This patch fixes this clk issue on I2C on imx8qm
=> i2c bus
Bus 3: i2c@5a830000
=> i2c dev 3
Setting bus to 3
Failed to enable ipg clk
Failure changing bus number (-524)
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The Kontron SMARC-sAL28 board uses that flash.
This is the same change as in the linux commit f3418718c0ec ("mtd:
spi-nor: Add support for w25q32jwm").
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Leo Krueger <leo.krueger@zal.aero>
timeout should be in "millisecond" instead of second,
so divided it by 1000 when calculate the load value.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
The test should be checking whether $flags are non-zero and $drv_flags
contain specific flags, however these two sets of flags are separate,
and the two tests should be logically ANDed, not bitwise ANDed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 6900797678 ("cros_ec: Support keyboard scanning with
EC_CMD_GET_NEXT_EVENT") the cros-ec-keyb driver has started using this
command, but the sandbox EC emulator does not recognize it and
continuously prints:
** Unknown EC command 0x67
This patch makes the sandbox driver send basic responses to the command,
but the response only supports keyboard scans for now.
The EC side of this command stores and returns events from a queue, and
returns -EC_RES_UNAVAILABLE when there are no new events. This should be
possible to implement by hooking into the SDL event queue (perhaps via
sandbox_sdl_poll_events). Implementing that is a bit harder to do since
the existing sandbox code is discarding pending keyboard events, then
reading the current keyboard state.
Since the EC emulator never explicitly fails to work on this command,
the fallback to the older command will not trigger and will not be
tested anymore.
Fixes: 6900797678 ("cros_ec: Support keyboard scanning with EC_CMD_GET_NEXT_EVENT")
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Don't use "platdata_auto_alloc_size" but "priv_auto_alloc_size" instead
to auto allocate the private data struct, which is referenced via
dev_get_priv() in this driver. This fixes an ugly bug detected while
trying to boot via SPI NOR.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add support for the OpenCores I2C controller IP core
(See http://www.opencores.org/projects.cgi/web/i2c/overview).
This driver implementation is inspired from the Linux OpenCores
I2C driver available.
Thanks to Peter Korsgaard <peter@korsgaard.com> for writing Linux
OpenCores I2C driver.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
At present if CONFIG_RESET is not enabled, this code shows a warning:
designware_i2c_ofdata_to_platdata() i2c_designware_pci i2c2@16,0:
Can't get reset: -524
Avoid this by checking if reset is supported, first.
Fixes: 622597dee4 ("i2c: designware: add reset ctrl to driver")
Signed-off-by: Simon Glass <sjg@chromium.org>
The hidden I2C slave is also present on the Armada 8k AP806. Testing
shows that this I2C slave causes the same issues as Armada 38x.
Disabling that I2C slave fixes all these issues.
I2C blocks on the Armada 8k CP110 are not affected.
Extend the I2C slave disable to Armada 8k as well.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Regulator can be set to "always-on".
It's not error about enable/disable. It needs to check about
its condition.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
It's useful to know an error number when it's debugging.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
In previous commit to support eMMC HS400,
db8f936 mmc: fsl_esdhc: support eMMC HS400 mode
the steps to configure DLL could be found in commit message,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
these would be fixed as,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us,
then write DLLCFG0[DLL_RESET]
14. Wait for delay chain to lock.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Fixes: db8f93672b ("mmc: fsl_esdhc: support eMMC HS400 mode")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The initial clock setting should be through sysctl register only,
while the mmc_set_clock() will call mmc_set_ios() introduce other
configurations like bus width, mode, and so on.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All of the existing quirks add retries to various calls of mmc_send_cmd.
mmc_send_cmd_quirks is a helper function to do this retrying behavior. It
checks if quirks mode is enabled, and if a specific quirk is activated it
retries on error.
This also adds mmc_send_cmd_retry, which retries on error every time
(instead of if a quirk is activated).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update pin name to avoid duplicated name with SOC GPIO
gpio0...gpio15 / agpio0....agpio7: add a stmfx prefix.
This pin name can be used in pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The device name is used in pinmux command and in log trace
so it is better to use the parent parent name ("stmfx@42" for
example) than a generic name ("pinctrl" or "stmfx-gpio")
to identify the device instance.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the bias configuration for all the GPIO configurations and not
only for input GPIO, as indicated in Reference manual
(Table 81. Port bit configuration table).
Fixes: 43efbb6a3e ("gpio: stm32: add ops get_dir_flags")
Fixes: f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Display the bias information for input gpios or AF configuration,
and not only for output pin, as described in Reference manual
(Table 81. Port bit configuration table).
