Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that most rockchip SoC based board have usb host support, enable
USB boot targets by default.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build errors when CONFIG_CMD_USB not defined:
Signed-off-by: Simon Glass <sjg@chromium.org>
tinker board support ethernet and usb host, so enable USB, PXE and DHCP support.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Fix build error with sama5d3_xplained_mmc:
Signed-off-by: Simon Glass <sjg@chromium.org>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Remove CONFIG_PHY_MICREL as per previous patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add back CONFIG_PHY_MICREL to prevent a build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
This removes the default environment from the sr1500 header
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board has no upstream devicetree in the kernel source,
so set to socfpga_cyclone5_sr1500.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
This removes the default environment from the socrates headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This removes the default environment from the SoCKit headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This removes the default environment from the de1 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board does not have a devicetree in the upstream kernel
source so set devicetree to socfpga_cyclone5_de1_soc.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in V2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
This removes the default environment from the C5 SoCDK headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This removes the default environment from the A5 socdk headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Add support to boot from the custom a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v3:
- Fix small typo in defconfig, missing "C"
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- Fix dtb name
a5config test
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
This removes the default environment from the de0 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This adds a common environment and support for distro boot
in the common socfpga header.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v5:
- Per Frank, to support OpenSuse the ENV must be after the GPT
Changes in v4:
- Move env back to being right after the MBR
Changes in v3:
- fix spacing between asterix
- remove verify=n as a default setting
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE and fdt_addr
- cleanup spacing in MMC env size
common
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
There is no point in having such gargantuan buffer, it only requires
huge malloc area. Reduce the DFU buffer size.
Signed-off-by: Marek Vasut <marex@denx.de>
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add #ifndef CONFIG_DM_GPIO for CONFIG_AT91_GPIO define to avoid
the redefine compilation error.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Instead of having CONFIG_SANDBOX_BITS_PER_LONG in sandbox.h set to 64
with a comment to change to 32 on a 32bit host, simply set this to 64 in
asm/types.h and have the comment be there.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
By default, u-boot itself outputs on the serial console at 115200, so
it may as well pass the same value to the booted operating system as
well.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add the configuration options for display initialization in case we need to
do the display initialization in kernel to support different timing settings
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
There is option which is not used:
CONFIG_ZBOOT_32
Remove it from default x86 config and from whitelist.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The most common name for a FIT image containing a bootable kernel is
"fitImage", as our builds now use this name also, change this to the
default in our U-Boot environment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Now that we have common MMC/SD boot environment
variables that can be used across TI platforms,
switch OMAP-L138 LCDK to use them.
As a nice side-effect, we get support for using
uEnv.txt on this platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce include/environment/ti/mmc.h that
consolidates environment variable definitions
for various TI boards that support MMC/SD.
This allows reuse of same environment variables
on non-ARMv7 TI platforms like OMAP-L138 for
example.
While at it, move DFU-related environment variable
includes to only non-SPL builds for AM335x and
AM437x since they are not really used for SPL
today.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use environment variables for various memory addresses
used on OMAP-L138 LCDK board. This makes it easy to
customize the boot process.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
OMAP-L138 LCDK board does not have a SPI flash.
Remove spiboot related environment variable
definitions.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing
on robotics with a TI wl1835 wireless module for connectivity.
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/bluehttps://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
http://beagleboard.org/green-wirelesshttp://wiki.seeed.cc/BeagleBone_Green_Wireless/
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
http://beagleboard.org/black-wirelesshttps://github.com/beagleboard/beaglebone-black-wireless
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
It also enables commands for cache enable/disable/status.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
The env command 'args_fit' does not define a root path, this forces us to
embed the rootfs into the FIT image. FIT images do not need to contain a
rootfs, when they do not the kernel will fall-back to the kernel argument
'root', if this is not defined the kernel will not boot. It is safe to
add this as when we do have the rootfs in FIT this argument is ignored.
