Commit graph

1101 commits

Author SHA1 Message Date
Marek Vasut
4a03cf38d8 arm64: imx8mp: Inhibit DTC warning on DH i.MX8MP DHCOM rev.100 DTO
Inhibit DTC warning in imx8mp-dhcom-pdk3-overlay-rev100.dts:
"
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (reg_format): /fragment@0/__overlay__:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #address-cells value
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #size-cells value
"

The DTO overwrites the 'reg' property of an ethernet PHY and is only
used on specific combination of old prototype SoM and old prototype
PDK3 carrier board, which had incorrectly placed pull resistor, which
made the PHY change its MDIO address in that specific combination and
which is already fixed on production hardware.

The DTO is implemented in this simple manner because if it contained a
full MDIO bus node reference to define #address-cells and #size-cells,
it would also require a full new copy of the PHY node, i.e.
ethernet-phy@5 { ... reg = <5>; ... }, to avoid DTC warnings about
mismatch between node unit and reg value. The node unit in SoM DT is
ethernet-phy@7 { ... }; .

This simpler approach avoids unnecessary duplication without adverse
side effects.

Reported-by: Fabio Estevam <festevam@denx.de>
Reported-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2023-12-14 15:29:08 -03:00
Andre Przywara
d2e1cc69a2 sunxi: H616: Add OrangePi Zero 3 board support
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.

Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.

The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
2023-12-06 23:09:17 +00:00
Ludwig Kormann
1f6c98c2d3 arm: dts: icnova-a20-adb4006: Add board support
Add board support for ICnova A20 SomPi compute module on
ICnova ADB4006 development board.

Specification:
SoM
- Processor: Allwinner A20 Cortex-A7 Dual Core at 1GHz
- 512MB DDR3 RAM
- Fast Ethernet (Phy: Realtek RTL8201CP)
ADB4006
- I2C
- 2x USB 2.0
- 1x Fast Ethernet port
- 1x SATA
- 2x buttons (PWRON, Boot)
- 2x LEDS
- serial console
- HDMI
- µSD-Card slot
- Audio Line-In / Line-Out
- GPIO pinheaders

https://wiki.in-circuit.de/index.php5?title=ICnova_ADB4006
https://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM

devicetree upstreamed with linux 6.5

Signed-off-by: Ludwig Kormann <ludwig.kormann@ict42.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2023-11-12 16:47:00 +00:00
Tom Fitzhenry
6761cb5bc2 board: rockchip: add Pine64 QuartzPro64 RK3588 board
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.

UART and boot over SD/eMMC/RJ45 are tested to work.

Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")

Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
2023-11-09 11:19:05 +08:00
Michal Simek
7faa6b9069 arm64: versal-net: Add DTSes for mini qspi/ospi configuration
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a99a8d72201a782fc811715942dea97fb5ab583b.1698329087.git.michal.simek@amd.com
2023-11-07 13:47:09 +01:00
Michal Simek
0274447bae arm64: versal: Add DTSes for mini qspi/ospi configuration
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9518ab1c4299a45e800b8611172edd78c9243132.1698329087.git.michal.simek@amd.com
2023-11-07 13:47:09 +01:00
Michal Simek
a787618057 ARM: zynq: Add DTSes for mini qspi configurations
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7d31a9d9c4a76e171eefc619f31fabd0831a614.1698329087.git.michal.simek@amd.com
2023-11-07 13:47:09 +01:00
Michal Simek
da10dd10e0 ARM: zynq: Add DTSes for mini qspi configurations
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/28b3cdd7e91b2b4c3c36d0bf65aa5bac042f248c.1698329087.git.michal.simek@amd.com
2023-11-07 13:47:09 +01:00
Marek Behún
94c0f0b177 arm: mvebu: turris_mox: Extend to support RIPE Atlas Probe
Extend Turris Mox board code to support CZ.NIC's RIPE Atlas Probe.

Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2023-10-26 14:49:36 +02:00
Tom Rini
5cab3515f8 Merge tag 'u-boot-rockchip-20231024' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus;
- clk driver fix for rk3568 and rk3588;
- rkmtd cmd support for rockchip nand device;
- dts update and sync from linux;
2023-10-24 09:39:52 -04:00
Jonas Karlman
b51cf8bb09 board: rockchip: Add Xunlong Orange Pi 5 Plus
Xunlong Orange Pi 5 Plus is a single-board computer based on the
Rockchip RK3588 SoC. The board provides abundant interfaces, including
two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports,
M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C.