Fixes: da7a0bb1f2 ("pinctrl: stm32: add information on pin configuration")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The coprocessor is running as soon as the hold boot is de-asserted.
So indicate this running state and save the resource table even
if the protective assert, to avoid autonomous reboot, is failed.
This error case should never occurs.
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the reset function to handle the hold boot bit in RCC
with device tree handle with MCU_HOLD_BOOT identifier.
This generic reset allows to remove the two specific properties:
- st,syscfg-holdboot
- st,syscfg-tz
This patch prepares alignment with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Handle the register RCC_MP_GCR without SET/CLR registers
but with a direct access to bit BOOT_MCU:
- deassert => set the bit: The MCU will not be in HOLD_BOOT
- assert => clear the bit: The MCU will be set in HOLD_BOOT
With this patch the RCC driver handles the MCU_HOLD_BOOT_R value
added in binding stm32mp1-resets.h
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If CONFIG_PHY is not enabled then the dwc3_setup_phy()
returns ENOTSUPP which can be still valid and intentional
so modify error check to handle this -ENOTSUPP.
The same error handling exists in drivers/usb/host/xhci-dwc3.c already
added by commit d648a50c0a ("dwc3: move phy operation to core.c").
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On some board, the ID pin is not connected so the B session must be
overridden with "u-boot,force_b_session_valid" but the VBus sensing
must continue to be handle.
To managed it, this patch adds a new DT field
"u-boot,force-vbus-detection" to use with "u-boot,force_b_session_valid"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Drop unused members from struct sh_pfc_pinctrl.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
This driver supports both RZ/G2H and R-Car H3 SoCs.
Optimize pinctrl image size for RZ/G2H, when support for R-Car H3
(R8A7795) is not enabled
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
This driver supports both RZ/G2N and R-Car M3-N SoCs.
Optimize pinctrl image size for RZ/G2N, when support for R-Car M3-N
(R8A77965) is not enabled.
Based on the simialr patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
This driver supports both RZ/G2M and R-Car M3-W/W+ SoCs.
Optimize pinctrl image size for RZ/G2M, when support for R-Car M3-W/W+
(R8A7796[01]) is not enabled.
Based on the similar patch on Linux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Renesas RZ/G2H (r8a774e1) is pin compatible with R-Car H3 (r8a77951),
however it doesn't have several automotive specific peripherals. Add
a r8a77951 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77951 and r8a774e1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The parameter check for UEFI service GetNextVariableName() is corrected.
The dependencies of CONFIG_DFU_TFTP are simplified.
The set of supported hash algorithms reported by the EFI_TCG2_PROTOCOL is
corrected.
-----BEGIN PGP SIGNATURE-----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=6U7u
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3 (2)
The parameter check for UEFI service GetNextVariableName() is corrected.
The dependencies of CONFIG_DFU_TFTP are simplified.
The set of supported hash algorithms reported by the EFI_TCG2_PROTOCOL is
corrected.
Since CONFIG_UPDATE_COMMON always selects CONFIG_DFU_WRITE_ALT, we can
drop the latter from dependencies of CONFIG_DFU_TFTP.
Fixes: 3149e524fc ("common: update: add a generic interface for FIT
image")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There is no need for GD to be used and priv variable is unused.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change sets the output (hardware) polarity register instead of the
input (software) polarity register for the bcm6858 LED controller. The
logic was inverted (a LED configued active high behaved as active low).
Signed-off-by: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This renames power domains to match the names on the k210 datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
I2C and SCCB previously shared defaults. However, SCCB needs OE_INV and
IE_INV set, but I2C cannot have those bits set. This adds a separate
default for SCCB.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
The reference design of Allwinner V3 series uses an
AXP203 or AXP209 PMIC attached to the I2C0 bus of the SoC, although the
first community-available V3s board, Lichee Pi Zero, omitted it.
Allow to introduce support for the PMIC on boards with it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A new compatible string is introduced for V3 CCU, because it has a few
extra features available.
Add the compatible string to the clock driver. As the extra features are
not touched, just share the description struct now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A new compatible string is introduced for V3 GPIO, because it has more
pins available than V3s.
Add the compatible string to the GPIO driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Fix USB support for rk3399 Pinebook Pro;
- Fix SPI boot for rk3399 boards other than Bob;
- Fix 32bit boards firmware build without SPL_OPTEE support;
- Fix rockchip display driver license;
onenand_probe() function is missing to set mtd->type. So set same type as
which sets onenand Linux kernel driver.
After this change 'mtd list' prints correct type instead of 'Unknown'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Function twl4030_i2c_read() is like twl4030_i2c_read_u8() but instead of
single value it rather returns array of values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
