Using SMC relocation microcode patch or USB-SOF microcode patch
will disable DPRAM memory from 0x2000 to 0x2400 and from 0x2f00
to 0x3000.
At the time being, init RAM is setup to use 0x2800-0x2e00, but
the stack pointer goes beyond 0x2800 and even beyond 0x2400.
For the time being we are not going to use any microcode patch
that uses memory about 0x3000, so reorganise setup to use:
- 0x2800 - 0x2e00 for init malloc and global data and CPM buffers
- 0x3000 - 0x3c00 for init stack
For more details about CPM dual port ram, see
commit b1d62424cb ("powerpc: mpc8xx: redistribute data in CPM dpram")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
We do not want to merge documentation that produces Sphinx warnings.
scripts/kernel-doc uses environment variable KDOC_WERROR to determine
if warnings should be treated as errors.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With relocation, CPM parameter RAM can be anywhere in the
dual port RAM, so don't split dual port RAM.
Remove dparam and dparam16 members of struct comm_proc
PROFF_XXX become offsets from the start of dual port RAM,
then they are now consistant with the offsets in RPBASE
registers.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
In order to know the motherboard type earlier, perform I/O ports
initialisation and FPGA loading in board_early_init_f() instead
of board_early_init_r().
This is needed to be able to load mpc8xx CPM microcode base on
motherboard type and before starting to use the CPM.
Console is not available yet so remove the printfs.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This function uses the same base name as all the others in this file, so
it is not easy to run just that one test. Add a _base suffix so that it
can be run on its own.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Main U-Boot is loaded by sector number, not by partition GUID type.
Fixes: 70415e1e52 ("board: sifive: add HiFive Unmatched board support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The number of the partition that U-Boot SPL loads the main U-Boot from is
defined as 2 by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2. The
partition type GUID is not used currently.
Reword the description of the boot process to make it clearer.
Fixes: 5ecf9b0b8a ("board: starfive: add StarFive VisionFive v2 board support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Support for the VisionFive 2 board is not contained in the most recent
OpenSBI release (v1.2).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Guide shows incorrect usage of proftool, which is confusing. If proftool
is used w/o '-o' argument it complains like following
$ ./sandbox/tools/proftool -m sandbox/System.map -t trace dump-ftrace > trace.dat
Must provide trace data, System.map file and output file
Usage: proftool [-cmtv] <cmd> <profdata>
s/>/-o/ fixes it and proftool outputs decoded data to trace.dat
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch drops 0x prefixes because all numbers are interpreted as HEX
by default.
Also, it fixes the mismatch between input arguments and output at 'mmc
write' example. Now it's 256 (0x100) blocks.
Signed-off-by: Alexander Shirokov <shirokovalexs@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct the function documentation.
Fixes: ca031c0827 ("dm: core: introduce uclass_get_device_by_of_path()")
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Variable old_outdir cannot be used before assignment.
The assignment must occur before the try block.
tools/dtoc/test_fdt.py:796:26:
E0601: Using variable 'old_outdir' before assignment
(used-before-assignment)
Add missing space in assignment.
Fixes: a004f29464 ("binman: Tidy up _SetupDtb() to use its own temporary file")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Freescale PCIe Root Port has PEXCSRBAR register at position of PCI BAR0.
PCIe Root Port does not have any PCIe memory, so returns zero when trying
to read from PCIe Root Port BAR0 and ignore any writes.
Signed-off-by: Pali Rohár <pali@kernel.org>
The host compiler is not failing on warnings at present, when the
-E flag is used in buildman. Add the required flag to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com>
Fix comments error in EVENT_DEBUG description:
this get usefui -> this to get useful
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix comments syntax error in event description:
creasted -> created
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix comments syntax error in SPL_LOAD_FIT_APPLY_OVERLAY description.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of always printing ethaddr of MAC 0, print eth%daddr of the current MAC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move all the network information printing into print_eth(),
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Map fdt_blob and new_fdt to sysmem, otherwise $fdtcontroladdr
and bdinfo output do not match and the bdinfo output address
is not a valid address accessible via sandbox memory accessors.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Variable old_outdir cannot be used before assignment.
The assignment must occur before the try block.
tools/dtoc/test_fdt.py:796:26:
E0601: Using variable 'old_outdir' before assignment
(used-before-assignment)
Add missing space in assignment.