Features tested on a Orange Pi 5 Plus 4GB v1.2:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet

Device tree is imported from linux v6.7-rockchip-dts64-1 tag.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-10-24 15:55:16 +08:00
Jonas Karlman
28c5f941ed board: rockchip: Add Xunlong Orange Pi 5
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip
RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO
interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0,
etc.

Features tested on a Orange Pi 5 4GB v1.2:
- SD-card boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet

Device tree is imported from linux v6.7-rockchip-dts64-1 tag.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-10-24 15:55:16 +08:00
Tom Rini
cedc741231 Second set of u-boot-at91 features for the 2024.01 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmU2fxwcHGV1Z2VuLmhy
 aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyKr+B/42+WkPiAiwt79R6Kh5
 UKo404oN1na28D3V12EvikiCH2QWubi38EV7VfcB3jqEpxj4j+rY0cSLZv+u7d4/
 bfQN3FPrcTwYnXYLbYkUKC+MAVzGLiVzFBBhIt5cPrT4iVXctwYY6LJ58aX8uRo6
 KU6CwXYc3cnmIUqpXE4EYbbQU4TAp55SV2n8QLFFI9DHcy2kELfdrZduFn+Hm9Ij
 9sQHH5JxbrGHv5XpcjJkARW3M4K3K4TPzweFGN61VMJwWqzD3L4YPshwIGDfhRui
 LECKCdr/rWkavumXCfw2pD3RYFTqnqnUzaEN/3ueL9FCJ2uFH1EyaoSuXFEn3+Ul
 m1LE
 =CMMd
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-at91-2024.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91

Second set of u-boot-at91 features for the 2024.01 cycle

This feature set a new board named Conclusive KSTR sama5d27 with some
small prerequisites patches.
2023-10-23 11:39:38 -04:00
Artur Rojek
27347893f0 board: Add support for Conclusive KSTR-SAMA5D27
Introduce support for Conclusive KSTR-SAMA5D27 Single Board Computer.

Co-developed-by: Jakub Klama <jakub@conclusive.pl>
Signed-off-by: Jakub Klama <jakub@conclusive.pl>
Co-developed-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Artur Rojek <artur@conclusive.pl>
2023-10-23 17:07:06 +03:00
John Clark
b0b8086898 board: rockchip: add FriendlyElec NanoPC-T6 rk3588 board
The NanoPC-T6 is a Rockchip RK3588 based SBC by FriendlyElec.

There are four variants depending on the DRAM size: 4G/32GB eMMC,
8G/64GB eMMC, 16G/16MB SPI NOR, and 16G/256GB eMMC/16MB SPI NOR

Specifications:
    CPU: Rockchip RK3588, 4x Cortex-A76 (up to 2.4GHz)
                        + 4x Cortex-A55 (up to 1.8GHz)
    GPU: Mali-G610 MP4
    VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder,
         4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
    NPU: 6TOPs, supports INT4/INT8/INT16/FP16
    RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
    eMMC: 0GB/32GB/64GB/256GB HS400
    MicroSD Slot: MicroSD SDR104
    PCIe 3.0: M.2 M-Key x1, PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s
    Ethernet: PCIe 2.5G 2x Ethernet (RTL8125BG)
    PCIe 2.1: M.2 E-Key x1, PCIe 2.1 x1 and USB2.0 Host,
              supports M.2 WiFi and Bluetooth
    4G Module: MiniPCIe x1, MicroSIM Card Slot x1
    Audio Out: 3.5mm jack for stereo headphone output
    Audio In: 2.0mm PH-2A connector for analog microphone input
    Video Input: standard HDMI input port, up to 4Kp60
    2x 4-lane MIPI-CSI, compatible with MIPI V1.2
    Video Output: 2x standard HDMI output ports compatible with HDMI2.1,
                  HDMI2.0, and HDMI1.4
    2x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
    USB-A: USB 3.0, Type A
    USB-C: Full function USB Type‑C port, DP display up to 4Kp60, USB 3.0
    40-pin 2.54mm header connector: up to 2x SPIs, 6x UARTs, 1x I2Cs,
                                    8x PWMs, 2x I2Ss, 28x GPIOs
    Debug UART: 3 Pin 2.54mm header, 3V level, 1500000bps
    Onboard IR receiver: 38KHz carrier frequency
    RTC Battery: 2 Pin 1.27/1.25mm RTC battery connector for low power
                 RTC IC HYM8563TS
    5V Fan connector
    Working Temperature: 0C to 70C
    Power: 5.5*2.1mm DC Jack, 12VDC input
    Dimensions: 110x80x1.6mm (without case) / 86x114.5x30mm (with case)

