status and ecc_status are of unsigned type where they are compared for
negative value. This is pointed by below sparse warning. Change datatype
to int to fix this.
warning: comparison of unsigned expression in '< 0' is always false
[-Wtype-limits]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Winbond 256M-bit flash w25q256jwm.
Performed basic erase/write/readback operations on
ZynqMP zc1751+dc1 board.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
XTX changed full company name from "XTX Technology (Shenzhen) Limited
to "XTX Technology Limited" since 2020,So remove "(Shenzhen)".
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The NAND flash controller (NFC) on the AC5/AC5X SoC is the same as
the NFC used on other Marvell SoCs. It does have the additional
restriction of only supporting SDR timing modes up to 3.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move header to include to allow external code
to get the internal bdev structures to access
block device operations.
as at it, just add the UCLASS_NVMXIP string
so we get the correct output in partitions
listing.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
flash_get_size() will get the flash size from the device itself and go
through all erase regions to read protection status. However, the device
mappable region (eg: devicetree reg property) might be lower than the
device full size which means that the above cycle will result in a data
bus exception. This change fixes it by reading the 'addr_size' during
probe() and also use that as one possible upper limit.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
The 'tiny' SPI nor functions have the same name as their big brothers,
which can be confusing. Use different names so it is clear which
version is in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With tiny SPI flash the erasesize is 0 which can cause a divide-by-zero
error. Check for this and return a proper error instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_index_ptr instead of the dev_read_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandisk SDTNQGAMA is a 8GB size, 3.3V 8 bit chip with 16KB page size,
1KB write size and 40 bit ecc support
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
The MTD framework reserves 1 or 2 bytes for the bad block marker
depending on the bus size. The rockchip_nfc driver currently only
supports a 8 bit bus, but reserves standard 2 bytes for the BBM.
The first free OOB byte is therefore OOB2 at offset 2.
Page address(PA) bytes are moved to the last 4 positions before
ECC. Update the description for U-boot.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add flash_node to the rockchip_nfc driver chip structure in order
to find the partitions in the add_mtd_partitions_of() function.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The MTD framework in U-boot is not identical for drivers ported
from Linux. The rockchip_nfc driver was ported with OOB ops functions
while the framework expects a layout structure per chip.
Fix by adding a structure with OOB data and remove unused functions.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The compatible string for rk3308 has as fallback string
"rockchip,rv1108-nfc". As there is no logic in probe priority between
the SoC orientated string and the fall back, so remove the compatible
string "rockchip,rk3308-nfc" from the driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expext 64-bit data from the device tree parser,
so use dev_read_addr_ptr in the rockchip_nfc.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
Add a missing fallthrough macro to avoid a -Wimplicit-fallthrough warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This more closely matches the U-Boot driver to the Linux version.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Michael Trimarchi <micahel@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Clocks, resets, and pinmuxes are now handled by the driver model, so the
only thing the "board" code needs to do is load the driver. This matches
the pattern used by other DM raw NAND drivers (there is no NAND uclass).
The actual board code is now only needed in SPL.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As a first step toward converting this driver to the driver model, use
the ofnode abstraction to replace direct references to the FDT blob.
Using ofnode_read_u32_index removes an extra pair of loops and makes the
allwinner,rb property optional, matching the devicetree binding.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
add nvmxip_qspi driver under UCLASS_NVMXIP
The device associated with this driver is the parent of the blk#<id> device
nvmxip_qspi can be reused by other platforms. If the platform
has custom settings to apply before using the flash, then the platform
can provide its own parent driver belonging to UCLASS_NVMXIP and reuse
nvmxip-blk driver. The custom driver can be implemented like nvmxip_qspi in
addition to the platform custom settings.
Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them.
For more details please refer to doc/develop/driver-model/nvmxip_qspi.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
add block storage emulation for NVM XIP flash devices
Some paltforms such as Corstone-1000 need to see NVM XIP raw flash
as a block storage device with read only capability.
Here NVM flash devices are devices with addressable
memory (e.g: QSPI NOR flash).
The implementation is generic and can be used by different platforms.
Two drivers are provided as follows.
nvmxip-blk :
a generic block driver allowing to read from the XIP flash
nvmxip Uclass driver :
When a device is described in the DT and associated with
UCLASS_NVMXIP, the Uclass creates a block device and binds it with
the nvmxip-blk.