As 'loadfit' is only called from the MMC boot path, use 'args_mmc' to
correctly populate 'bootargs'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
SPI U-Boot image for K2 boards have now exceeded 512K partition
allocated to it and no longer fit the partitions defined in kernel DTS
file. Therefore, pass an updated MTD partition table from U-Boot as
kernel command line arguments to avoid kernel from accidentally
modifying boot loader image that has overflowed to next user partition.
To do is, introduce a common environment file for declaring SPI
partition so that each individual boards need not repeat the same.
Choose appropriate SPI bus from board config file and pass it as command
line argument to kernel.
Signed-off-by: Vignesh R <vigneshr@ti.com>
On boards that defines ENV_IS_NOWHERE, such as the NES classic, commit
19dbe7d1a3f7 ("common: Move environment choice to Kconfig") broke the build
because of a missing environment size.
Reintroduce a default environment size consistent with what we had before.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order for the user to be able to see and modify them, add those
variables to the default environment.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Enable the NAND and UBI support in the configuration header so that we can
(finally) use it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The environment location is something that might change per board
(depending on what storage options are availaible there) or depending on
the user choice (when we have several options).
Instead of hardcoding it in our configuration header, create a Kconfig
choice with the options we use for now, and the symbols that depend on it.
Once done, also remove the irrelevant sunxi defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The OpenRISC architecture is currently unmaintained, remove.
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When this board was switched to using more DM drivers we didn't disable
the legacy PCA953X driver. This in turn learn to a build time warning
about implicit functions as i2c.h would not say anything about
'i2c_read' nor 'i2c_write'. But this was not a fatal error as none of
the legacy driver would be linked in either.
Fixes: e389033f72 ("imx: mx6sxsabreauto: enable more dm drivers")
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For some reason we were pretty conservative when defining the maximum
SPL size for the Allwinner A80(sun9i) SoC.
According to the manual the SRAM A1 is even 40KB, but the BROM
probably still has the 32 KiB load limit. For the sake of simplicity,
merge the SPL memory definitions for the A64 and A80 SoCs, since both
SoC share the BROM/SRAM A1 memory layout.
This helps to further simplify this is in the next patch.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the baseline defconfig for the RK3399-Q7 (Puma) SoM
(under the name 'puma-rk3399_defconfig') featuring the Rockchip RK3399
in a Qseven compatible module.
This subsumes the following changes:
* defconfig: rk3399: migrate CONFIG_SPL_LIBCOMMON_SUPPORT/CONFIG_SPL_LIBGENERIC_SUPPORT
* defconfig: rk3399-puma: add CONFIG_MMC_DW_ROCKCHIP
* defconfig: rk3399-puma: disable CONFIG_SPL_OF_PLATDATA
* defconfig: rk3399-puma: don't USE_TINY_PRINTF
* defconfig: rk3399-puma: set up CONFIG_SYS_BOARD for the RK3399-Q7
* defconfig: rk3399-puma: enable the multi-image loading via CONFIG_SPL_FIT
* defconfig: rk3399-puma: SPL should be able to boot from MMC/SD card
* defconfig: rk3399-puma: enable GMAC support
* defconfig: rk3399-puma: enable support for SPI and Winbond SPI flash
* defconfig: rk3399-puma: enable SPI as a boot-source in SPL
* defconfig: rk3399-puma: disallow non-FIT images from being loaded
* defconfig: rk3399-puma: rename to puma-rk3399
* rockchip: config: rk3399: update defconfigs and rk3399_common
For the RK3399-Q7, we want a default boot-order of SPI -> MMC -> uSD.
This both follows how the BootROM probes devices and is a sane default
for customers in device-personalisation (e.g. it allows for quick and
easy factory programming of unpersonalised devices using an SD card)
and field usage (with customer devices expected to have their firmware
either in SPI or MMC).
However, when probing multiple interfaces (according to the result
from the board_boot_order function), we need to ensure that only valid
FIT images are considered and disable the fallback to assuming that a
raw (binary-only) U-Boot image is loaded (to avoid hangs/crashes from
jumping to random content loaded from devices that are probed, but
don't contain valid image content).
