Update the code and the configs for eMMC boot and userdata
partitions acces
- FASTBOOT_MMC_BOOT_SUPPORT: boot partition 1 and 2 (erase/write)
- FASTBOOT_MMC_BOOT1_NAME: boot partition 1, default name="mmc0boot0"
- FASTBOOT_MMC_BOOT2_NAME: boot partition 2, default name="mmc0boot1"
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).
The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add configs for voltage switching and UHS modes for the SD card
and HS200 for the eMMC.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add configs to support UHS modes for the SD card and HS200 for the eMMC.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add configs to support UHS modes for the SD card and HS200 for the eMMC.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
With commit 38d6b7ebda ("spl: Drop bd_info in the data section") you
need to enable this option to boot from mmc.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.
Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This disables booting to non-Linux OSes.
This board is uncomfortably close to its 256K size limit, so every
few KB saved helps.
Signed-off-by: David Lechner <david@lechnology.com>
This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.
This also fixes the warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: David Lechner <david@lechnology.com>
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image
With the recent addition of ACPI generation, the image size has got beyond
its current limit.
Samus does not actually use this, nor x86 emulation for PCI ROMs, so
disable both features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With the fixes to the sun8i-emac driver, we can now enable Ethernet
support on the OrangePi Zero2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
These cannot work with of-platdata since they currently need the
devicetree at runtime. Disable the emulators and the sandbox I2C driver
that needs them. We can enable these later, if needed for testing.
Switch the of_plat_parent test over to use a simple bus instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Enable this option so that the boot-script substitutions of %U works as
expected. With this, it can boot into Chrome OS.
Signed-off-by: Simon Glass <sjg@chromium.org>
1. Enable MTK SPI NOR controller driver on mt7622 & mt7629.
2. Enable quad mode for read and single mode for write.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Add CAxxxx Ethernet support for the Cortina Access
Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Enable setexpr command in defconfig for Turris MOX. We have found that
this is sometimes useful in U-Boot scripts and there is enough space in
NOR memory on MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable wdt command in defconfig for Turris MOX. This is useful when
doing debugging.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Since mt7620 is added into Kconfig, the CONFIG_SOC_MT7628=y which is
omitted by default must be added back, otherwise make xxx_defconfig for
these boards will be configured for mt7620 platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.
The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is a QSPI chip connected to the FSPI. Enable the defconfig
to support it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Supported boot device types in iMX8MQ: MMC, DHCP.
CONFIG_DISTRO_DEFAULTS is added for enabling the DISTRO_DEFAULTS option.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mq_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables because "run distro_bootcmd" is
set to be the default boot mode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Move the bootcounter to SVNS_LPGDR to free up OCRAM for usage by the VPU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Because SPL can support SD UHS, the fixed regulator needs to be
enabled in SPL to reset the SD card.
Fixes: 1a5d9c84b4 ("imx8mm_beacon: Enable HS400 on MMC controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
This fixes eth0 not initializing properly. Both eth0 and eth1 use the
MDIO interface on eth1 to access their PHYs. However, without
DM_ETH_PHY, eth0 still tries to use its own MDIO interface to access its
phy. Before this patch, a boot log might contain lines like
Net:
Warning: ethernet@20b4000 using MAC address from ROM
eth1: ethernet@20b4000 [PRIME]Could not get PHY for FEC0: addr 2
After this patch they now look like
Net:
Warning: ethernet@20b4000 using MAC address from ROM
eth1: ethernet@20b4000 [PRIME]Get shared mii bus on ethernet@2188000
Warning: ethernet@2188000 using MAC address from ROM
, eth0: ethernet@2188000
As an alternative to DM_ETH_PHY, FEC_MXC_SHARE_MDIO could also have been
used to achieve the same effect.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Supported boot device types in iMX8MP: MMC.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution. kernel_addr_r is the location in RAM where
the kernel will be loaded to. Delete unnecessary environment variables
because "run distro_bootcmd" is set to be the default boot mode.
On the iMX8MP platform I used, "mmc1" represents SD card and "mmc2"
represents eMMC.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is
for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
When CONFIG_ATMEL_NAND_HW_PMECC is set, CONFIG_PMECC_CAP defaults
to the value of 2. At the conversion to Kconfig for the PMECC config
values, some boards/defconfigs were wrongly configured.
Update CONFIG_PMECC_CAP to the PMECC_CAP value before the conversion.
Fixes: 49ad40298c ("ARM: at91: Convert SPL_GENERATE_ATMEL_PMECC_HEADER to Kconfig")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
SPL_GENERATE_ATMEL_PMECC_HEADER selects:
ATMEL_NAND_HWECC [=y] && ATMEL_NAND_HW_PMECC [=y].
With the removal of SPL_GENERATE_ATMEL_PMECC_HEADER,
ATMEL_NAND_HW_PMECC and ATMEL_NAND_HWECC were no longer
selected. Also, when the SPL_GENERATE_ATMEL_PMECC_HEADER was removed,
the configs were not updated using savedefconfig, thus the
'commit d168bcb6fe ("configs: Resync with savedefconfig")'
further removes the CONFIG_PMECC_CAP value.
Update defconfigs and add CONFIG_ATMEL_NAND_HW_PMECC,
which selects ATMEL_NAND_HWECC, in order to restore NAND PMECC
support. Restore CONFIG_PMECC_CAP value.
Fixes: 57f76c2a47 ("configs: at91: remove SPL_GENERATE_ATMEL_PMECC_HEADER from non-nand configs")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Enable the RNG on the Firefly, rock960 and RockPro64 devices
to enable KASLR on devices that support it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Akash Gajjar <akash@openedev.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
