Commit graph

16097 commits

Author SHA1 Message Date
Nicolas Ferre
b2f2643b39 net: phy: micrel: make sure the factory test bit is cleared
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet).
Create another ksz8081_config function to handle this case.

Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Florin Chiculita
bf58916373 net: phy: aquantia: wait for phy init sequence to finish
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.

Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Josef Holzmayr
7c56408be6 net: macb: let miiphy_read/_write pass arbitrary addresses
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.

Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Josef Holzmayr
0d3044c210 net: macb: explicitly pass phy_adr to mdio read and write
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.

The function signature is extended according to the Linux kernel
equivalent.

Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Stefan Roese
27c3f70f3b net: phy: Increase link up delay in genphy_update_link()
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Thierry Reding
945dd965dd net: rtl8169: Support RTL-8168c/8111c
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Nevo Hed
17caaf8a9d net: mvpp2: MVPP2 now needs MVMDIO
Changes to mvpp2.c require the MVMDIO module which in turn uses
DM_MDIO.

Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Nevo Hed
2a42870778 net: mvpp2: use new MVMDIO driver
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver.  It removes direct interaction with the SMI & XSMI
busses.  This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.

The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot.  With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.

Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grzegorz Jaszczyk
623948377a net: mvpp2: mark phy as invalid in case of missing appropriate driver
If the phy doesn't match with any existing u-boot drivers, the phy
framework will connect it to the generic one which uid ==
0xffffffff. In this case, act as if the phy wouldn't be declared in
dts. Otherwise, in case of 3310 (for which the driver doesn't exist)
the link is marked as always down. Removing phy entry from dts in case
of 3310 is not a good option because it is required for the
phy_fw_down procedure.

This patch fixes the issue with the link always down on MCBIN board.

nhed: added NULL deref test.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Stefan Chulski
13b725fd24 net: mvpp2x: fix traffic stuck after PHY start error
Issue:
- Network stuck if autonegotion fails.

Issue root cause:

- When autonegotiation fails during port open procedure, the packet
  processor configuration does not finish and open procedure exits
  with error.
- However, this doesn't prevent u-boot network framework from
  calling send and receive procedures.
- Using transmit and receive functions of misconfigured packet
  processor will cause traffic to get stuck.

Fix:

- Continue packet processor configuration even if autonegotiation
  fails.  Only error message is triggered in this case.
- Exit transmit and receive functions if there is no PHY link
  indication.
- U-boot network framework now calls open procedure again during next
  transmit initiation.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
37d6265f2b net: phy: dp83867: refactor rgmii configuration
Refactor SGMII configuration to group all settings together and reduce
number of MDIO transactions.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
253a5ff871 net: phy: dp83867: io impedance is not dependent on RGMII delay
Based on commit 27708eb5481b ("net: phy: dp83867: IO impedance is not
dependent on RGMII delay") of mainline linux kernel.

The driver would only set the IO impedance value when RGMII internal delays
were enabled.  There is no reason for this.  Move the IO impedance block
out of the RGMII delay block.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
20f7ea4c35 net: phy: dp83867: rework delay rgmii delay handling
Based on commit c11669a2757e ("net: phy: dp83867: Rework delay rgmii delay
handling") of mainline linux kernel.

The current code is assuming the reset default of the delay control
register was to have delay disabled.  This is what the datasheet shows as
the register's initial value.  However, that's not actually true: the
default is controlled by the PHY's pin strapping.

This patch:
- insures the other direction's delay is disabled If the interface mode is
selected as RX or TX delay only
- validates the delay values and fail if they are not in range
- checks if the board is strapped to have a delay and is configured to use
"rgmii" mode and warning is generated that "rgmii-id" should have been
used.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
b3b9b128d5 net: phy: dp83867: Add ability to disable output clock
Based on commit 13c83cf8af0d ("net: phy: dp83867: Add ability to disable
output clock") of mainline linux kernel.

Generally, the output clock pin is only used for testing and only serves as
a source of RF noise after this.  It could be used to daisy-chain PHYs, but
this is uncommon.  Since the PHY can disable the output, make doing so an
option.  I do this by adding another enumeration to the allowed values of
ti,clk-output-sel.