By disabling the SPL_RAW_IMAGE_SUPPORT and SPL_LEGACY_IMAGE_SUPPORT
options, we ensure that raw images (indistinguishable from random
data) are not considered for booting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop CONFIG_DEBUG_UART_BOARD_INIT:
Signed-off-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7 we need to enable a number of configuration options
(e.g. CONFIG_SPI_FLASH_WINBND) dependent on Kconfig seeing CONFIG_SPI
and CONFIG_SPI_FLASH active.
To allow for these being defined in Kconfig (e.g. via defconfig) and
to avoid a warning on having the macro defined multiple times, we
remove them from the common header file.
Note that the rk3399-evb does not currently have the rk_spi.c driver
active (i.e. CONFIG_ROCKCHIP_SPI), so there's no change to the
evb-rk3399_defconfig as part of this change.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Rock is a RK3188 based single board computer by Radxa.
Currently it still relies on the proprietary DDR init and
cannot use the generic SPL, but at least is able to boot
a linux kernel and system up to a regular login prompt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix sort order in defconfig, enable CONFIG_SPL_TINY_MEMSET:
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 3a649407a4 ("arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce
SPL_SYS_THUMB_BUILD") moved the THUMB_BUILD symbols from the header to
Kconfig symbols. With it still defined in the rk3188 header we end up
with a duplicate symbol and compile errors, so fix that.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The BootROM of the RK3399 SoC does not initialise the cntfrq_el0 (which
holds the value 0 (zero) on entry into the SPL. This causes the timebase
for U-Boot not to advance (and will cause a hang where a timeout would
be expected... e.g. if something goes wrong during MMC/SD card startup).
This change defines COUNTER_FREQUENCY, which is used by the AArch64 init
code in arch/arm/cpu/armv8/start.S to set up cntfrq_el0 (if necessary).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.
This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).
A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
we are using mmc alias , so mmc index have been changed.
now mmc dev 0 is emmc and mmc dev 1 is sdmmc.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
other two ports as host)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Since we've now integrated the A7k/8k support in the mvpp2 ethernet
driver, lets enable the support for both Marvell developments boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable support for Marvell Ethernet PHYs on A37xx platforms
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
LS1012A is Chassis-2 type SOC and shares same streamid definition.
This patch adds using streamids for ls1012a
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1046A is Chassis-2 type SOC and shares same streamid definition,
this patch adds using streamids for LS1046A.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The stream ID allocation for Chasis 3.0 devices can be shared among
LS1088, LS2088 and LS2080.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fix the offsets of MTD partitions on Nor flash on ls1043ardb,
ls1043aqds and ls1046aqds boards. Delete the rcw, uboot env and fman
partitions. Add user partitions for general usage.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable support for Marvell Ethernet PHYs on A37xx platforms
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SPL_DM on all AM43xx based platforms
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k). The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Scratch space can be used for features such as board detection. Define
an area within SRAM that can be used for this purpose.
[rogerq@ti.com] Rename EEPROM macro
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. So needs to enable them together.
DM FEC and SPI are not enabled, but they use gpio in board code.
So use gpio_request first to request the gpio, because DM_GPIO
is enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Use two separate partitions for the two firmware instances. Also
resize them to be of the same size which also makes the start of
the UBI partition nicely aligned to 0x400000.
In order to detect the new MTD layout and whether we run a U-Boot
with the new BCB format or not, introduce a variable called
"updlevel" which we can use in update/upgrade scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Use device-tree fixup to communicate the MTD partitions to the
kernel. Remove mtdparts from the kernel command line.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Limit memory used for relocation of FDT or initrd. This is
required to make sure that relocated artifacts are within lowmem.
If fdt_high or initrd_high are not set, U-Boot automatically
relocates artifacts to the end of memory. But this area won't
be part of lowmem and hence will not be accessible by the kernel
during early boot.
With VM split set to 2G/2G (i.MX default), only the 2GB Apalis
iMX6 is affected by that issue. With VM split set to 3G/1G (ARM
default) also modules with 1GB of memory are affected. With the
latter the amount of lowmem will be 760MiB.