Fixes: a004f29464 ("binman: Tidy up _SetupDtb() to use its own temporary file")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the hush shell variable assignment and clear.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The u-boot hush shell doesn’t support the unset command to clear a
variable and therefore an empty value ("c=") should be a valid value
for the set_local_var function to clear the variable. This partial
reverts commit aa72252963 ("common: cli_hush: avoid dead code") and
only checks for a `=` in the string. Additionally explicit call the
unset_local_var function to remove the variable if the value is empty.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Updates for starqltechn and other qualcomm platforms, hi3798mv200,
Broadcom Northstar, and mediatek platforms
- Drop omap5_uevm, and assorted TI platform updates
- Add MAX14526
It adds compatible "hisilicon,hi3798mv200-dw-mshc" for HC2910 SoC
Hi3798MV200 to probe this mmc driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers
Details: A device lockup can occur during the second read of any CPSW
subsystem register after any MAIN domain power on reset (POR). A MAIN
domain POR occurs using the hardware MCU_PORz signal, or via software
using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR.
After these resets, the processor and internal bus structures may get
into a state which is only recoverable with full device reset using
MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.
Workaround(s): To avoid the lockup, a warm reset should be issued after
a MAIN domain POR and before any access to the CPSW registers. The warm
reset realigns internal clocks and prevents the lockup from happening.
Workaround above errata by calling do_reset() in case of cold boot in
order to trigger warm reset. This needs enabling SYSRESET driver in R5
SPL to enable TI SCI reset driver.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add support to detect daughtercards (GESI Ethernet card) in-order
to set the MAC address of the main CPSW2G interface.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Update the default BOOTCOMMAND to provide an automatic and easier way
to configure ethernet PHY before loading the firmware.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Add board specific devicetree for Bananapi R3 SBC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Commit dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and
related functions") changed the logic deciding to set R0 and R1
registers for V1 devices.
Before:
/* Also set PUPD/R0/R1 if the pin has them */
err = mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_PUPD, !pullup);
if (err != -EINVAL) {
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R0, r0);
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R1, r1);
}
After:
/* try pupd_r1_r0 if pullen_pullsel return error */
err = mtk_pinconf_bias_set_pullen_pullsel(dev, pin, disable, pullup,
val);
if (err)
return mtk_pinconf_bias_set_pupd_r1_r0(dev, pin, disable,
pullup, val);
Tracing mtk_pinconf_bias_set_pullen_pullsel shows that the function
always either returns 0 in case of success or -EINVAL in case any error
has occurred. Hence the logic responsible of the decision to program R0
and R1 has been inverted.
This leads to problems on BananaPi R2 (MT7623N) when booting from
SDMMC, it turns out accessing eMMC no longer works since
U-Boot 2022.07:
MT7623> mmc dev 0
Card did not respond to voltage select! : -110
The problem wasn't detected for a long time as both eMMC and SDMMC work
fine if they are used to boot from, and hence R0 and R1 were already
setup by the bootrom and/or preloader.
Fix the logic to restore the originally intended and correct behavior
and also change the descriptive comment accordingly.
Fixes: dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and related functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to 8.
The C7x and VPAC have been overwhelming the DSS's access to the DDR
(when it was accessing via the Non Real-Time (NRT) Queue), primarily
because their functional frequencies, and hence DDR accesses, were
significantly higher than that of DSS. This led the display to flicker
when certain edgeAI models were being run.
With the DSS traffic serviced from the RT queue, the flickering issue
has been found to be mitigated.
The am62a qos files are auto generated from the k3 resource partitioning
tool.
Section-3.1.12, "QoS Programming Guide", in the AM62A TRM[1], provides
more information about the QoS, and section-14.1, "System Interconnect
Registers", provides the register descriptions.
[1] AM62A Tech Ref Manual: https://www.ti.com/lit/pdf/spruj16
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
J721E and J7200 have same file j721e_init.c which had the firewall
configs for J721E being applied on J7200 causing the warnings. Split the
firewalls for both the boards to remove those warnings.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The current documentation for Snapdragon based Samsung
and Qualcomm boards is vague in the sense that at one place
it mentions that u-boot can be used as a replacement for ABL
bootloader and at another it mentions that u-boot is loaded
as an Android boot image through ABL.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Currently a few 'board/qualcomm/../Makefile' point to incorrect
path of sdm845 board file.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
K3 devices have some firewalls set up by ROM that we usually remove so
that the development is easy in HS devices.
While removing the firewalls disabling a background region before
disabling the foreground regions keeps the firewall in a state where all
the transactions will be blacklisted until all the regions are disabled.
This causes a race for some other entity trying to access that memory
region before all the firewalls are disabled and causes an exception.
Since the background regions configured by ROM are in such a manner
that they allow all transactions, don't touch the background regions at
all.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