Platforms can use multiple NVM XIP devices at the same time by defining a
DT node for each one of them.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
This patch adds fixups for s25fs512s to address the following issues
from reading SFDP:
- Non-uniform sectors by factory default. The setting needs to be
checked and assign erase hook as needed.
- Page size is wrongly advertised in SFDP.
- READ_1_1_2 (3Bh/3Ch), READ_1_1_4 (6Bh/6Ch), and PP_1_1_4 (32h/34h)
are not supported.
- Bank Address Register (BAR) is not supported.
In addition, volatile version of Quad Enable is used for safety.
Based on patch by Takahiro Kuwano with s25fs_s_post_bfpt_fixup() updated
to use 4-byte address commands instead of extended address mode and the
page_size is fixed to 256
For future use, manufacturer code should be moved out from framework
code as same as in Linux.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a missing fallthrough macro to avoid a -Wimplicit-fallthrough warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for CHIP_ERASE opcode 0xc7 . This is useful in case the
entire SPI NOR is supposed to be erase at once, as is it considerably
faster than 4k sector erase and even slightly faster than 64k block
erase. The spi_nor_erase_chip() implementation is adapted from Linux
6.1.y as of commit 7d54cb2c26dad ("Linux 6.1.14") . The chip erase is
only used in case the entire MTD device is being erased, and the chip
does support this functionality.
Timing figures from W25Q128JW:
16 MiB erase using 4kiB sector erase opcode 0x20 ... 107.5s
16 MiB erase using 64kiB block erase opcode 0xd8 ... 39.1s
16 MiB erase using chip erase opcode 0xc7 .......... 38.7s
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----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=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
nand-ecc-algo = "bch";
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm]
Link: https://lore.kernel.org/all/20230407134008.1939717-3-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
It will be replaced by a more recent version which contains fixes for
tests run by Tom Rini.
This reverts commit ff33d3c87c.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Remove the EDO mode support from as the FMC2 controller does not
support the feature.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
octeontx_bch_devices and octeontx_pci_nand_deferred_devices are only
referenced in the files where they are defined. Make them static.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230405143837.785082-1-bmeng@tinylab.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add support for the iproc Broadcom NAND controller,
used in Northstar SoCs for example. Based on the Linux
driver.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308214231.378013-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
For BRCMNAND with 1-bit BCH ECC (BCH-1) such as used on the
D-Link DIR-885L and DIR-890L routers, we need to explicitly
select the ECC like this in the device tree:
nand-ecc-algo = "bch";
nand-ecc-strength = <1>;
nand-ecc-step-size = <512>;
This is handled by the Linux kernel but U-Boot core does
not respect this. Fix it up by parsing the algorithm and
preserve the behaviour using this property to select
software BCH as far as possible.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308212851.370939-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Ofnode value is not set, so all the DT properties are not being read
and due to this default values are being used.
Find nand node and set chip->flash_node value.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Bad block table option is hardcoded to read from flash with
NAND_BBT_USE_FLASH option. This decision should be done based on DT
property. Remove this hardcoding, to be able to use DT property.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This is not used since time out of mind.
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Add a new Kconfig option CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND which instruct
make to generate kwbimage with NAND header. This image is used for booting
from NAND flash (either SPI or parallel).
Support is very simple, SPL after finishes DDR training returns back to the
BootROM (via CONFIG_SPL_BOOTROM_SUPPORT option) and BootROM then loads and
executes U-Boot proper.
To generate correct kwbimage NAND header, it is required to set following
Kconfig options:
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION
They are used only by make / mkimage when generating final kwbimage.
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION is a new mvebu specific Kconfig
option which is set into kwbimage NAND_BADBLK_LOCATION header field.
Signed-off-by: Pali Rohár <pali@kernel.org>
The "nand chip.erase" command always printed as bad blocks even in the
case of reserved blocks. Reserved blocks are used for storing bad block
tables. The patch displays "bbt reserved" when printing reserved blocks in
"nand chip.erase" command.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In case ID is not found in manufacturer table, the raw ID is
printed using %*phN format which is not supported by lib/vsprintf.c.
The information displayed doesn't reflect the raw ID return by the
unknown spi-nand.
Use %02x format instead, as done in spi-nor-core.c.
For example, before this patch:
ERROR: spi-nand: spi_nand flash@0: unknown raw ID f74ec040
after
ERROR: spi-nand: spi_nand flash@0: unknown raw ID 00 c2 26 03
Fixes: 0a6d6bae03 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