The value must also not exceed available memory! Use a safe value
of 512MiB for Apalis and 256MiB for Colibri.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
CONFIG_SPL_ABORT_ON_RAW_IMAGE causes SPL to abort and move on when it
encounters RAW images, express this same functionality as a positive
option enabling support for RAW images: CONFIG_SPL_RAW_IMAGE_SUPPORT
Also move uses of this to defconfigs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Rework Kconfig logic a little, move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
Boards with an apparent need for the md5sum command had the connected
config symbol defined in their board header file.
Move this over to the respective defconfig files now that md5sum is
configured via Kconfig.
(This is a manual effort, which differs from moveconfig.py, not sure
who is right here. Boards except sandbox loose the md5sum command with
moveconfig.py, though it was explicitly mentioned in their config.h's)
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: migrate stih410-b2260]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM
Since The module will use the same devicetree, we patch
the ram size in ft_board_setup.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
We have a Kconfig name for the module types. Let's Use it.
Some feature selections and configurations are based on the
module. Module selection selects the CPU type.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot based
on the bootdevice so-that conditional macros for MMC via
CONFIG_BOOTCOMMAND should be avoided in config files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21)
Trying to boot from MMC2
U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Net: No ethernet found.
Hit any key to stop autoboot: 0
Booting from mmc ...
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
USDHC base address will assigned by SPL using fsl_esdhc_initialize
and u-boot with devicetree, hence no remove base address assignment
in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable MMC support.
The fsl sdhc driver needs regulator to enable power, so enable
regulator support.
And bootcmd and more env.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Commit e856bdcfb4 ("flash: complete CONFIG_SYS_NO_FLASH move with renaming")
obsoleted the CONFIG_SYS_NO_FLASH option, which still is in our
rk3188_common.h header, resulting in warnings like
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_NO_FLASH
So also drop it from the rk3188 header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
evb-rk3328 is an evb from Rockchip based on rk3328 SoC:
- 2 USB2.0 Host port;
- 1 USB3.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3328 is a SoC from Rockchip with quad-core Cortex-A53 CPU.
It supports two USB2.0 EHCI ports. Other interfaces are very
much like RK3288, the DRAM are 32bit width address and support
address from 0 to 4GB-16MB range.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add empty arch/arm/mach-rockchip/rk3328/Kconfig to avoid build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable all the CONFIGs which need by SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Drop CONFIG_ROCKCHIP_DWMMC for now due to build error:
Move changes to arch/arm/mach-rockchip/Kconfig to this patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SPL support for rk3399, default with of-platdata enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop Kconfig changes to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
We are using wrong mmc instance as boot target device now. below Jaehoon Chung's
patch use mmc alias which correct it. That make tinker board can not find mmc
device. So give it correct mmc device instance.
commit 02ad33aa3a
Author: Jaehoon Chung <jh80.chung@samsung.com>
Date: Thu Feb 2 13:41:14 2017 +0900
mmc: mmc-uclass: use the fixed devnum with alias node
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the core architecture code for the rk3188.
It doesn't support the SPL yet, as because of some
unknown error it doesn't start yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Drop these defines from rk3188_common.h
CONFIG_GENERIC_MMC, CONFIG_BOUNCE_BUFFER, CONFIG_DOS_PARTITION
CONFIG_PARTITION_UUIDS, CONFIG_CMD_PART:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
ISEE's U-Boot and Linux are using 1bit ECC scheme, while we
switched to 8bit ECC to fullfill flash specification requirements.
However when trying to run U-Boot on board with 1bit ECC'd data
on flash, UBI code takes several minutes to pass scan as reading
of every block ends with ecc error (which is also printed on
console).
So, until proper solution is developed, disable environment
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Raw uboot image is used in place of FIT image in secure boot.
The maximum allocated size of raw u-boot bin is 1MB in memory map.
Hence , CONFIG_SYS_MONITOR_LEN has been modified to 1 MB.
