Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To fused part, we need to disable nodes of dtb to let kernel boot.
To mfgtool, USB issue when using super-speed for mfgtool, temporally
work around the problem to use high-speed only.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To use one defconfig for all boot device, we have to runtime set
env offset and return env medium according to the boot device.
This patch overrides the env_get_offset and env_get_location to
implement the feature.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MP has 6 fused parts in each qualification tier, with core, VPU,
ISP, NPU or DSP fused respectively.
The configuration tables for enabled modules:
MIMX8ML8DVNLZAA Quad Core, VPU, NPU, ISP, DSP
MIMX8ML7DVNLZAA Quad Core, NPU, ISP
MIMX8ML6DVNLZAA Quad Core, VPU, ISP
MIMX8ML5DVNLZAA Quad Core, VPU
MIMX8ML4DVNLZAA Quad Lite
MIMX8ML3DVNLZAA Dual Core, VPU, NPU, ISP, DSP
Add the support in U-Boot
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
ROM SError happens on two cases:
1. ERR050342, on iMX8MQ HDCP enabled parts ROM writes to GPV1 register, but
when ROM patch lock is fused, this write will cause SError.
2. ERR050350, on iMX8MQ/MM/MN, when the field return fuse is burned, HAB
is field return mode, but the last 4K of ROM is still protected and cause
SError.
Since ROM mask SError until ATF unmask it, so then ATF always meets the
exception. This patch works around the issue in SPL by enabling SPL
Exception vectors table and the SError exception, take the exception
to eret immediately to clear the SError.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add imx_eqos_txclk_set_rate/imx_get_eqos_csr_clk to override the
weak function in driver
Add set_clk_eqos to configure eQoS clk
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current DM CLK is a bit complicated, for simplity, let DM clk only
support enable/disable/get_rate. For the expected rate settings,
we use non-DM clk to do that. Then we could have simple DM clk for
i.MX and could also share between SPL/U-Boot proper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
A53 CCM root max support 1GHz, to support high freq, we need
to switch ARM clk sources from ARM PLL directly.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol. Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB. Update these instances.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.
The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.
Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The iMX7 defines further DDRC ZQCTLx registers, however those were
thus far missing from the list of registers and not programmed. On
systems with LPDDR2 or DDR3, those registers must be programmed with
correct values, otherwise the DRAM may not work. However, existing
systems which worked without programming these registers before are
now setting those registers to 0, which is the default value, so no
functional change there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This reverts commit 1f63ee6566.
As reported by Ye Li on ML:
1. Removing the image_offset will break secondary (redundant) boot support for sd and emmc.
2. When booting from emmc boot partition, the image_offset is 0. But the flash.bin
generated by mkimage with imximage-8mp-lpddr4.cfg is for sd. It expects to be burn at 32KB offset.
The fit offset 0x60000 has already included the 32KB offset. So when you burn this flash.bin
to emmc boot partition at offset 0, the fit offset should subtract the 32KB (0x60000 - 0x8000).
Signed-off-by: Stefano Babic <sbabic@denx.de>
The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power
explicitly says both the DDR controller and the PHY must be reset in the
correct sequence. Currently the code only resets the controller. This
leads to a misbehavior where the system brings the DRAM up after reboot,
but the DRAM is unstable. Add the missing reset.
The easiest way to trigger this is by triggering WDT without having the
WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When not booting from FlexSPI, the offset computation is:
offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000;
When booting from SD card or eMMC user partition, image_offset is
0x8000. It is useless to add and remove 0x8000.
When booting from other device, image_offset is 0 so this computation is wrong.
Simplfy this computation to work on all booting devices.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
With yModem the FIT Image is only supplied once, so we can only
seek forward in the yModem supplied image and never backwards.
With the recent changes to the SPL mechanism, including loading
U-Boot first, FDT after, then the loadables, we must also reorder
the FIT image script to make sure that the loadables are last in
the FIT image.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we create software partition, we still need let parent
partition to configure sid, so move the check after sid failed.
