This causes conflicts on chromebook_link64. Move it to after U-Boot where
there should be plenty of space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that all board use binman instead of this script, drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this board uses a custom script to produce the .its file.
Update it to use binman instead. Binman can create all the images that
are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
On mediatek various files that need to be created by binman. It does not
make sense to enumerate these in the Makefile. They are described in the
configuration (devicetree) for each board and we can simply run binman
(always) to generate them.
This avoid sprinkling the Makefile with arch-specific code.
Also update the binman definition so that idbloader.img is only needed
when SPL is actually being used.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Quite a few boards using this SoC family don't use binman, yet
CONFIG_BINMAN is enabled for all of them. But the option should only be
enabled if we expect binman to produce an image. Calling binman when the
device tree is missing, etc. will cause failer.
Add a condition so that CONFIG_BINMAN is only enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present only the ARMv7 tegra SoCs actually use binman to create an
image. Change the config to reflect this, since otherwise running binman
will produce an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple binman config and enable CONFIG_HAS_ROM so that U-Boot
produces a ROM for jerry.
Change the binman image definition to support multiple images, since it
may be used to build both u-boot-rockchip.bin and u-boot.rom
Signed-off-by: Simon Glass <sjg@chromium.org>
Most x86 boards build a u-boot.rom which is programmed into SPI flash. But
this is not unique to x86. For example some rockchip boards can also boot
from SPI flash.
Also, at least on x86, binary blobs are sadly quite common. It is not
possible to build a functional image without them, and U-Boot needs to
know this at build time.
Introduce a new CONFIG_HAS_ROM option which selects whether u-boot.rom is
built and a new CONFIG_ROM_NEEDS_BLOBS option to indicate whether binary
blobs are also needed. If they are not needed, it is safe to build the ROM
always. Otherwise we still require the BUILD_ROM environment variable.
For now this affects only x86, but future patches will enable this for
rockchip too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Add the PCIe EP node for ls1046a.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev2 requires 4KB space for type0 and 4KB
space for type1 iATU window. Increase configuration
size to 8KB to have sufficient space for type0
and type1 window.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The workaround has been implemented in PBI phase, so remove
the duplicated implementation from U-Boot.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This enables SYS_I2C_MXC to fix a bug that
failed to boot from sd card with
image u-boot-with-spl-pbl.bin
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two issues:
(1) The spin table doesn't convert the endianness of the jump address.
Although there is code for it, the result isn't used at all (x0).
(2) If something goes wrong, the function returns. But that doesn't
make sense at all.
Use the actual converted jump address as destination to fix. If
there is an error, jump to a trap loop. And rearrange the code exception
level switching code to make it smaller and clearer.
This reduces the size of the spin table code section from 696 bytes to
424 bytes. If CONFIG_ARMV8_SWITCH_TO_EL1 the code size reduced from 696
bytes to 632 bytes.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On ARM64, a 64kb region is reserved for the runtime services code.
Unfortunately, this code overlaps with the spin table code, which also
needs to be reserved. Thus now that the code is relocatable, allocate a
new page from EFI, copy the spin table code into it, update any pointers
to the old region and the start the secondary CPUs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a new variable secondary_boot_code_start, which holds a pointer to
the start of the spin table code. This will help to relocate the code
section. While at it, move the size variable from the end to the
beginning so there is a common section for the variables. Remove any
other symbols.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the spin table is in a separate module, this is no longer
necessary. Drop it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This function is not used outside the module. Make it static.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no need to cast around. Assign the address to the local
variable and use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Only the PowerPC architecture needs this function. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix the alignment so it will match the comments. The spin table has to
be 8 byte aligned, so ".align 3" is enough.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Don't use LDR to load a pointer to a function. This will generate a
literal which cannot be relocated. Use ADR which is PC-relative and
therefore can easily be relocated.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move it out of lowlevel.S into spintable.S. On layerscape, the secondary
CPUs are brought up in main u-boot. This will make it possible to only
compile the spin table code for the main u-boot and omit it in SPL.
This saves about 720 bytes in the SPL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The generic armv8 code already has support to bring up the secondary
cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to
the spin table code; instead just return early and let the common armv8
code handle the jump. This way we can actually use the CPU_RELEASE_ADDR
feature.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased, Removed kontron_sl28.h change as file does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Make the print of the starting address a debug output and pretty print
the info about online cores.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Spin tables are broken with bootefi. This is because - in contrast to
the booti call chain - there is no call to smp_kick_all_cpus(). Due to
this missing call the secondary CPUs are never released from their "wait
for interrupt state", see secondary_boot_func() in lowlevel.S.
Originally, this "wait for interrupt" is there to make sure, the spin
table is cleared before the secondary cores read it for the first time.
But the boot flow for the layerscape architecture is different from
that. The CPUs are release from their BootROM _after_ U-Boot's
spin-table is cleared, see fsl_layerscape_wake_seconday_cores() in mp.c.
Thus, there is no need to wait for this interrupt and no need for
kicking all cores on cpu_release. An atomic 64bit write to the
spin-table and a "sev" is sufficient.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to
define it per board; the ls1028a_common.h is really board dependent and
only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE
when ARCH_LS1028A is selected.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch imports the device tree and required bindings to permit
the device tree to build for the R8Z774A1 (RZ/G2M).
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to build boards based on the R8A774A1, there needs to
be a config option from which to enable other drivers and/or flags
for this SoC.
Signed-off-by: Adam Ford <aford173@gmail.com>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Make memory node available to SPL in prepration to updates to SiFive
DDR RAM driver to read memory information from DT.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
