The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
When we have a FIT image being used by SPL by default that means the
most common case is that we'll never run into a legacy image. Disable
legacy image support by default in that case to reclaim space.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow the code to build when FS_FAT is not enabled, and thus
spl_load_image_fat() is not provided.
A subsequent patch should add alternative raw access U-Boot main image
load method.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The init_sata() routine is only present when DM_SCSI is not enabled.
Don't call init_sata() when DM_SCSI is enabled. The code will fall back
to scsi_scan() in this case.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Add sensible defaults for the FAT partition selection and the main
U-Boot image file name. This allows spl_sata to build when the board
headers does not select them explicitly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This allows to silence ubi and ubispl individually.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.
This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.
This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Move the ubispl configuration to KConfig and drop them from the
whitelist.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
The pointer to struct atf_image_info in
bl31_params_mem.bl31_params.bl31_image_info is not initialized before
being dereferenced. This can cause U-Boot to crash right before jumping
to the BL31 ATF binary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: bcc1726a7b ("spl: add support to booting with ATF")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for loading u-boot FIT images over the USB SDP protocol in
the SPL
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[Various build fixes]
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL DFU uses dfu_alt_info_N variable name to determine the DFU
configuration, where N is the name of the media (e.g. ram). It does
not use the plain dfu_alt_info. Print the name of the missing env
variable in case of a failure instead of printing dfu_alt_info,
which is just the name of the parameter passed to spl_dfu_cmd().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
As explained in include/configs/imx6_spl.h. the i.MX6 SPL
size limit is 68KB (4KB header + 64KB max size).
Provide such limit for all i.MX6 boards that use SPL
to detect SPL size overflow in build time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
When introduced this limit was an int but was then changed to hex
without noting as much in the prompt nor changing existing users. Put
this back to an int.
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Fixes: 2577015dc5 ("spl: add overall SPL size check")
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
By default the configuration of the PMC is to have an external crystal
connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not
do any driving, and the XIN needs to be provided with a proper signal.
This is the MOSCXTBY bit in the PMC main clock generator register.
The SPL needs to properly initialize the PMC registers before switching
to external clock signal and raising the clock to the cruise speed.
Also created Kconfig for this specific configuration.
By default this is disabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Set the spl_image->fdt_addr pointer both for simple fitImage configuration
as well as full fitImage configuration, to let spl_perform_fixups() access
the DT and perform modifications to it if necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
FIT_IMAGE_TINY is used to reduce the size of the SPL by removing os-type
tracking and recording the loadables into the loaded FDT. When this option
is enabled, it is assumed that the next stage firmware is u-boot.
However this does not play well with the SPL_OS_BOOT option that enables
loading different type of next stage firmware, like the OS itself.
When SPL_OS_BOOT is used, do not disable os-tracking. The added footprint
is about 300 Bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
This patch adds a short message to the SPL NAND loader, which displays
the source and destinations addresses including the size of the
loaded image, like this:
U-Boot SPL 2019.04-rc3-00113-g486efd8aaf (Mar 15 2019 - 14:18:02 +0100)
Trying to boot from NAND
Loading U-Boot from 0x00040000 (size 0x000a0000) to 0x22900000
I find this message quite helpful - hopefully others do so as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for loading fully featured fitImages over YModem in SPL.
This is useful when various advanced features of full fitImages are
needed in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
In case the gunzip() call fails, it will print an error message.
If that happens within the YModem session, the error message will
not be displayed and would be useless. Move the gunzip() call out
of the YModem session to make those possible error messages visible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
In case spl_parse_image_header() errors out, terminate the YModem
session, otherwise we won't get any further output.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
If FIT_IMAGE_TINY is enabled, spl_fit_image_get_os returns -ENOTSUPP.
In this case, we should default to IH_OS_U_BOOT not to IH_OS_INVALID.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
To find out how big the early malloc heap must be in SPL, add a debug
print statement that dumps its usage before switching to relocated heap
in spl_relocate_stack_gd() via CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
SPL currently does not check uImage CRCs when loading U-Boot.
This patch adds checking the uImage CRC when SPL loads U-Boot. It does
this by reusing the existing config option SPL_CRC32_SUPPORT to allow
leaving out the CRC check on boards where the additional code size or
boot time is a problem (adding the CRC check currently adds ~1.4 kByte
to flash).
The SPL_CRC32_SUPPORT config option now gets enabled by default if SPL
support for legacy images is enabled to check the CRC on all boards
that don't actively take countermeasures.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
SPL only needs to be able to read from SPI Flash to load next stage and
does not really need write/erase etc. Therefore in order to reduce SPI
Flash code size in SPL, enable SPI_FLASH_TINY, that only supports
reading from SPI flash, as default.
Note: Since, SPI_FLASH_TINY does not support SPI_FLASH_BAR,
SPI_FLASH_TINY is not enabled for boards with SPI controllers that
cannot support 4 byte addressing.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most of the time SPL only needs very simple FAT reading, so having
CONFIG_IS_ENABLED(FAT_WRITE) to exclude it from SPL build would help
to save 64KiB default max clustersize from memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Add support for gunzip-ing gzip-compressed uImages in the SPL Ymodem code.
Loading data over Ymodem can be gruelingly slow, gzip-ing the data can
reduce that aggravating slowness at least slightly (depends on the data,
u-boot.bin compresses to ~1/3 of it's original size on ARM64), hence add
optional support for decompressing gzip-compressed uImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