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add code to check m4 partition booted or not, we will use this
to runtime set device tree file that passed to Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For fspi build, we will enable both SPL NOR support and SPL SPI
support. SPL will dynamically check the resource owner then
select corresponding boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing partition reboot, the boot image won't be reloaded by ROM,
it is just CPU reset to boot entry. The SW has to keep the boot image
inside the RAM unchanged. It includes both the TEXT section and DATA
section.
For SPL, the problem is DATA section will be updated at runtime, so in
next partition reboot the data is not same as the initial value from
cold boot. If any code depends on the initial value, then it will have
problem.
This patch introduces a mechanism to recover the data section
for partition reboot. It adds a new section in image for saving
data section. When from cold boot, the data section will be saved
to that new section at SPL early phase. When from partition reboot,
the data section will be restored from the new section.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When Trusty OS allocates the mem region from 0xfe0000000-0xffffffff,
the get_effective_memsize does not return correct memory size.
There is a check in get_effective_memsize to find the memreg where
the u-boot is running, and return the size of that memreg as the result
of get_effective_memsize. When using aligned start, the value is
0x80200000 since it is 2MB aligned. Thus the finding of memreg will
fail and return the PHYS_SDRAM_1_SIZE because u-boot text base is
0x80020000. This cause u-boot is relocated to the high memory where has
been occupied by Trusty OS.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDR memory from 0x88000000 to 0x8FFFFFFF is assigned to M4 on
QM and QXP. The M4 can allocate this memory by two ways,
in SCD or u-boot.
In this patch, u-boot addes the memory reserve node to DTB to pass
the info to kernel, no matter the M4 memory is reserved in SCD
or u-boot. So kernel won't access M4 reserved memory.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
add support for imx8qxp to read boot search count from fuse in nandbcb
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The original nandbcb tool was designed for imx6 only, when trying to
leverage it to replace the kobs-ng tool, we found the design is not
friendly for supporting all platforms. To support all iMX6/7/8 platforms
and for easy further maintain, I reconstruct the structure of the tool.
The main changes including:
1. Use platform_data to determine the logic branches rather than simply
use SOC name.
2. More data structures as parameter for functions.
3. Global variables to define the FCB/DBBT/FW locations.
4. Implement the kobs-ng default 4 FCB/4 DBBT/2 FW layout.
5. Support Hamming coding/ 40bit BCH/ 62bit BCH coding FCB.
6. Dump and compare all written FCB/DBBT to verify data integrity.
The tool has been verified on iMX6Q/DL, 6SX, 7D, 6ULL, iMX8QX, iMX8MM.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested on i.MX8MM EVK, imx8mm evk uses BCH
encoding and randomizer
modify macro and print size_t with %zx
use CONFIG_IMX8M because it should apply to imx8mq/mm/mn
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
bchtype in FCB should be associated to the gf_13/14 settings in BCH, fix
the issue and test on Micron 29F64G08CBABB, it can boot after the
change.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.
The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.
Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
So far u-boot only load SNSR25C for TMU main probe (probe 0). However,
kernel enables two probes. So it also needs to set default SNSR25C of
TCALIV1 for blank samples.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP thermal which has two probes and supports temperature range
from -40 to 125. The driver still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like iMX8MM, iMX8MN also needs SW to load TMU TASR and TCALIV registers
value from fuse before enabling TMU calibration. Otherwise the calibration
is not exact.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8MM, the default value of TMU registers TCALIV and TASR need
be loaded from fuse. HW won't do this, it expect SW loads them before
using TMU.
Reviewed-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are different parts from one SoC. Take i.MX6ULL for example,
some part might not have ENET, some might have; some might not have
USB, some might have. The information could be got from OCOTP,
to make one image support the different parts, we need runtime
disable linux kernel dts node and uboot driver probe if the
corresponding module not exists in the part.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
CONFIG_SPL_FAT_SUPPORT was removed in commit 0c3a9ed409
("spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT").
Fixup a leftover use of the symbol.
Fixes: 9d86dbd9cf ("imx: spl: implement spl_boot_mode for i.MX7/8/8M")
Signed-off-by: Harald Seiler <hws@denx.de>
It is hard to read code which contains nested ifdef blocks. Replace
them with normal if-blocks and the IS_ENABLED() macro. This is not only
more readable but also helps as both arms are validated by the compiler
in all cases.