Kernel commits:
893c17716d0c ("arm64: dts: rockchip: Add NanoPC T6")
a721e28dfad2 ("arm64: dts: rockchip: Add NanoPC T6 PCIe Ethernet support")
ac76b786cc37 ("arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support")

Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-10-23 18:21:55 +08:00
Andre Przywara
fa066df62e sunxi: add MangoPi MQ-R board support
The MangoPi MQ-R board uses an Allwinner T113s Soc (with 128MB of
embedded DRAM), support for which was just added to the code.

Since the devicetree was already synced from the latest Linux kernel
tree, all we need is a _defconfig file to add support for the board.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2023-10-23 01:00:56 +01:00
Tom Rini
e65b5d35c9 Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sh
- RZ/G2L part 1, except for two serial port patches which I had to drop
  as they broke R2Dplus, they will come later via subsequent PR.
2023-10-17 09:15:56 -04:00
Paul Barker
e3e01a6f94 arm: dts: Import RZ/G2L SMARC EVK device tree
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.

This patch is based on the corresponding Linux v6.5 device tree
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).

Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
2023-10-17 03:27:42 +02:00
Tom Rini
c41df16b27 u-boot-imx-20231016
-------------------
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/18168
 
 - Imrovement MX93
 - Toradex: fixes
 - Convert to DM (serial, watchdog) for some boards
 - HAB improvements for Secure Boot
 - DTO overlay for DHCOM
 - USB fixes, Mass storage for MX28
 - Cleanup some code
 - Phytec MX8M : EEProm detection, fixes
 - Gateworks Boards improvements
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZS2rbg8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76ZdfQCgi+D4n5iiQglY1zy34TkQogK1b/wAoI/8yu79
 SxE769moFjYPyYOZMjtt
 =GGb5
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20231016' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20231016
-------------------

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/18168

- Imrovement MX93
- Toradex: fixes
- Convert to DM (serial, watchdog) for some boards
- HAB improvements for Secure Boot
- DTO overlay for DHCOM
- USB fixes, Mass storage for MX28
- Cleanup some code
- Phytec MX8M : EEProm detection, fixes
- Gateworks Boards improvements
2023-10-16 17:34:38 -04:00
Marek Vasut
24985686fe arm64: dts: imx8mp: Add DT overlay describing i.MX8MP DHCOM SoM rev.100
The current imx8mp-dhcom-som.dtsi describes production rev.200 SoM,
add DT overlay which reinstates rev.100 SoM description to permit
prototype rev.100 SoMs to be used until they get phased out.

Signed-off-by: Marek Vasut <marex@denx.de>
2023-10-16 16:25:10 +02:00
Marek Vasut
ad1158c50e arm64: dts: imx8mp: Switch to DT overlays for i.MX8MP DHCOM SoM
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.

Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().

Signed-off-by: Marek Vasut <marex@denx.de>
2023-10-16 16:25:10 +02:00
Tony Dinh
b3f559a147 arm: kirkwood: Add support for ZyXEL NSA325 board
ZyXEL NSA325 specifications:

Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console

Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2023-10-16 11:10:42 +02:00
Tim Harvey
52346fcb90 board: gateworks: venice: add imx8mm-gw7905-0x support
The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.

