The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add xspi boot source to qixis command to let the soc boot from
flex-nor flash chip.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Remove "fdt_high" environment variable to use the bootm_size
to safely contain a kernel, device tree and initrd for
relocation.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On aarch64 running with dcache off, will result in an unaligned access
exception:
=> dcache off
=> hash sha1 $kernel_addr_r 100
"Synchronous Abort" handler, esr 0x96000061
elr: 00000000960317d8 lr : 00000000960316a4 (reloc)
elr: 00000000fbd787d8 lr : 00000000fbd786a4
[..]
The compiler emits a "stur x1, [x0, #12]". x1 is might just be 32 bit
aligned pointer. Remove the unused u64 element from the union to drop
the minimal alignment to 32 bit. Also remove the union, because it is
no more needed.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This enables SYS_I2C_MXC to fix a bug that
failed to boot from sd card with
image u-boot-with-spl-pbl.bin
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two issues:
(1) The spin table doesn't convert the endianness of the jump address.
Although there is code for it, the result isn't used at all (x0).
(2) If something goes wrong, the function returns. But that doesn't
make sense at all.
Use the actual converted jump address as destination to fix. If
there is an error, jump to a trap loop. And rearrange the code exception
level switching code to make it smaller and clearer.
This reduces the size of the spin table code section from 696 bytes to
424 bytes. If CONFIG_ARMV8_SWITCH_TO_EL1 the code size reduced from 696
bytes to 632 bytes.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On ARM64, a 64kb region is reserved for the runtime services code.
Unfortunately, this code overlaps with the spin table code, which also
needs to be reserved. Thus now that the code is relocatable, allocate a
new page from EFI, copy the spin table code into it, update any pointers
to the old region and the start the secondary CPUs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a new variable secondary_boot_code_start, which holds a pointer to
the start of the spin table code. This will help to relocate the code
section. While at it, move the size variable from the end to the
beginning so there is a common section for the variables. Remove any
other symbols.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the spin table is in a separate module, this is no longer
necessary. Drop it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This function is not used outside the module. Make it static.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no need to cast around. Assign the address to the local
variable and use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Only the PowerPC architecture needs this function. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix the alignment so it will match the comments. The spin table has to
be 8 byte aligned, so ".align 3" is enough.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Don't use LDR to load a pointer to a function. This will generate a
literal which cannot be relocated. Use ADR which is PC-relative and
therefore can easily be relocated.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move it out of lowlevel.S into spintable.S. On layerscape, the secondary
CPUs are brought up in main u-boot. This will make it possible to only
compile the spin table code for the main u-boot and omit it in SPL.
This saves about 720 bytes in the SPL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The generic armv8 code already has support to bring up the secondary
cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to
the spin table code; instead just return early and let the common armv8
code handle the jump. This way we can actually use the CPU_RELEASE_ADDR
feature.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased, Removed kontron_sl28.h change as file does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Make the print of the starting address a debug output and pretty print
the info about online cores.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Spin tables are broken with bootefi. This is because - in contrast to
the booti call chain - there is no call to smp_kick_all_cpus(). Due to
this missing call the secondary CPUs are never released from their "wait
for interrupt state", see secondary_boot_func() in lowlevel.S.
Originally, this "wait for interrupt" is there to make sure, the spin
table is cleared before the secondary cores read it for the first time.
But the boot flow for the layerscape architecture is different from
that. The CPUs are release from their BootROM _after_ U-Boot's
spin-table is cleared, see fsl_layerscape_wake_seconday_cores() in mp.c.
Thus, there is no need to wait for this interrupt and no need for
kicking all cores on cpu_release. An atomic 64bit write to the
spin-table and a "sev" is sufficient.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current PFE firmware access spi-nor memory directly. New spi-mem
framework does not support direct memory access. So, let's use
spi_flash_read API to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1088A-RDB has MMC, SCSI, DHCP as boot targets,
but the USB support was missing.
Add support for USB as Boot_targets_devices.
Signed-off-by: Era Tiwari <era.tiwari@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to
define it per board; the ls1028a_common.h is really board dependent and
only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE
when ARCH_LS1028A is selected.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Communication with some SPI slaves just won't cut it if these delays
(before the beginning, and after the end of a transfer) are not added to
the Chip Select signal.