Signed-off-by: Harald Seiler <hws@denx.de>
The CONFIG_SPL_FORCE_MMC_BOOT config flag is not needed as its behavior
is the correct one in all cases; using spl_boot_device() instead of the
boot_device parameter will lead to inconsistency issues, for example,
when a board_boot_order() is defined. In fact, this is the reason the
parameter was introduced in the first place, in commit 2b1cdafa9f
("common: Pass the boot device into spl_boot_mode()").
This reverts commit 772b55723b.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Boards may extend or re-define the boot list in their board_boot_order()
function by modifying spl_boot_list. E.g. a board might boot SPL from a
slow SPI NOR flash and then load the U-Boot from an eMMC or SD-card.
Or it might use additional MMC boot device in spl_boot_list for cases
when the image in SPI NOR flash is not found, so it could fall back to
eMMC, SD-card or another boot device.
Getting the MMC boot mode in spl_mmc will fail when we are trying to
boot from an MMC device in the spl_boot_list and the original board
boot mode (as returned by spl_boot_device()) is not an MMC boot mode.
Fix it by checking the asked MMC boot device from the spl_mmc_boot_mode()
argument.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
imx8m has the only implementation of reset_cpu() which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-developed-by: Harald Seiler <hws@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
If the cpu-idle-states is missing from the DT in the first place, do
not fail on removing in. Just move on and do not even print an error,
since not being able to remove something which is not there in the
first place is not an error and surely does not justify failing to
boot.
Turn the surrounding prints into debugs to reduce the useless noise.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx8m has the only implementation of `reset_cpu` which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing reset_cpu, in normal case the WDOG_B outputs immediately
after we clean WDA bit. But on mscale, the WDOG_B may be later than
internal reset, and cause PMIC not reset. As we enabled the SD3.0
support, the PMIC must be reset to reset SD card.
Change the reset_cpu to enable the WDOG_B for timeout as well, and set
WDOG timeout to 1s.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The fracpll decoding is using the bit definitions for int pll. Most of
them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK
for fracpll and correct all bit definitions in fracpll decoding.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.
Modified from Seb Fagard's downstream patch
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Seb Fagard <sebastien.fagard@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Latest SCFW has removed old MISC SECO commands. So update the codes
to use new SECO commands.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
parameter 'end address' must be inclusive of address range.
Modified from Seb's downstream patch.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the dump of DRAM PLL into "clocks" command
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
For ARM core clock, there are two input branches, and can select via mux:
one from ARM PLL directly, second from CCM A53 clock root.
Currently we are using second branch. But IC confirmed the CCM A53 root
signoff timing is 1Ghz, so we should switch to input from ARM PLL directly.
This patch fixes the CORE SEL slice configuration and switch ARM clock
to ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS
and HS400 configs to enhance the eMMC/SD access.
The change also needs to set usdhc clock to 400Mhz, and add the
off-on-delay-us to SD reset pin, otherwise some SD cards will
fail to select UHS mode in re-initialization.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update clock root table to let it be easy to configure clock at
very early stage. Also the core_sel mux parent should be A53 CLK
root and ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acquire ATF commit hash when booting U-Boot to make user easy
to know the ATF version.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the SIP macro to common header and unify the name to
make others could reuse them.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP speed grade use same layout as i.MX8MN, so reuse it for i.MX8MP
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx8mn speed grade fuse uses new definitions as below. So have
to update get_cpu_speed_grade_hz function to match it.
SPEED_GRADE[5:4] SPEED_GRADE[3:0] MHz
xx 0000 2300
xx 0001 2200
xx 0010 2100
xx 0011 2000
xx 0100 1900
xx 0101 1800
xx 0110 1700
xx 0111 1600
xx 1000 1500
xx 1001 1400
xx 1010 1300
xx 1011 1200
xx 1100 1100
xx 1101 1000
xx 1110 900
xx 1111 800
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
According to iMX8MM datasheet (IMX8MMIEC_Rev_D and IMX8MMCEC_Rev_D),
the speed grading for imx8mm is 800Mhz, 1.2Ghz, 1.6Ghz and 1.8Ghz.