The GW700x SOM contains the following:
 - i.MX8M Mini SoC
 - LPDDR4 memory
 - eMMC Boot device
 - Gateworks System Controller (GSC) with integrated EEPROM, button
   controller, and ADC's
 - RGMII PHY
 - PMIC
 - SOM connector providing:
  - FEC GbE MII
  - 1x SPI
  - 2x I2C
  - 4x UART
  - 2x USB 2.0
  - 1x PCI
  - 1x SDIO (4-bit 3.3V)
  - 1x SDIO (4-bit 3.3V/1.8V)
  - GPIO

The GW7905 Baseboard contains the following:
 - GPS
 - microSD
 - off-board I/O connector with I2C, SPI, GPIO
 - EERPOM
 - PCIe clock generator
 - 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
 - 1x half-length miniPCIe socket with USB2.0 and USB3.0
 - USB 3.0 HUB
 - USB Type-C with USB PD Sink capability and peripheral support
 - USB Type-C with USB 3.0 host support

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-10-16 08:46:01 +02:00
Tim Harvey
8aa5e6973c board: gateworks: venice: add imx8mp-gw73xx-2x support
The Gateworks imx8mp-venice-gw73xx-2x consists of a SOM + baseboard.

The GW702x SOM contains the following:
 - i.MX8M Plus SoC
 - LPDDR4 memory
 - eMMC Boot device
 - Gateworks System Controller (GSC) with integrated EEPROM, button
   controller, and ADC's
 - PMIC
 - SOM connector providing:
  - eQoS GbE MII
  - 1x SPI
  - 2x I2C
  - 4x UART
  - 2x USB 3.0
  - 1x PCI
  - 1x SDIO (4-bit 3.3V)
  - 1x SDIO (4-bit 3.3V/1.8V)
  - GPIO

The GW73xx Baseboard contains the following:
 - 1x RJ45 GbE (eQoS from SOM)
 - 1x RJ45 GbE (PCI)
 - off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
 - off-board I/O connector with RS232/RS485
 - off-board I/O connector with SPI
 - off-board I/O connector with I2C, UART, and GPIO
   I2C, I2S and GPIO
 - microSD (1.8V/3.3V)
 - GPS
 - Accelerometer
 - EERPOM
 - USB 3.0 Hub
 - Front Panel bi-color LED
 - re-chargeable battery (for RTC)
 - PCIe clock generator
 - PCIe switch
 - on-board 802.11abgnac 1x1 WiFi and Bluetooth 5.2
 - 1x USB Type-A host socket with USB 3.0 support
 - 1x USB OTG with USB 2.0 support
 - 2x MiniPCIe socket with PCI and USB 2.0
 - 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
 - Wide range DC input supply

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-10-16 08:46:01 +02:00
Tim Harvey
e55422a113 board: gateworks: venice: add imx8mp-gw72xx-2x support
The Gateworks imx8mp-venice-gw72xx-2x consists of a SOM + baseboard.

The GW702x SOM contains the following:
 - i.MX8M Plus SoC
 - LPDDR4 memory
 - eMMC Boot device
 - Gateworks System Controller (GSC) with integrated EEPROM, button
   controller, and ADC's
 - PMIC
 - SOM connector providing:
  - eQoS GbE MII
  - 1x SPI
  - 2x I2C
  - 4x UART
  - 2x USB 3.0
  - 1x PCI
  - 1x SDIO (4-bit 3.3V)
  - 1x SDIO (4-bit 3.3V/1.8V)
  - GPIO

The GW72xx Baseboard contains the following:
 - 1x RJ45 GbE (eQoS from SOM)
 - 1x RJ45 GbE (PCI)
 - off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
 - off-board I/O connector with RS232/RS485
 - off-board I/O connector with SPI
 - off-board I/O connector with I2C, UART, and GPIO
   I2C, I2S and GPIO
 - microSD (1.8V/3.3V)
 - GPS
 - Accelerometer
 - EERPOM
 - USB 3.0 Hub
 - Front Panel bi-color LED
 - re-chargeable battery (for RTC)
 - PCIe clock generator
 - PCIe switch
 - 1x USB Type-A host socket with USB 3.0 support
 - 1x USB OTG with USB 2.0 support
 - 1x MiniPCIe socket with PCI and USB 2.0
 - 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
 - Wide range DC input supply

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-10-16 08:46:01 +02:00
Tim Harvey
6db1085623 board: gateworks: venice: add imx8mp-gw71xx-2x support
The Gateworks imx8mp-venice-gw71xx-2x consists of a SOM + baseboard.

