Register value table for DDR PHY clock divider are wrong. They should be
0 or 1 for divide-by-2 or divide-by-4, respectively. Not 1 or 2. Current
values do not make sense, since 2 cannot be achieved, because the
register is only 1 bit long (mask is set to 1).
This fixes clk dump reporting DDR PHY clock rate differently from Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The current exit codes of 128 and 129 are useful in that they do not
conflict with those returned by tools, but they are not actually valid.
It seems better to pick some codes which work with 'bit bisect run'.
Update them to 100 (for errors) and 101 (for warnings).
Signed-off-by: Simon Glass <sjg@chromium.org>
These are becoming more common now. They cause boards to show warnings
which can be mistaking for compiler warnings.
Add a buildman option to ignore them. This option works only with the
summary option (-s). It does not affect the build process.
Signed-off-by: Simon Glass <sjg@chromium.org>
Unfortunately the plague of device-tree warnings has not lifted. These
warnings infiltrate almost every build, adding noise and confusion.
Add a buildman option to ignore them. This option works only with the
summary option (-s). It does not affect the build process.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present buildman defaults to running 'mrproper' on every thread before
it starts building commits for each board. This can add a delay of about 5
seconds to the start of the process, since the tools and other invariants
must be rebuilt.
In particular, a build without '-b', to build current source, runs much
slower without -I, since any existing build is removed, thus losing the
possibility of an incremental build.
Partly this behaviour was to avoid strange build-system problems caused by
running 'make defconfig' for one board and then one with a different
architecture. But these problems were fixed quite a while ago.
The -I option (which disabled mrproper) was introduced four years ago and
does not seem to cause any problems with builds.
So make -I the default and deprecate the option. To allow use of
'mrproper', add a new -m flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
When buildman finishes it leaves the last summary line visible, which
shows the number of successful builds, builds with warnings and builds
with errors.
It is useful also to see how many builds were done in total along with
the time taken. Show these on a separate line before buildman finishes.
Signed-off-by: Simon Glass <sjg@chromium.org>
If a progress message is longer than the terminal line it will scroll the
terminal. Limit the messages to the terminal width.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is nice to see the actual number of builds remaining to complete. Add
this in the progress message, using a different colour.
Drop the unnecessary 'name' variable while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The commit counter is a hangover from when buildman processed each board
for a commit. Now buildman processes each commit for a board, so this
output is never triggered.
Delete it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fetching updated versions of a repo can take time. At present buildman
gives no indication that it is doing this.
Add a message to explain the delay.
Tidy up a few other messages while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
When outputing a progress line we don't want it to go past the end of the
current terminal line, or it will not be possible to erase it. Add an
option to Print() which allows limiting the output to the terminal width.
Since ANSI sequences do not take up space on the terminal, these are
removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
When printing progress it is useful to print a message and leave the
cursor at the end of the line until the operation is finished. When it is
finished, the line needs to be erased so a new line can start in its place.
Add a function to handle clearing a line previously written by
terminal.Print()
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the board names shown with -l are separated by commas. This
makes it hard to double-click to select a particular board. Also it is not
possible to select all boards and paste them as arguments to a subsequent
buildman run, since buildman requires spaces to separate the list on the
command line, not commas.
Change the output format to use spaces instead of commas.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is quite hard to see the list of board for each error line since the
colour is the same as the actual error line. Show the board list in
magenta so that it is easier to distinguish them.
There is no point in checking the colour of the overall line, since there
are now multiple colours. So drop those tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the string for each error line is created in _CalcErrorDelta()
and used to create the summary output. This is inflexible since all the
information (error/warning character, error line, list of boards with that
error line) is munged together in a string.
Create an object to hold this information and only convert it to a string
when printing the actual output.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present warnings are shown in yellow in the summary (-s) but magenta in
the detail listing (-e). Use yellow in both.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to add a few more tests similar to testOutput(). Split its logic
into a function which runs buildman to get the output and another which
checks the output. This will make it easier to reuse the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having a few tests handle this themselves, create the
temporary directory in the setUp() method and remove it in tearDown().
This will make it easier to add more tests.
Only testOutput and testGit() actually need it, but it doesn't add to the
test time noticeably to do this for all tests in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than using the absolute array index, use an interator to work
through the expected output lines. This is easier to follow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Buildman should output the right colours for each error/warning line. Some
of these checks are missing. Add them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In R-Car Gen 3, there is a DMA controller restriction of SDHI.
When the transfer exceeding the 4 kByte boundary is performed while
the DRAM address is not 128 byte aligned, the bus is occupied.
This patch avoids this.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
When logical address of a regular extent is 0, the extent is sparse and
consists of all zeros.
Without this when sparse extents are used in a file reading fails with
Cannot map logical address 0 to physical
Signed-off-by: Marek Behún <marek.behun@nic.cz>
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
Add the USB DWC2 node to u-boot specific dtsi files since Gadget
support is not (yet) available in upstream Linux yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add arch code to initialize USB Gadget mode using the DWC2 controller,
and using the previously added set_mode() phy functions.
[narmstrong: fixup board_usb_cleanup call to phy_meson_gxl_usb2_set_mode]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add generic_phy_get_by_node() to get a PHY phandle from a node instead
of a udevice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[narmstrong: fixed by including ofnode.h in generic-phy.h]
Add support for backplane kr on t208xqds: remove board specific fixups
on t208xqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