The bootscript (BS_ADDR) and its header (BS_HDR_ADDR) offset on
MMC have also been modified to accommodate the increase in uboot size.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the DDR interactive debugging to reduce the size of spl image.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases this is absolutely required, so select this for some secure
features. This also requires migration of RSA_FREESCALE_EXP
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
For the memory footprint reason, the Boot ROM can not load the ARM
Trusted Firmware BL1 directly when Trusted Board Boot is enabled.
The second stage loader is Socionext's own firmware, so rename it
for clarification.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
need to add before div in mmc update scripts. Otherwise we could
write one block more ba acident
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Playing with USB-to-Ethernet dongles it turns out,
that these will not work with special settings
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
depending on the use case different CMA sizes are
needed for linux. Add env var to enable passing CMA size
via kernel command line
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
The fdt_addr and ramdisk_addr_r are currently both defined to
0x83000000 and that's not going to work well for anyone. Move
the ramdisk_addr_r to 0x84000000.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Standard boot processes including distro boot generally expect the
default console to be defined.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.
Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The kernel partition in QSPI is 0x440000 large, not 0x400000. Fix this
in the environment, otherwise the kernel will fail to boot if it occupies
more space.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Keep it same with other boards otherwise i have to write special script for it..
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Albeit it's a typo, neither CONGIG_CMD_STORAGE nor CONFIG_CMD_STORAGE
are used anywhere, so remove the define from the board configs.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_CMD_ZIP is not defined by any board. I am moving
CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family.
I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP"
is better for this platform.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Now that we have a Kconfig for the API, convert the two boards that
are using this to Kconfig and remove CONFIG_API from the whitelist.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If SPL is used we want to use the generic SPL framework and boot
from SPI via a board-specific means. Add these options to the
board config file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If SPL is used we want to use the generic SPL framework and boot from SPI
via a board-specific means. Add these options to the board config file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
PPA binary needs to be relocated on secure DDR, hence marking out
a portion of DDR as secure if CONFIG_SYS_MEM_RESERVE_SECURE flag
is set
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, SPL (u-boot-spl.bin) and U-Boot (u-boot.bin) are stored
in non-volatile devices, and some environments are defined to update
the images easily.
When ARM Trusted Firmware is fully used, SPL is not used. U-Boot
proper is contained as BL33 into FIP (Firmware Image Package), which
is standard container used by ATF. Allow to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM supports authentication feature to prevent malformed
software from being run on products. The signature is added at the
tail of the second stage loader (= SPL in U-boot terminology).
The size of the second stage loader was 64KB, and it was consistent
across SoCs. The situation changed when LD20 SoC appeared; it loads
80KB second stage loader, and it is the only exception.
Currently, CONFIG_SPL_PAD_TO is set to 64KB and U-Boot proper is
loaded from the 64KB offset of non-volatile devices. This means the
signature of LD20 SoC (located at 80KB offset) corrupts the U-Boot
proper image.
Let's move the U-Boot proper image to 128KB offset. It uses 48KB
for nothing but padding, and we could actually locate the U-Boot
proper at 80KB offset. However, the power of 2 generally seems a
better choice for the offset address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When ARM Trusted Firmware is used, bl1.bin + fip.bin exceeds 512KB,
so the boot image and the current environment area will overlap.
Move the environment storage to 1MB offset.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The boot_ramdisk_high() checks the environment "initrd_high" and,
if it is set to (ulong)-1, skip the initrd relocation. This is
useful for faster booting when we know the initrd is already located
within the reach of the kernel.
Change "norboot" to copy images in order to make it work without
depending on the automatic relocation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The ARM64 Linux raw image now amounts to 15MB and it is getting
bigger and bigger. Using Image.gz saves about 8MB. The cost of
unzip is smaller than what we get by saving the kernel loading
from non-volatile devices.
The ARM32 Linux still uses zImage, a self-decompressor image,
so it should not be affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For clarification, move CONFIG symbols that affect SPL building
into a single place. Drop #ifdef CONFIG_SPL ... #endif since it is
harmless to define CONFIG_SPL_... during U-Boot proper building.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot needs to set up available memory area(s) in dram_init() and
dram_init_banksize(). It is platform-dependent how to detect the
memory banks. Currently, UniPhier adopts the memory banks _alleged_
by DT. This is based on the assumption that users bind a correct DT
in their build process.