The GW702x SOM contains the following:
 - i.MX8M Plus SoC
 - LPDDR4 memory
 - eMMC Boot device
 - Gateworks System Controller (GSC) with integrated EEPROM, button
   controller, and ADC's
 - PMIC
 - SOM connector providing:
  - eQoS GbE MII
  - 1x SPI
  - 2x I2C
  - 4x UART
  - 2x USB 3.0
  - 1x PCI
  - 1x SDIO (4-bit 3.3V)
  - 1x SDIO (4-bit 3.3V/1.8V)
  - GPIO

The GW71xx Baseboard contains the following:
 - 1x RJ45 GbE (eQoS from SOM)
 - off-board I/O connector with I2C, SPI, UART, and GPIO
 - Front Panel bi-color LED
 - re-chargeable battery (for RTC)
 - PCIe clock generator
 - 1x USB Type-C connector supporting USB 2.0 host mode with VBUS
 - 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
 - GPS
 - Accelerometer
 - EERPOM
 - Wide range DC input supply

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-10-16 08:46:01 +02:00
Tom Rini
6961ca0a46 Xilinx changes for v2024.01-rc1 v3
clk:
 - remove additional compatible strings for Versal NET
 
 net:
 - zynq_gem: Fix clock calculation for MDC for higher frequencies
 
 pinctrl:
 - core: Extend pinmux status buffere size
 - zynqmp driver: Show also tristate configuration
 
 test:
 - add test case for pxe get
 
 Xilinx:
 - describe SelectMAP boot mode
 
 Zynq:
 - Fix nand description in DT
 
 ZynqMP:
 - DTS sync patches with kernel and also W=1 related fixes
 - Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
   description for other SC based boards
 - k24 psu_init cleanup
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
 IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
 =u1bz
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2024.01-rc1 v3

clk:
- remove additional compatible strings for Versal NET

net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies

pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration

test:
- add test case for pxe get

Xilinx:
- describe SelectMAP boot mode

Zynq:
- Fix nand description in DT

ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
  description for other SC based boards
- k24 psu_init cleanup
2023-10-13 08:45:55 -04:00
Michal Simek
b51371e8c9 arm64: zynqmp: Add support for zcu670-revB
RevB has different SD level shifter compare to revA. There are couple of
changes between revisions but none of them requires SW alignment.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/0f2bb29f88615ce75f887c006060543b4aeafd48.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
1ddf10d178 arm64: zynqmp: Add support for zcu670-revA
The board is sharing a lot of components with zcu208 but it contains
differet silicon and also several components are done differently.
The board has 4GB memory connected to PS and additional 4GB connected to
PL. Compare to zcu208 sata support has been dropped and only USB3.0 is
using GTR (lane2). Others GTRs are routed to connectors.

MIO configuration is also shared with zcu111.

The board is using si5381 chip compare to si5341 which is normally used.
And as of now there is no Linux driver for this chip. PS reference clock is
generated out of si570 chip which is also new approach compare to zcu208.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3b296ef0f52bd94e32bdeb6d1beee29ac85f00a2.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
eb357b75b7 arm64: zynqmp: Add support for VPXA2785
VPXA2785(vp-x-a2785-00) is evaluation board which contains two PCIe-Edge
fingers, one for PCIe-B(gen5x8) and one for CPM(dual gen5x8, gen5x16).
Each of the ports can operate in endpoint or root port mode. This allows
the single card to be used for both root port, endpoint, and switch modes.

The board is designed in the similar manner as others Versal boards. It
means board also have ZynqMP Zu4 System Controller which is described in a
separate file.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/59d3b1f7e785bc65518b465e5122fd2787616a93.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
7f3639918f arm64: zynqmp: Describe i2c structures for SCs
Generic system controller (SC) covers connection defined by specification
but different boards have different i2c devices. That's why describe i2c
devices available on multiple boards.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ca1826b8b58981111229a94527818cc5a191ca9a.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
fa822ad19e arm64: zynqmp: Add support for SC revC
System controller revC is using ADI ethernet phy instead of TI because of
supply chain issues.
Describe reset assert and de-assert times to 10us and 5ms respectively
according to the datasheet. Also setup RGMII RX and TX delay values to
2400ps as per board bring up observations.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2790f6cede7485556d581ab8270dda477fa21522.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
64f5e3b492 arm64: zynqmp: Create description for generic SC (vpk120-revB)
System controllers are pretty much the same on the all boards that's why
use autodetection based on i2c eeprom. This should end up with having only
one BSP for all SCs with only DT overlays to cover different i2c
structures.

