This patch fixes not enabled uart2 (and hence serial console) on i.MX53
devices. After following commit 1d255904c3 ("ARM: dts: imx: imx53:
Synchronize iMX53 DT with Linux") from the uart2 compatible the
'fsl,imx7d-uart' has been removed (which was correct).
However, the root cause of the problem was the commit 98d62e618b ("arm:
imx: add i.MX53 Beckhoff CX9020 Embedded PC") which introduced this
compatible.
Moreover, without this patch all i.MX53 UARTs are not usable as neither
'fsl,imx53-uart' nor 'fsl,imx21-uart' are in compatible IDs in
drivers/serial/serial_mxc.c file.
The fix is to add 'fsl,imx53-uart' and 'fsl,imx21-uart' as compatibles
for the aforementioned serial driver (those are also defined in the Linux
kernel).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The DM_FLAG_PRE_RELOC shall be set unconditionally as this driver is going
to be re-used in both early SPL and U-Boot proper's pre-reloc.
For i.MX based devices it is crucial to have available the serial console
before relocation (otherwise the board may hand).
The device definition may be provided either via device tree description or
with U_BOOT_DEVICE(mxc_serial) definition. In the latter case the device
will not bind in U-Boot proper when DM_FLAG_PRE_RELOC is not set.
The !CONFIG_IS_ENABLED(OF_CONTROL) #if check was set as a "workaround" for
DM problem described in following commit 4687919684
("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers").
Let's look on this check more thoroughly - we add this flag if the board
doesn't support OF_CONTROL. This is a bit strange as the serial_mxc.c can
be used with CONFIG_DM_SERIAL but without corresponding device tree
description (OF_CONTROL). In such case the aforementioned
U_BOOT_DEVICE(mxc_serial) definition is used.
Other boards/SoCs have this flag set unconditionally for serial driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch solves the following warnings:
drivers/serial/serial_stm32.c: In function 'stm32_serial_probe':
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (plat->clock_rate < 0) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
By default LPUART driver with compatible string "fsl,ls1021a-lpuart"
support big-endian mode.On NXP SoC like LS1028A LPUART IP is
little-endian,Added support to Fetch LPUART IP Endianness from lpuart
device-tree node.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=meeB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190523' of https://github.com/pchotard/u-boot
- Add various STM32MP1 fixes for serial, env, clk, board, i2c ...
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
This patch adds devicetree support to the mcfuart.c driver
and removes non DM code.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
For STM32MP, the watchdog is based on DM and the function watchod_reset
call the function uclass_get_device(UCLASS_WDT) to found the driver
associated IWDG2.
As this reset is not mandatory in debug putc (the uart fifo will be
empty after some us), we can simplify the code by removing this call.
And this patch avoid issue when putc is called before initialization
of DM core, before the parsing of the device tree parsing and each
node bound to driver; that also avoid memory leak.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Convert 'altera_uart_ofdata_to_platdata' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int' and get rid of DECLARE_GLOBAL_DATA_PTR.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This CPU core is old, no boards using the CPU are left in mainline,
it has no prospects of ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
This CPU core is old, no boards using the CPU are left in mainline,
it has no prospects of ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Drop unused macros from the header to clean it up.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no RTS7751R2D support in U-Boot, drop all the RTS7751R2D macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no SH2007 support in U-Boot, drop all the SH2007 macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no H8 support in U-Boot, drop all the H8 macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the serial_sifive driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/serial/serial_sifive.c:6:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in serial_sifive.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for RZ/A1 SoC specifics.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are no more boards using this CPU and there is no prospect
of any boards showing up soon, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
There are no more boards using this CPU and there is no prospect
of any boards showing up soon, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds an alterative SPL version of atmel_serial_enable_clk().
This enables the usage of this driver without full clock support (in
drivers and DT nodes). This saves some space in the SPL image.
Please note that this fixed clock support is only added to the SPL code
in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL
should not be affected.
