By default, i2c input clock is programmed at
platform clk / 2 in u-boot, but this is not
correct for all the platforms,
Update I2C clock divider's default values as per
SoC (LS1012A, LS1028A, LX2160A and LS1088A).
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SP805-WDT module on LS1028A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the device-tree structure describing the MUX in board dts.
QDS board has an on-board RGMII PHY and 4 slots for extension cards.
All these can be accessed over MDIO through a MDIO MUX controlled
over I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
During boot, u-boot reads MC, DPL, DPC firmware from SD card
and copies to DDR. Update DDR addresses to which these firmwares
are copied as per memory map of these firmwares on SD-card
so that isolation between the regions of various firmwares
is maintained to avoid geting overwritten.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add eMMC hs200 mode for ls1028a, ls1012a, lx2160a.
This increases eMMC performance.
Tuning procedure is currently not supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
NXP fsl_esdhc controller supports two reference clocks:
platform clock and peripheral clock
Peripheral clock can provide higher clock frequency
which is required to be used for tuning of SD UHS mode
and eMMC HS200/HS400 modes.
Peripheral clock is enabled by default by defining config
option FSL_ESDHC_USE_PERIPHERAL_CLK if eMMC HS200/HS400 modes
are supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- add idbloader.img target for rockchip tpl+spl;
- usb ehci/ohci: go on process if clock driver don't have clk_enable();
- remove clk_enable() for rockchip clock drivers;
- add boot order for rockpro64
We do not support volume label changes. No parameter checks are needed
here.
When the info for as file is changed the buffer must always contain a file
name.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Many Rockchip platforms require the same u-boot deploy procedure
when TPL and SPL both enabled.
The following examples are taken from doc/README.rockchip
and board/theobroma-systems/lion_rk3368/README:
RK3288:
./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out
cat ./spl/u-boot-spl-dtb.bin >> out
sudo dd if=out of=/dev/mmcblk0 seek=64
RK3328:
./tools/mkimage -n rk3328 -T rksd -d ./tpl/u-boot-tpl.bin idbloader.img
cat ./spl/u-boot-spl.bin >> idbloader.img
sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64
RK3368:
./tools/mkimage -n rk3368 -T rksd -d tpl/u-boot-tpl.bin spl-3368.img
cat spl/u-boot-spl-dtb.bin >> spl-3368.img
dd if=spl-3368.img of=/dev/sdb seek=64
RK3399:
./tools/mkimage -n rk3399 -T rksd -d ./tpl/u-boot-tpl-dtb.bin out
cat ./spl/u-boot-spl-dtb.bin >> out
sudo dd if=out of=/dev/sdc seek=64
Here, we introduce generic idbloader.img target
which is the TPL image followed by the SPL binary.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use obj-$(config) instead of #ifdef $config to make the code looks
clean, and move the misc_init for U-Boot proper only.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3188/Makefile already depends on !TPL_BUILD, so no need to add
this again in parent Makefile, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There is no real driver for clk enable/disable now, and we actually
don't need it now, remove it so that not waste CPU cycles and code size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There is no real driver for clk enable/disable now, and we actually
don't need it now, remove it so that not waste CPU cycles and code size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There is no real driver for clk enable/disable now, and we actually
don't need it now, remove it so that not waste CPU cycles and code size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There is no real driver for clk enable/disable now, and we actually
don't need it now, remove it so that not waste CPU cycles and code size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
commit 65c1f9820c8f79f "usb: Add nonblock argument to submit_int_msg"
breaks the musb_hcd driver.
Fixing it by adding the missing argument
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
An USB 1.1 keyboard connected to dwc2 through a high-speed hub does not
report status until it changes. With this patch you can enable keyboard
by pressing a key while USB devices are probed. Without a keypress no
state is reported and the probe times out. We don't want to wait for a
keypress or timeout while polling for keypresses so implement an int_msg
nonblock variant that exits early on error.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
- Tangier ACPI table fixes
- Support getting high memory size on QEMU x86
- Show UEFI images involved in crash for x86
- EFI loader conventional memory map fix
a device is plugged only in the OTG capable port for libretech-ac and libretech-cc
-----BEGIN PGP SIGNATURE-----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=C5op
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190910' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Add support for dis_u2_susphy_quirk in the xhci-dwc3 driver to fix boot when
a device is plugged only in the OTG capable port for libretech-ac and libretech-cc
For sake of consistency use spaces over TABs in ASL code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel iDMA 32-bit controller has 17 bits for the maximum block size value.
Due to nature of the binary number representation the maximum value is
2^17 - 1. The original code misses the latter part in equation.