All MIOs are fixed by the spec that's why not a problem to description
pinctrl setting.

Apart from eth phy reset, it also set proper phy delays.
The TI DP83867 PHY datasheet says:
T1: Post RESET stabilization time == 195us
T3: Hardware configuration pins transition to output drivers == 64us
T4: RESET pulse width == 1us
So with a little overhead set 'reset-assert-us' to 100us (T4) and
'reset-deassert-us' to 280us (T1+T3).

NOTE: The tuning of TI DP83867 phy reset delay is derived from linux
upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron
pitx-imx8m board).

i2c structure on Xilinx Versal evaluation platforms contain a lot of
devices but also connection to connectors like SFP. Because of this
complicated structure with also all level shifters, i2c muxes, etc. not all
devices are able to reliably work on 400kHz even if they are compatible
with this speed. That's why set i2c frequency to 100KHz to increase
reliability of the i2c bus.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
fe90ce2368 arm64: zynqmp: Add support for vpk120-revA
Board contains two systems. The primary is Versal VP1202 ACAP device and
the secondary is ZynqMP zu4 which acts as system controller. The patch is
describing only ZynqMP system controller part.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/bd8b79d7c6693e90e12bce422f8ed00f2f43c9ae.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
96e98b0264 arm64: zynqmp: Add x-prc-01/02/03/04/05 revA support from SC
Add i2c accessible devices with description.
There is versal specific eeprom and i2c-gpio controller.

SE3 has also clock chip present.

Also remove x-prc description from SC dts.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4f71ec6a63240fd4aaa3453824138281c50d71c3.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
46f0408771 arm64: zynqmp: Add support for vck190 revB system controller
There are some changes between revA and revB boards. u39 8T49N240 was
removed and also three ina226 at 42/43/44 addresses (u178/u180/u182).

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/461cfe5b2b882365413f90d19efd8abcd6be56ed.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:29 +02:00
Michal Simek
7771873ab4 arm64: zynqmp: Add support for KD240 Kria SOM CC
Add support for KD240 Kria SOM CC. It is pretty much subset of KR260 board
from PS perspective.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/835f1d1b8982d46b902db69daad64e8445c051e9.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:29 +02:00
Frank Wunderlich
3d96c3f5ec board: rockchip: Add Bananapi R2Pro Board
Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
2023-10-07 16:49:41 +08:00
Robert Nelson
45b0b5e5a0 arm: dts: Add k3-am625-beagleplay
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.

This board family can be identified by the 24c32 eeprom:

[aa 55 33 ee 01 37 00 10  2e 00 42 45 41 47 4c 45  |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d  00 00 30 32 30 30 37 38  |PLAY-A0-..020078|]

https://beagleplay.org/
https://git.beagleboard.org/beagleplay/beagleplay

baseline of base device tree is v6.5-rc1.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2023-09-08 10:07:12 -04:00
Tom Rini
c37be6a39a First set of u-boot-at91 features for the 2023.10 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
 aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
 Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
 kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
 +Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
 s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
 tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
 +fcB
 =L/iw
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next

First set of u-boot-at91 features for the 2023.10 cycle:

This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
2023-08-30 09:32:10 -04:00
Tom Rini
2d8e7ac320 ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
 has some other minor enhancements, such as enabling the poweroff command
 on several Tegra210 and Tegra186 boards.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmTfWrITHHRyZWRpbmdA
 bnZpZGlhLmNvbQAKCRDdI6zXfz6zoYPFD/9hw40HjaAXf6cD960HWSlcGuNOIV99
 A9JoSgHipCuhACr0z7s4MpbATjEgknZUblJNiVdhzCWAgW3Spy9JpSxMyKlpqdiH
 7Z971DuaXFX9ZCilX9g6whZI/RDglpUEjt3cb4PWrznM6dpKA73voizo+czBeXd7
 AhxTN/2I89VLz75RyR+X41bLLK1VuGND+uGHz/DDbpMXEW8gVRtZ8gnJPeR4zg1y
 EUacNFc+PVjghMFZGmClnw0pXkq2akKp5cJ/A+11aa/Q7FII63v5/Np79kDtnUje
 GPSdg4yqSr1ZE/6qK0qV58B2KKHfeg+6GC47s46KjzaUwL4De64zHtCt6t37zz8y
 hngeeR5SYIKR8HkpXKM8DsMv0D1WciP2awggFPaPF802H/5GMVCnEFITmuFlOuAe
 Q1lg2acywMo2NFINMOONuQahGIJZORpm2VMonMhlesyAuc89quslt/iYSAoV9E4/
 Pt1AqgeOpUh5I236EygJJ11V2BAXkwzR6RazFDr3AHCqB9iFW/UNS1Y7A1pXwKYN
 IVUWU8xkuYYSyxeGwuIrTj/JdQhwfO0jn+xn5g+rUPWNP5n4FJ2oBVPOInfEpled
 k0HgxcGK6Z0hBCwd6/t03QQJWD47/r5jAd9x1eLRFWYV8ivl2Acvm+MlkPx81weG
 E1h7UKdfvTZcDw==
 =Bzgn
 -----END PGP SIGNATURE-----

Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra

ARM: tegra: Changes for v2023.10-rc1

This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
2023-08-18 10:05:04 -04:00
Andy Yan
bb38db086c rockchip: rk3568: Add EmbedFire Lubancat 2 support
LubanCat2 is a rk3568 based SBC from EmbedFire.

Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header

The dts file is sync from linux mainline.

Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-08-12 10:17:59 +08:00
Mihai Sain
87d1cac49d board: at91: sama5d29_curiosity: add initial support for sama5d29_curiosity
Add initial support for sama5d29_curiosity board.

Hardware:
SoC: SAMA5D29 500 MHz
DRAM: LPDDR2 512 MiB
PMIC: MCP16502
Debug: UART0
Flash: QSPI NOR 8 MiB
RGB LCD connector
Mikrobus connectors x 2
SD-Card connectors x 2
USB 2.0 x 2

Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
2023-08-07 11:42:16 +03:00
Marcel Ziswiler
7d1a10659f board: toradex: add verdin am62 support
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.

The device trees were taken straight from Linux v6.5-rc1.

Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
  ---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
2023-08-04 15:03:42 -04:00
Weijie Gao
bc4adc97cf board: mediatek: add MT7988 reference boards
This patch adds general board files based on MT7988 SoCs.

MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:

1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2023-08-03 09:40:50 -04:00
Jonas Karlman
1f54f71b18 board: rockchip: Add Radxa E25 Carrier Board
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.

Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA

Device tree is imported from linux next-20230728.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
2023-07-31 20:34:32 +08:00
Eugen Hristev
b8fc65473a board: rockchip: add Radxa ROCK5A Rk3588 board
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.

There are tree variants depending on the DRAM size : 4G, 8G and 16G.

Specifications:

     Rockchip Rk3588S SoC
     4x ARM Cortex-A76, 4x ARM Cortex-A55
     4/8/16GB memory LPDDR4x
     Mali G610MC4 GPU
     MIPI CSI 2 multiple lanes connector
     4-lane MIPI DSI connector
     Audio – 3.5mm earphone jack
     eMMC module connector
     uSD slot (up to 128GB)
     2x USB 2.0, 2x USB 3.0
     2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
     Gigabit Ethernet RJ45 with optional PoE support
     40-pin IO header including UART, SPI, I2C and 5V DC power in
     USB PD over USB Type-C
     Size: 85mm x 56mm (Raspberry Pi 4 form factor)

Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")

Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
6855fa625c board: rockchip: Add Pine64 SOQuartz on CM4-IO
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:36 +08:00
Jonas Karlman
d0026e5908 board: rockchip: Add Pine64 SOQuartz on Blade
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
651492bfb2 board: rockchip: Add Pine64 SOQuartz on Model A
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00