These are a straight copy from Linux:
Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
drivers/spi/spi-fsl-dspi.c
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
With the change to absolute imports the concurrent tests feature
unfortunately broke. Fix it.
We cannot easy add a warning, since the output messes up tests which check
the output.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present testPackX86RomMeNoDesc removes the contents of the
descriptor.bin file and testPackX86RomMeMissingDesc removes the file
completely.
If a test that relies on this file happens to run after it is removed, it
will not work. Since we have no control over the selecting of tests that
run in parallel and series, we must avoid changing the files.
Update this tests to use separate files instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Manage 2 copy at the end of the partition selected by config
"u-boot,mmc-env-partition" to save the U-Boot environment,
with CONFIG_ENV_SIZE and 2*CONFIG_ENV_SIZE offset.
This patch allows to support redundancy (CONFIG_ENV_OFFSET_REDUND).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The output of the function mmc_offset_try_partition must be a
byte offset in mmc and not a multiple of blksz.
This function is used in mmc_offset(), called by mmc_get_env_addr()
and the offset is used in write_env(), erase_env() and read_env().
In these function, blk_start = offset / mmc->read_bl_len
or /write_bl_len so this offset is not a multiple of blksz.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the weak function mmc_get_env_dev in mmc_offset_try_partition
function to allow dynamic selection of mmc device to use
and no more use directly the define CONFIG_SYS_MMC_ENV_DEV.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a pytest for testing the env info sub-command:
test_env_info: test command with several option that
can be executed on real hardware device without assumption
test_env_info_sandbox: test the result on sandbox
with a known ENV configuration: ready & default & persistent
The quiet option '-q' is used for support in shell test;
for example:
if env info -p -d -q; then env save; fi
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Enable support for sub command 'env info' in sandbox
with CONFIG_CMD_NVEDIT_INFO. This is aimed primarily
at adding unit test.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check the current ENV location, dynamically provided by the weak
function env_get_location to be sure that the environment can be
persistent.
The compilation flag ENV_IS_IN_DEVICE is not enough when the board
dynamically select the available storage location (according boot
device for example).
This patch solves issue for stm32mp1 platform, when the boot device
is USB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The "env info" can be use for test with -d and -p parameter,
in scripting case the output of the command is not needed.
This patch allows to deactivate this output with a new option "-q".
For example, we can save the environment if default
environment is used and persistent storage is managed with:
if env info -p -d -q; then env save; fi
Without the quiet option, I have the unnecessary traces
First boot:
Default environment is used
Environment can be persisted
Saving Environment to EXT4... File System is consistent
Next boot:
Environment was loaded from persistent storage
Environment can be persisted
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add trace in env save to indicate any errors to end user and avoid
silent output when the command 'env save' is not executed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Correct the overflow check of the bit-field env_has_init with
the max value of env_location= ENVL_COUNT and no more with the
size of env_locations.
This bit-field is indexed by this enumerate and not by the position in
the env_locations (only used in env_get_location) and the
2 values are different, depending of thea ctivated CONFIG_ENV_IS_ options.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
I don't want to have to specify the device; only the partition.
This allows me to use the same image on internal eMMC or SD card for
Banana Pi R2, and it finds its own environment either way.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage,
whitespace changes]
Signed-off-by: Tom Rini <trini@konsulko.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, fdt_fixup_mtdparts() only checks the compatible property.
It is pointless to fix up the disabled node.
Skip the node if it has the property:
status = "disabled"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Platform code can call fdt_fixup_mtdparts() in order to hand U-Boot's
MTD partitions over to the Linux device tree.
Currently, fdt_fixup_mtdparts() calls mtdparts_init() in its entry.
If no target MTD device is found, an error message like follows is
displayed:
Device nand0 not found!
This occurs when the same code (e.g. arch/arm/mach-uniphier/fdt-fixup.c)
is shared among several boards, but not all of them support an MTD device.
Parse the DT first, then call mtdparts_init() only when the target MTD
node is found.
Yet, you still need to call mtdparts_init() before device_find().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Running 'ut dm' on the sandbox without -D or -d results in segmentation
faults due to NULL pointer dereferences.
Check that device pointers are non-NULL before using them.
Use ut_assertnonnull() for pointers instead of ut_assert().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