This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART
input clock. It defaults to 132096000 for ARCH_AT91 but can be set to
a different value if needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Kconfig allows boards to configured with DM_SERIAL and still
have SPL_DM_SERIAL disabled. This patch changes the ifdef's
to CONFIG_IS_ENABLED to allow the modes to differ between
SPL and U-Boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible that input clock is not available because clk
device was not available and 'clock-frequency' DT property is
also not available.
In this case, instead of failing we should just skip baudrate
config by returning zero.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The DM_FLAG_PRE_RELOC shall be enabled in SBSA PL011 uart driver
as this driver is used in NXP based SoCs
It is necessary to have Serial console running before relocation
The !CONFIG_IS_ENABLED(OF_CONTROL) [*] check is set as "workaround"
for DM problem : 4687919684
This flag is set if board does not support device-tree and using
platform data, In DM Model either of device tree or platform data
can be used to fetch device configuration
It is possible to use SBSA UART with CONFIG_DM_SERIAL but witout
corresponding device tree description (OF_CONTROL)
Other board/SoCs have this flag set unconditionally
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Apparently we never allocated buffer for arc_serial_platdata
which for some reason never caused problems when executed in nSIM.
But in Qemu this causes expected problems.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlw+AlIACgkQfxc6PpAI
reYchAf+L/P5JsLoCKAY84v11eWQkCS44idAYStD8Q023dyuyNC/W6G3qEQVGkHu
SXBzNrZ5wSJanN5I3h3ktJ7yfMOYIvSO2qLHphxDstPaZbCY4Zac6NywHrHxQpA9
fbSilQRbcVWrPo5rsjjZhXmMdQRZVOmGD6CYZj1AihWAiHfYth7f6laNWNTWQA8C
z+aoiF70t/PbvwFbgdzzYOjoGdXI9XML0xTqdLWRlsBKjf3z54pCV6LmN2xrsrDZ
k7lr+x7ajJUFhivxzjowf4aOjhDB+/+I3sr+hJ5vkMM0Kqg14bbEU+xJRGpDc18K
QPvVHT5JGe/nq1cZXuCqzrYxTrrA7A==
=w9ln
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15jan19' of git://git.denx.de/u-boot-dm
Fix recent changes to serial API for driver model
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
If _debug_uart_putc() is called before _debug_uart_init(), the
ns16550 debug uart driver hangs in a tight loop waiting for the
tx FIFO to get empty.
As this can happen via a printf sneaking in before the port calls
debug_uart_init(), introduce a config option to ignore characters
before the debug uart is initialized.
This is done by reading the baudrate divisor and aborting if is zero.
The Kconfig option is required as reading the baudrate divisor does
not seem to work for all ns16500 compatibles (which is why the last
attempt on this has been reverted in 1a67969a99).
Tested on socfpga_cyclone5_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DEBUG_UART_SKIP_INIT is used only by debug UART and thus should depend
on DEBUG_UART.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
All driver-model functions should have a device as the first parameter.
Update this function accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This patch adds SiFive UART driver. The driver is 100% DM driver
and it determines input clock using clk framework.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
In some cases, UART is configured by early boot stage.
To be sure of the initial state of UART and to avoid
spurious chars on console, reset the serial block before
configuring it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds code missing when CONFIG_DEBUG_UART_OMAP is enabled as
early debugging UART. The code is basically copied from the ns16550
driver.
Signed-off-by: Felix Brack <fb@ltec.ch>
New callback will supply necessary information, for example,
to ACPI SPCR table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cache the value of the reg-io-width property for the future use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
New callback will give a necessary information to fill up ACPI SPCR table,
for example. Maybe used later for other purposes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change ADR_SPACE_SYSTEM_IO to SERIAL_ADDRESS_SPACE_IO to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it would be good to know the settings, such as parity,
of current serial console. One example might be an ACPI SPCR table
to generate using these parameters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 6f57c34473 since it
does not seem to work at least on rk3399.
The Rockchip Technical Reference Manual (TRM) for the rk3399 says the baud
rate prescaler register is readable only when USR[0] is zero. Since this
bit is defined as "reserved" in the socfpga cylcone5 TRM, let's rather
drop this than making the ns16550 debug uart more platform specific.
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com