Fixes: 5e99fde34a ("x86: tangier: Populate CSRT for shared DMA controller")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per PCI firmware specification the ACPI has to reserve the memory
which is defined as PCI ECAM.
Fixes: 39665beed6 ("x86: tangier: Enable ACPI support for Intel Tangier")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GCC 9.2 starts complaining about possible pointer misalignment of
pointers to the unpacked (alignment=4) structures in the packed
(alignment=1) ones:
CC arch/x86/cpu/tangier/acpi.o
arch/x86/cpu/tangier/acpi.c: In function ‘acpi_create_fadt’:
arch/x86/cpu/tangier/acpi.c:22:37: warning: taking address of packed
member of ‘struct acpi_fadt’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
22 | struct acpi_table_header *header = &(fadt->header);
CC arch/x86/lib/acpi_table.o
arch/x86/lib/acpi_table.c: In function ‘acpi_create_spcr’:
arch/x86/lib/acpi_table.c:366:37: warning: taking address of packed
member of ‘struct acpi_spcr’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
366 | struct acpi_table_header *header = &(spcr->header);
Fix the potential issues by annotating embedded structures with
__packed even though they are packed naturally.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add GCC version number in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This quirk is necessary for the Amlogic GXL SoCs otherwise the
Port 2 PHY doesn't get out of suspend and U-Boot resets the board after:
XHCI timeout on event type 33... cannot recover.
BUG: failure at drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
This quirk is also handled in the dwc3 core code, but until the
xhci-dwc3 driver uses the dwc3 core, the quirk must be handled here
to fix USB support on the Amlogic libretech-cc and libretech-ac board
when a device is only plugged in the OTG port.
Cc: Yuri Frolov <crashing.kernel@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fixes: dc9cdf859e ("usb: dwc3: Add DWC3 controller driver support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use efi_add_conventional_memory_map() to configure EFI conventional memory
properly with ram_top value. This will give 32-bit mode U-Boot proper
conventional memory regions even if e820 has an entry which is greater than
32-bit address space.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[bmeng: fixed some typos in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a crash occurs, show the loaded UEFI images to facilitate analysis.
This is an example output:
=> bootefi 0x1000000
Found 0 disks
Hello world of bugs!
Invalid Opcode (Undefined Opcode)
EIP: 0010:[<06ceb06e>] EFLAGS: 00010206
Original EIP :[<fec9906e>]
EAX: 00000000 EBX: 06cec000 ECX: 00000fd0 EDX: 00000001
ESI: 06ced18a EDI: 07d0fe10 EBP: 07fe27a0 ESP: 07d0fde0
DS: 0018 ES: 0018 FS: 0020 GS: 0018 SS: 0018
CR0: 00000033 CR2: 00000000 CR3: 00000000 CR4: 00000000
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Stack:
0x07d0fde8 : 0x00000000
0x07d0fde4 : 0x06ced040
--->0x07d0fde0 : 0x07fe27a0
0x07d0fddc : 0x00010206
0x07d0fdd8 : 0x00000010
0x07d0fdd4 : 0x06ceb06e
UEFI image [0x06cea000:0x06cf0fff] pc=0x106e '/bug-i386.efi'
### ERROR ### Please RESET the board ###
With the additional information provided by this patch we know that the
problem occurred 0x106e after the load address of bug-i386.efi.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add steps to test Linux booting on QEMU with Yocto image.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that we are able to get the size of high memory from QEMU,
report its memory range as usable ram.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
At present only size of memory that is below 4GiB is retrieved from
QEMU. Add a function that gets size of memory that is above 4GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
This extracts getting memory size logic in dram_init() to a separate
routine qemu_get_low_memory_size(). No functional changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Every x86 platform provides board_get_usable_ram_top(), hence there
is no need to provide a weak version board_get_usable_ram_top(), not
to mention there is another weak version board_get_usable_ram_top()
in common/board_f.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Using ACPI predefined macros, such as Zero or One, will reduce a binary
size of resulting ACPI tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: manually fixed the conflicts when applying]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Follow up fix to the commit
56bf4f8630 ("x86: Add ifwitool for Intel Integrated Firmware Image")
in order to ignore created binary.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While the original patch to fix a regression in distro boot for mmc on
these platforms had the correct syntax, I broke the change while
applying. Add back in the missing "=" here so that the syntax is
correct.
Reported-by: Andre Heider <a.heider@gmail.com>
Fixes: 27e0f3bcf0 ("arm: ti: Fix regression in distro boot for mmc")
Signed-off-by: Tom Rini <trini@konsulko.com>
Check the parameters of EFI_FILE_PROTOCOL.GetInfo() to avoid possible NULL
dereference.
Check the buffer size for EFI_FILE_SYSTEM_INFO.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