Update them to get_cpu_speed_grade_hz function.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
All the FEC ethernet clock entries for iMX8MM are missing, while they
are already present on iMX8MQ. Fill in the nodes on iMX8MM, as the FEC
ethernet gets bogus clock information otherwise which makes ethernet
inoperable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The function's name is misleading as one might think it is used
generally to select the boot-mode when in reality it is only used by the
MMC driver to find out in what way it should try reading U-Boot Proper
from a device (either using a filesystem, a raw sector/partition, or an
eMMC boot partition).
Rename it to spl_mmc_boot_mode() to make it more obvious what this
function is about.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The i.MX6DP and i.MX6QP incorporate NoC interconnect logic
which needs to be configured in order to use external DDR memory.
This patch enables the SPL to configure the necessary registers
in accordance with the NXP engineering bulletin EB828.
Co-developed-by: Filip Brozović <fbrozovic@gmail.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
LDO mode may be already enabled by the ROM and enabling it again
can cause U-Boot to hang.
Avoid this problem by only enabling LDO mode if it is initially disabled.
Reported-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
These PMC0 definitions are already defined in the beginning
of the file, so remove the duplication.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update reference in files detected by
scripts/documentation-file-ref-check
doc/README.mxc_hab => doc/imx/habv4/*
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
The FIT config node has reversed ATF and u-boot: ATF is set to 'firmware' but
u-boot is set to 'loadables'.
This script can work previously because spl fit driver wrongly appends fdt to
all loadable images. With the issue fixed in commit 9d15d1d1c2 ("Revert
"common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"") the
u-boot in 'loadables' does not have fdt appended and fails to work. So correct
the script by moving u-boot to 'firmware' and ATF to 'loadables'.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reported-by: Matt Porter <mporter@konsulko.com>
Tested-by: Matt Porter <mporter@konsulko.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM
code to retrieve the core clock frequency. As the root clock is not
listed we currently get:
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Fix this by adding the missing entry, which results in:
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The call to spl_mmc_get_uboot_raw_sector() completely ignores and
overwrites the raw_sect value passed from the caller of spl_mmc_load().
Fix this by passing raw_sect to the function and returning the same
value in the default case.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Move the generic elf loading/validating functions to lib/
so that they can be re-used and accessed by code existing
outside cmd.
While at it remove the duplicate static version of load_elf_image_phdr
under arch/arm/mach-imx/imx_bootaux.c.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Since frac_pll_init() is only used in this file, change it to 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous
prototype for ‘frac_pll_init’ [-Wmissing-prototypes]
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Function init_usb_clk() is not used anywhere, so it can simply be deleted.
This was detected by the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:377:6: warning: no previous prototype
for ‘init_usb_clk’ [-Wmissing-prototypes]
void init_usb_clk(void)
^~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add imximage-8mp-lpddr4.cfg for imximage usage, almost same
as i.MX8MN ddr4 cfg, but with different ddr firmware
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The drivers/clk/imx/*.c are used for CLK dm case, the
clock_imx8mm.c is used for non CLK dm case, let's split
it. Sometimes it is hard to enable CLK dm in SPL stage,
considering code size, malloc size requirement, the splittion
will make it easy to use non CLK dm in SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP has similar architecture as i.MX8MN, but it has different
clk root and index, so add that to make i.MX8MP could use
the non-dm clock driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP use 0x182 as dummy id, 0xFF is not able the get the highest
bit, so enlarge bit mask to 0x1FF to make it could detect
cpu type correctly
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
fsl_esdhc_imx driver will call "mxc_get_clock(MXC_ESDHC_CLK +
dev->seq)", however mxc_get_clock wrongly handle MXC_ESDHC_CLK
as root clk and cause sd card could not be detected in U-Boot proper,
as below:
"Loading Environment from MMC... unable to select a mode"
Handle MXC_ESDHC_CLK in mxc_get_clock to fix the issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Fabio Estevam <festevam@gmail.com>
Add info about supported i.MX7, improve details the usage of
bcbonly subcommand.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Currently imx-specific bootaux command doesn't support ELF format
firmware for Cortex-M4 core.
This patches introduces a PoC implementation of handling elf firmware
(load_elf_image_phdr() was copy-pasted from elf.c just for PoC).