The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output.  Rather it meant "keep clock
output setting as is", which, depending on PHY strapping, might not be
outputting REF_CLK.

Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the previous
behavior in this case).

Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK.
Change this so they generate an error.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
ee622f03cc net: phy: dp83867: move static initialization to .probe()
Move static, one-time initialization to .probe() callback.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Grygorii Strashko
5ee989c5aa net: phy: ti: rename ti.c to dp83867.c
The driver ti.c is actually driver for TI DP83867x PHYs, so rename it
accordingly.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
Priyanka Jain
1f60789602 net/phy: Fix phy_connect() for phy addr 0
Fix 'mask' calculation in phy_connect() for phy addr '0'.
'mask' is getting set to '0xffffffff' for phy addr '0'
in phy_connect() whereas expected value is '0'.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: tetsu-aoki via github
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-12-09 09:47:42 -06:00
AKASHI Takahiro
05429b6cf5 rtc: move date.c from drivers/rtc/ to lib/
In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2019-12-06 16:44:19 -05:00
Tom Rini
bead4f2f2c Merge tag 'u-boot-rockchip-20191206' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
2019-12-06 10:35:18 -05:00
David Wu
41eee945ce pinctrl: rockchip: Add pinctrl support for rk3308
An iomux register contains 8 pins, each of which is represented
by 2 bits, but the register offset is 0x8.

For example, GRF_GPIO0A_IOMUX offset is 0x0, but GRF_GPIO0B_IOMUX
offset is 0x8, the offset 0x4 is reserved.

So add a type IOMUX_8WIDTH_2BIT to calculate offset.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
David Wu
4ee6d51c5a pwm: rk_pwm: Make PWM driver to support all Rockchip Socs
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.

The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.

The RK3288 keep the current functions.

RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
David Wu
0ed8f1e5f4 net: gmac_rockchip: Add support for rk3308
Add the glue code to allow the rk3308 variant of the Rockchip gmac
to provide network functionality.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
Thomas Hebb
9f67b56772 Fix typo in macros, "FIRMEWARE" -> "FIRMWARE"
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
2019-12-05 10:28:39 -05:00
Jorge Ramirez-Ortiz
2464b229b5 drivers: optee: rpmb: fix returning CID to TEE
The mmc CID value is one of the input parameters used to provision the
RPMB key. The trusted execution environment expects this value to be
specified in big endian format.

Before this fix, on little endian systems, the value returned by the
linux kernel mmc driver differed from the one returned by u-boot.
This meant that if linux provisioned the RPMB key, u-boot would not
have access to the partition (and the other way around).

Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
2019-12-05 10:28:38 -05:00
Michael Walle
a6cd597a78 drivers: pci: ignore disabled devices
PCI devices may be disabled in the device tree. Devices which are probed
by the device tree handle the "status" property and are skipped if
disabled. Devices which are probed by the PCI enumeration don't check
that property. Fix it.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-05 10:28:38 -05:00
Miquel Raynal
fb4384490d mtd: Makefile: deep cleanup
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).

Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
eb446ef625 cmd: nand/sf: isolate legacy code
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.

This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
85f7e9d547 mtd: spi: SPI_FLASH_MTD depends on MTD
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.

Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
f3a02d29e8 dfu: add dependency on the raw NAND core
CONFIG_DFU_NAND needs the raw NAND core being compiled.

Also fix the colibri_vf defconfig to reflect this dependency.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
c8f555f102 mtd: nand: add includes in NAND core to avoid warnings
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
888f184abe mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD
Like in Linux, just use CONFIG_MTD to compile the MTD stack.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
1de770d544 mtd: rename CONFIG_MTD -> CONFIG_DM_MTD
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Tom Rini
a7bbaf8c13 Fix stdout-path handling
-----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl3mkWwACgkQfxc6PpAI
 rebncAf/SvjTDzKZZiCsSKakHr2YJmID1GwCg9HI3vBxJH2vjsdWKBBg7THmaqve
 ST/haRump2HXPBTEHtqIo3wSFkopuzGFmAa/20bpCDoGoJdLrwzWbS1SgPcPNr2m
 gqTbkWweNej+dndM1sYG/Fv5hzWqBfZvKah9vYyW9V6AaIW7r3Ahe+thkpOETKRq
 QT1fe8Y2L25xTRqad5DuvEj0JkRR2RYBInZWp0NkcyoTFRpZUoV7ZVMlMMjgn4b/
 dVJtdDRozURGbbV9F7DmvEpfFMoWfaEn6Q3gsRfuhDBLlil1iYikhsjURyspPgxt
 NNBzgEkxKDeZksLcqNnyG7GKZWp20g==
 =SOs9
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-3dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm

Fix stdout-path handling
2019-12-03 18:12:04 -05:00
mingming lee
485627dd5f pinctrl: add driver for MT8518
Add Pinctrl driver for MediaTek MT8518 SoC.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2019-12-03 08:44:14 -05:00
mingming lee
69373bd44a mmc: mtk-sd: Adjust the mmc tuning flow
1.Support cmd response and data tuning together.
2.Support hs400 cmd responese tuning.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2019-12-03 08:44:14 -05:00
mingming lee
9072400775 clk: mediatek: add driver for MT8518
Add clock driver for MediaTek MT8518 SoC.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2019-12-03 08:44:14 -05:00
Faiz Abbas
42a4ee8a11 regmap: Fix potential memory leaks
Free allocated memory in case of an error in regmap_init_mem() and
regmap_init_mem_index().

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-12-03 08:44:14 -05:00
Faiz Abbas
ae3ef109c3 net: cpsw: Add NULL pointer check
Add null pointer check to take care of out of memory errors.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
2019-12-03 08:44:14 -05:00
Bartosz Golaszewski
3ef94715cc mmc: davinci: fix mmc boot in SPL
The MMC boot is currently broken on omapl138-lcdk after enabling the
driver model in SPL. The main problem is the driver's bind callback not
being called after probe in SPL (even with the DM_FLAG_PRE_RELOC flag
specified).

While a proper fix is still being worked on, this hacky changeset at
least fixes the MMC boot on this platform by calling mmc_bind()
manually from probe().

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:14 -05:00
Bartosz Golaszewski
21a4d80a71 mmc: davinci: drop struct davinci_mmc_plat
struct mmc_config & struct mmc don't need to be exported over platform
data, but can instead be private in the driver.

Remove struct davinci_mmc_plat.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:13 -05:00
Bartosz Golaszewski
6a97153cbf mmc: davinci: drop support for ti,dm6441-mmc
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:13 -05:00
Tom Rini
4df23e58a4 blk: Make use of CONFIG_HAVE_BLOCK_DEVICE more
When we do not have CONFIG_BLK (or SPL/TPL) enabled there are very few
cases where we need the blk_legacy code linked in. To catch these, build
when we have CONFIG_HAVE_BLOCK_DEVICE set.  In addition, we only need
cmd/blk_common.o to be linked in when we have CONFIG_HAVE_BLOCK_DEVICE
set, so make use of that directly.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Tom Rini
56e5a39346 mtd: mtdcore: Drop unused mtd_table
The array 'mtd_table' is unused in the code.  Remove this as gcc doesn't
always discard unused global variables.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Tom Rini
923e211f8d pci: Only link pci_rom.o in some cases
The content of pci_rom.c is only used in a few cases.  Only build and
link in these cases to avoid a global variable as gcc doesn't always
discard those when they are unused.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Tom Rini
e78f16b751 Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_CORTINA_FW_IN_MMC
   CONFIG_SYS_CORTINA_FW_IN_NAND
   CONFIG_SYS_CORTINA_FW_IN_NOR
   CONFIG_SYS_CORTINA_FW_IN_REMOTE
   CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Thomas Hebb
6920f00c2c Kconfig: make TPL_DM_SERIAL depend on TPL_DM
This missing dependency seems like an oversight, since all other
TPL_DM_* options have it.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
2019-12-03 08:43:23 -05:00
Simon Glass
cb3ef6810a common: Move old EEPROM functions into a new header
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:25 -05:00
Simon Glass
2cf431c228 common: Move pci_init_board() out of common.h
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:25 -05:00
Simon Glass
67c4e9f815 common: Move board_get_usable_ram_top() out of common.h
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:04 -05:00