Come to think of it, the DRAM controller has already been set up
before U-Boot is entered (because U-Boot runs on DRAM). So, the
DRAM controller setup register seems a more reliable source of any
information about DRAM stuff. The DRAM banks are initialized by
preliminary firmware (SPL, ARM Trusted Firmware BL2, or whatever),
so this means the source of the reliability is shifted from Device
Tree to such early-stage firmware. However, if the DRAM controller
is wrongly configured, the system will crash. If your system is
running, the DRAM setup register is very likely to provide the
correct DRAM mapping.
Decode the SG_MEMCONF register to get the available DRAM banks.
The dram_init() and dram_init_banksize() need similar decoding.
It would be nice if dram_init_banksize() could reuse the outcome
of dram_init(), but global variables are unavailable at this stage
because the .bss section is available only after the relocation.
As a result, SG_MEMCONF must be checked twice, but a new helper
uniphier_memconf_decode() will help to avoid code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables support for the smsc phy on the
stm32f746-disco board.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Series-changes 3:
- Add Acked-by tag to 'enable support for smsc phy on...'
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
chiliBoard is a development board which uses chiliSOM as its base.
Hardware specification:
* chiliSOM (TI AM335x, DRAM, NAND)
* Ethernet PHY (id 0)
* USB host (usb1)
* MicroSD slot (mmc0)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration file with parameters that are very likely to be shared by
all ast2500-based boards.
Add ast2500-board.c file with the init code that is very likely to be
shared by all ast2500-based boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
In the cases of some boards, a MACH_TYPE number is used which is either
not registered upstream or worse (for functionality) is re-using the
number of a different (or reference) platform instead. Make sure we
have a comment in these cases.
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
This board is using MACH_TYPE values that were clearly picked during
development and not registered. Remove rather than support.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the latest mach-types values we have many instances where we no
longer need to define a value and a few cases where the name (but not
value) have changed slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit 70b26cd057.
This is not a strict revert as it is easier to fix
board/atmark-techno/armadillo-800eva/armadillo-800eva.c to now the
correct name (same value) than to revert that change too.
Signed-off-by: Tom Rini <trini@konsulko.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The LS1046AQDS processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the trailing semicolon and space.
It's not necessary to have it on the last condition.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
According to doc/README.distro:
"fdt_addr_r:
Mandatory. The location in RAM where the DTB will be loaded or copied to when
processing the fdtdir/devicetreedir or fdt/devicetree options in
extlinux.conf."
So add the fdt_addr_r environment variable.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
USB Host scanning has been broken since v2016.05.
This is due to all the USB changes that happened between v2016.03
and v2016.05, especially:
2ef117fe4f usb: Remove 200 ms delay in usb_hub_port_connect_change()
a22a264ec3 usb: Change power-on / scanning timeout handling
So we need to increase the init delay to 2s using the usb_pgood_delay
environment variable.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
On mx6qsabreauto the parallel NOR width is 16 bits, so pass configure
CONFIG_SYS_FLASH_CFI_WIDTH correctly so that the CFI driver does not
use 8 bits by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch enables the MMC support for the SDHCI controller on the
Armada 7k db-88f7040 and the Armada 8k db-88f8040 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch enables the MMC support for the SDHCI controller on the
Armada 3700 db-88f3720 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Rename CONFIG_IMX31_PHYCORE_EET to CONFIG_TARGET_IMX31_PHYCORE_EET and
make this a distinct config target.
Signed-off-by: Tom Rini <trini@konsulko.com>
We may want to run different firmware before running U-Boot. For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader. In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.
This commit removes "select SPL" to make it configurable. This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI) Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT. The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint. This will mitigate the per-SoC
(sometimes per-board) defconfig burden.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
When falcon mode support was added, it was right around when SPL_OS_BOOT
was migrated to Kconfig. So first we must move the enablement to the
defconfig file. Next, it turned off EXT support rather than add the
information to allow for falcon mode from EXT. Add this information so
that the board compiles after 5d28b930f2.