ELF64 binaries isn't supported yet.
This has the advantage that the user does not need to know to which
address the binary has been linked to. However, in order to handle
and load the elf sections to the right address, we need to translate the
Cortex-M4 core memory addresses to primary/host CPU memory
addresses (Cortex A7/A9 cores).
This allows to boot firmwares from any location with just using
bootaux, e.g.:
> tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}
Similar translation table can be found in the Linux remoteproc
driver [1].
[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch fixes the issue with broken bootaux command,
when M4 binary is loaded and data cache isn't flushed
before M4 core is enabled.
Reproducing:
> tftpboot ${loadaddr} ${board_name}/hello_world.bin
> cp.b ${loadaddr} 0x7F8000 $filesize
> bootaux 0x7F8000
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
1. Change information printed about loaded M4 binary, print the stack
pointer and reset vector addressed.
2. Add sanity check for the address provided as param.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch adds support for iMX6SX MMDC into the DDR calibration
code. The only difference between MX6DQ and MX6SX is that the SX
has 2 SDQS registers, while the DQ has 8.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
Instead of explicitly setting up each SDQS register, use a loop.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
Pull out the code turning SDQS pullups on and off into a separate
function, since it is replicated in two places in the code and it
is the single place in the entire function which is SoC dependent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
The %08X format returns just zeroes with tiny printf, which is
horribly confusing, especially when debugging DRAM calibration
problems. Change the format to %08x (with lowercase x), which
behaves correctly with either implementation of printf in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
add DM_SERIAL support for the aristainetos board, and
remove not used code from board code.
remove CONSOLE_OVERWRITE_ROUTINE.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).
Signed-off-by: Heiko Schocher <hs@denx.de>
This fixes commit <91435cd40d30> "ARM: i.MX6: exclude the ARM errata
from i.MX6 UP system"
for nitrogen6x. The above commit removed the errata for the board
since MX6Q/MXDL/MX6S is selected via CONFIG_SYS_EXTRA_OPTIONS
This restores the errata configs.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
IMX based platforms can have the DCD table located on different
addresses due to differences in their memory maps (ie iMX7ULP).
This information is required by the user to sign the images for secure
boot so continue making it accessible via mkimage.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
Recently the version check was improved to be able to determine that
we're running on SoC revision 2.1. A check for B0 was tightened so
that it now must equal 0x20 instead of being bigger than 0x20. On
some B0 chips the value returned is 0x1020 instead of 0x20. This
means even though it's B0, the check will fail and code relying on
the correct chip revision will make wrong decisions. There is no
documentation of those bits, but it seems that NXP always uses a
byte to encode the revision. Thus remove the upper bits to fix the
regression.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Make the PMU LDO configuration interface available to board code,
so that board code can reconfigure the internal LDOs of the SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
The NoC registers on i.MX6QP needs to be configured, otherwise some
usecases in the kernel behave incorrectly, such as rotation and resize.
Currently the NoC registers are not configured in the kernel, so
configure them in U-Boot like it is done in the NXP U-Boot tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The LDOVL definitions is common to all the modes, not only RUN mode,
so in order to avoid confusion, remove the _RUN notation from the PMC1
LDOVL definitions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Introduce the CONFIG_LDO_ENABLED_MODE option so that i.MX7ULP boards
designed to operate with LDO enabled mode can work with 0.95V at LDO
output in RUN mode as per the datasheet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
As per the i.MX7ULP datasheet, it can boot in LDO enabled mode
or LDO bypass mode.
Print the LDO mode status in the U-Boot log for convenience.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
When CONFIG_$(SPL_)CLK not defined, the clock controller device
not exist, so to avoid boot failure for platform not have
CONFIG_$(SPL_)CLK, add a check.
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN support loading images with rom api, so we implement
reuse board_return_to_bootrom to let ROM loading images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN has similar architecture with i.MX8MM, so it could reuse
the clock code of i.MX8MM, but i.MX8MN has different CCM root
configurations, so need a separate root entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.
Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Move code for writing FCB/DBBT pages to a separate function
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for updating FCB/DBBT on i.MX7:
- additional new fields in FCB structure
- Leverage hardware BCH/randomizer for writing FCB
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Borrow ID reading code from Ye Li (NXP U-Boot, commit ID 5b443e3e2617)
but drop imx-mkimage commit ID reading since we now use in tree mkimage.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.
Also add image authentication call when loading container images.
Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It will be easy to separate SD/EMMC when booting in SPL stage, then
no need to bother which device is BOOT_DEVICE_MMC1/2.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_ETH and remove code that is no longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.
This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Signed-off-by: Claudius Heine <ch@denx.de>
Introduce disable_ipu_clock(). This is done in preparation for
configuring the NoC registers on i.MX6QP in SPL.
Afer the NoC registers are set the IPU clocks can be disabled.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The code can be made simpler by using setbits_le32(), so switch
to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
THe RVT data includes a major and minor version in its header
parameter. Add a new command to print this out.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
i.MX7ULP uses the same MMDC controller IP as found on i.MX53
and i.MX6, so build mmdc_size.c for i.MX7ULP as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The original imx_ddr_size() implementation had some
issues reported by checkpatch like this:
CHECK: Prefer kernel type 'u32' over 'uint32_t'
#127: FILE: arch/arm/mach-imx/mmdc_size.c:16:
+ uint32_t ctl;
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#151: FILE: arch/arm/mach-imx/mmdc_size.c:40:
+ unsigned ctl = readl(&mem->ctl);
Fix all of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place imx_ddr_size() into a separate file.
The motivation for doing this is to be able to easily reuse
imx_ddr_size() on i.MX7ULP.
Currently imx_ddr_size() is inside arch/arm/mach-imx/cpu.c, which
is not built for i.MX7ULP.
Changing the logic to allow building cpu.c for i.MX7UP would
require adding several ifdef's, leading to a not a very elegant
solution.
To allow better reuse, just place imx_ddr_size() into a common
mmdc_size.c file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Apologies to everyone whose board I broke by attempting to return
MMC1 or MMC2. I misunderstood how the MMC indexing worked.
This reverts commit 14d319b185.
Signed-off-by: Adam Ford <aford173@gmail.com>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
To avoid hardcoded offset when adding u-boot.cnt to flash.bin, we use
flexible offset which is calculated based on the size of the container
image generated int the first stage. And pad u-boot.cnt at 1KB
alignment.
So add code to get the offset when SPL loading u-boot.cnt.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because we need to get cpu freq in print_cpuinfo at very early stage,
so we need to make sure the ccm be probed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When DM_MMC enabled, the USDHC index in U-Boot is the USDHC port.
To directly return devno, we could avoid add board specific code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce clk implementation for i.MX8MM, including pll configuration,
ccm configuration. Mostly will be done clk dm driver,
but such as DRAM part, we still use non clk dm driver, because we
have limited sram.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ and i.MX8MM use different analog pll design, but they
share same ccm design.
Add clock_imx8mq.h for i.MX8MQ
keep common part in clock.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To i.MX8MM SCTR clock is disabled by ROM, so before timer init
need to enable it.
To i.MX8MQ, it does not hurt the clock is enabled again.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set trustzone region 0 to allow both non-secure and secure access
when trust zone is enabled. We found USB controller fails to access
DDR if the default region 0 is secure access only.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When running with OPTEE, the MMU table in u-boot does not remove the OPTEE
memory from its settings. So ARM speculative prefetch in u-boot may access
that OPTEE memory. Due to trust zone is enabled by OPTEE and that memory
is set to secure access, then the speculative prefetch will fail and cause
various memory issue in u-boot.
The fail address register and int_status register in trustzone has logged
that speculative access from u-boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no HDMI on i.MX8MM, so we need to remove HDMI entry, then
we could not reuse imximage.cfg, so create a new one.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix the FIT image metadata for i.MX8 to result in the intended boot
order (SPL -> ATF -> U-Boot).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Similar to "spl_sd.cfg", this patch introduces "spl_qspi.cfg" so that
all i.MX6 based boards can use it, when they use SPL and QSPI boot
mode.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds the missing boot mode detection for QSPI boot on
i.MX6UL/ULL. Without it, booting with SPL from QSPI NOR does not work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
The default CSF_SIZE defined in Kconfig is too high and SPL cannot
fit into the OCRAM in certain cases.
