:
Marvell>> i2c mw 4e 1.1 00
Marvell>> i2c md 4e 0.1 2
0000: 05 00 ..
On other AXP boards, simply plugging an ECC DIMM should be enough to
enable ECC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Move the files generated by QTS into the board directory, they should not
be part of the driver files at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up so that it's obvious what it is doing,
fix the formating strings in debug outputs, add kerneldoc.
Make the function return proper errno-compliant return values
and propagate this change throughout sdram.c
Signed-off-by: Marek Vasut <marex@denx.de>