Fixes: d96796ca23 ("mx6sabresd: Add Falcon mode support")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the generic "distro" boot framework to enable automatic DHCP boot.
MMC and USB are not yet implemented, so this is the only boot option.
The fdt and kernel addresses are adopted from downstream; ramdisk and
scriptaddr addresses were chosen arbitrarily.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Some scripts are calling the same functions, so these changes consolidate
common scripts together to reduce redundancy and shrink size a bit. This
also keeps the 'bootargs' variable from growing if manually called more
than one time. This also adds NAND booting scripts based on newly consolidated
scripts.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable UUID and GPT partition support for NXP's ARM based SoCs
i.e. LS1012A, LS1021A, LS1043A, LS1046A and LS2080A.
Also enable DOS partition for LS1012AFRDM boards.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe in ls2080a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe and E1000 in ls1043a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe and E1000 in ls1012a defconfigs and
removes unused PCIe related macro defines
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe in ls1021a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Once upon a time u-boot didn't support building with two usb host
controller types, these days it does. Enable XHCI in addition to the
existing EHCI support so user can plug usb devices in all available
ports regardless of the controller type.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since we're including ti_armv7_common, let's pull in DEFAULT_LINUX_BOOT_ENV
and remove unnecessary duplicative definitions. This patch also renames a
few environmental variables to match what is inside ti_armv7_common. This
should help future-proof any subsequent memory or memory location changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
This allows us to specify a FIT configuration that will automatically
use the correct images from the FIT blob.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Before we can sync with the latest mach-types.h file from the Linux
Kernel we need to remove some instances of MACH_TYPE_xxx from our
sources. As these values have been removed from the canonical upstream
source we should not be using them either, so drop.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Nick Thompson <nick.thompson@gefanuc.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MACH_TYPE for IGEP0032 was never officially used and has been
removed from upstream, so we must not use it. In order to remove this
we need to rework the status LED logic.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Dropped becuase
- driver and related configs not used any board.
- no dm conversion.
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Now that at least on the firefly board we have network support, enable
PXE and DHCP boot targets by default.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With CONFIG_ROCKCHIP_SPL_BACK_TO_BROM enabled,
the environment is inside u-boot.
So solve it by moving environment after u-boot.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
RK3288 using the dwc2 USB host controller, enable it and other usb host
funtion like storage and ether.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all. Remove.
Also, clean-up the README.socfpga. CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c27269953b
("mmc: complete unfinished move of CONFIG_MMC"). I see no grep hit
for the others.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Do the same change which was done in ZynqMP by:
"ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP"
(sha1: a8b6a156c0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to save environment as a file of FAT filesystem
on to SD card. The file will be saved with name uEnv.txt.
This environment will be retrieved during boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Increase environment size to 32K as the current default
environment itself is greater than 4K.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since usb ether gadget have support for driver model, so enable
usb ether gadget.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The predominantely 32-bit ARM targets try to compile the SPL in Thumb
mode to reduce code size.
The 64-bit AArch64 instruction set does not know an alternative, concise
encoding, so the Thumb build option should only be set for 32-bit
targets.
Likewise -marm machine options are only valid for ARMv7 targets.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Increase the nand kernel partition size, for supporting
large uImage files, maximum 8MiB.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add MAC support.
Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.
'cpsw_phy' env variable can override this setting.
Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.
Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The display is done in the device tree now, and there is no need
to pass 'display' kernel parameter any longer.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable USB gadget ethernet by default to have networking capabilities.
Tested using DHCP and TFTP to transfer kernel, DT, ramdisk.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
'fdtfile' is the preferred name for the variable that contains the
device tree blob according to the README file.
It also makes it consistent with other i.MX boards that use config_distro,
so change it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
armada100_spi.c and related env is zapping becuase
of "no DM conversion".
Cc: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
armada100_spi.c, related config options and related codes
are zapping becuase of "no DM conversion".
Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move USE_ARCH_MEMCPY/MEMSET options to Kconfig.
Make it "default y" for the ARMv7 architecture and make it
depend on !ARM64 && !SPL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>