The CSF cannot achieve 0x2000 length when using RSA 4K key which is
the largest key size supported by HABv4.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's recommended to pad CSF binary to 0x2000 and append DEK blob to
deploy encrypted boot images.
As the maximum DEK blob size is 0x58 we can reduce CSF_SIZE to 0x2060
which should cover both CSF and DEK blob length.
Update default_image.c and image.c to align with this change and avoid
a U-Boot proper authentication failure in HAB closed devices:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x32 length=0x6131 version=0x38
bad length magic=0x32 length=0x6131 version=0x38
bad version magic=0x32 length=0x6131 version=0x38
spl: ERROR: image authentication fail
Fixes: 96d27fb218 (Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets")
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
This change tries to fix the following problem:
- The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR
memory.
As a result the spl_boot_device() will return SPI-NOR as a boot device
(which is correct).
- The problem is that in 'falcon boot' the eMMC is used as a boot medium to
load kernel from its partition.
Calling spl_boot_device() will break things as it returns SPI-NOR device.
To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is
introduced to handle this special use case. By default it is not defined,
so there is no change in the legacy code flow.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not
supported as of time of this conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this commit the display5 device would use I2C driver supporting
driver model (DM_I2C).
The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize
on-bus devices according to device tree description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Allow enable_ipu_clock() to be built for SPL code. This is done
in preparation for configuring the NoC registers on i.MX6QP in SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add OP-TEE device tree node for Linux according to args passed from ATF.
If ATF has been built with OP-TEE running, boot_pointer[1] will indicate
that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8QM, sid is programmable, so we could program sid according the
value encoded in device tree.
This patch support legacy bindings which are still being used by XEN
and new bindings used by Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When resource is not assigned to non-secure Linux, if linux continue
to use the node, linux may crash or hang. So need to set the node
status to disabled for not owned resources.
The resource id is in the power-domains property in device tree,
so parse the power-domains property to get the resource id and
use scfw api to check whether it is owned by current partition.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
1. This fixes linking issues when building with DM_VIDEO enabled mxsfb
driver.
2. Provide proper defines for both VIDEO=y and DM_VIDEO=y.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/psci.c:
warning: no previous prototype for ‘psci_set_state’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_arch_cpu_entry’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_features’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_version’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_affinity_info’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_migrate_info_type’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_on’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_off’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_reset’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_off’ [-Wmissing-prototypes]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For a single binary approach for imx6 quad/dual/duallite/solo it
is necessary to enable CONFIG_SATA for quad/dual. On the other hand
on imx6 duallite/sole SATA is not available.
Therefore sata_remove() is skipped according to a blacklist scheme.
Adding further imx derivates is probably not recessary as they are
usually not pin-compatible and therefore a different board with its
own configuration.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
According to iMX6DQ RM, the minor field (low 8 bits) in DIGPROG is not
aligned on silicon revision 1.3. So update get_cpu_rev to correct the
revision.
0x00630002 Silicon revision 1.2
0x00630005 Silicon revision 1.3
0x00630006 Silicon revision 1.6
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, when the spl_boot_device checks the boot device, it
will only return MMC1 when it's either sd or eMMC regardless
of whether or not it's MMC1 or MMC2. This is a problem when
booting from MMC2 if MMC isn't being manually configured like in
the DM_SPL case with SPL_OF_CONTROL.
This patch will check the register and return either MMC1 or MMC2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
According to hab.c code we have to notify the ROM code if the MMU is
enabled or not. This is achieved by setting the "pu_irom_mmu_enabled"
to 0x1.
The current address in hab.c code is wrong for i.MX6SL, according to ROM
map file the correct address is 0x00901c60.
As we are writing in the wrong address the ROM code is not flushing the
caches when needed, and the following HAB event is observed in certain
scenarios:
--------- HAB Event 1 -----------------
event data:
0xdb 0x00 0x14 0x41 0x33 0x18 0xc0 0x00
0xca 0x00 0x0c 0x00 0x01 0xc5 0x00 0x00
0x00 0x00 0x07 0xe4
STS = HAB_FAILURE (0x33)
RSN = HAB_INV_SIGNATURE (0x18)
CTX = HAB_CTX_COMMAND (0xC0)
ENG = HAB_ENG_ANY (0x00)
Update MX6SL_PU_IROM_MMU_EN_VAR to address this issue.
Reported-by: Frank Zhang <frank.zhang@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
The DM iMX PCI driver has DM_FLAG_OS_PREPARE set and will call
imx_pcie_remove() from the .remove callback. Do not call it from
the architecture code again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
CPU frequency reporting failed with the following error message being
printed:
sc_pm_get_clock_rate: resource:507 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QM RevB A53 at 0 MHz
Fix this by differentiating between the A35 as found on the i.MX 8QXP
and the A53 as found on the i.MX 8QM SoCs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Correct uart clock root ID. Incorrect ID may result the
clock is gated because rate value 0 is returned in
imx_get_uartclk()
The ID can be ignored if CONFIG_SKIP_LOWLEVEL_INIT is not enabled
because init_clk_uart() will enable all uart clocks in that case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Skip secure related initialization in arch_cpu_init if low level
init is skipped. Because these should be done in early stage
firmware, such as ARM trusted firmware.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add common plugin codes to call ROM's hwcnfg_setup and generate IVT2
header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Building with Travis CI complained and stopped with the following error:
+cc1: fatal error: opening output file spl/u-boot-spl.cfgout: No such
file or directory
+compilation terminated.
This fixes commit caceb739ea ("imx: build flash.bin for i.MX8") which
took SPL being enabled on i.MX8 for granted.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to mxsfb device.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Allow using bootaux also on VF610 aka Vybrid.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and ipu nodes to enable driver binding to ipu device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When framebuffer driver init is failed, we should return the err value not 0.
So the video init can exit immediately.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
At default, u-boot reserves the memory from SP - 4KB to DRAM end for
lmb in arch_lmb_reserve. So lmb won't allocate any memory from it.
But we found the 4K gap for SP is not enough now, because some FDT
updating operations are added in our u-boot before jumping to kernel,
which needs larger stack. This causes the lmb allocated memory is overwritten
by stack.
Fix the issue by implementing the board_lmb_reserve to reserve from
SP - 16KB to memory end for lmb.
Signed-off-by: Ye Li <ye.li@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like it was done on imx6 in commit 9236269de5 ("imx: mx6: Fix
implementantion reset_misc")
Do not call lcdif_power_down() in the SPL case to fix the following
build error:
LD spl/u-boot-spl
MKIMAGE u-boot.img
arch/arm/mach-imx/built-in.o: In function `reset_misc':
/home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down'
scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The following NXP application notes and manual recommend to ensure the
IVT DCD pointer is Null prior to calling HAB API authenticate_image()
function:
- AN12263: HABv4 RVT Guidelines and Recommendations
- AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using
HABv4
- CST docs: High Assurance Boot Version 4 Application Programming
Interface Reference Manual
Commit ca89df7dd4 ("imx: hab: Convert DCD non-NULL error to warning")
converted DCD non-NULL error to warning due to the lack of documentation
at the time of first patch submission. We have warned U-Boot users since
v2018.03, and it makes sense now to follow the NXP recommendation to
ensure the IVT DCD pointer is Null.
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error
if a DCD pointer is present in an image being authenticated by calling the
HAB RVT API. Older versions of HAB will process and run DCD if it is
present, and this could lead to an incorrect authentication boot flow.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return
32768Hz to reflect the reality.
This also keeps the values in sync with the Linux clock tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current implementation of hab_auth_img command needs ivt_offset to
authenticate the image. But ivt header is placed at the end of image
date after padding.
This leaves the usage of hab_auth_img command to fixed size or static
offset for ivt header. New function "get_image_ivt_offset" is introduced
to find the ivt offset during runtime. The case conditional check in this
function is same as boot_get_kernel in common/bootm.c
With this variable length image e.g. FIT image with any random size can
have IVT at the end and ivt_offset option can be left optional
Can be used as "hab_auth_img $loadaddr $filesize" from u-boot script
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
