This reverts commit bcc51c1512.
Commit bcc51c1512 ("ARM: uniphier: move lowlevel debug init code
after page table switch") was intended to support lowlevel debug for
sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to enable lowlevel debug earlier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit f0776a5517 ("spl: dm: Kconfig: SPL_CLK depends on
SPL_DM"), the following warning is displayed:
$ make uniphier_v8_defconfig
warning: (ARCH_ZYNQ && ARCH_ZYNQMP && STM32F7 && CLK_UNIPHIER) selects
SPL_CLK which has unmet direct dependencies (CLK && SPL_DM)
While I am here, I am removing the prompt to make it user-unconfigurable
option so that "select CLK_UNIPHIER" can be omitted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
since commit: b529993e02 "spl: add hierarchical defaults for SPL_LDSCRIPT"
taurus board stopped working. Use the ldscript from
arch/arm/cpu/u-boot-spl.lds (as before this patch) fixed it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
CONFIG_SYS_GENERIC_GLOBAL_DATA is no longer used by any board or
platform, so support for it can be dropped.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ATF can leave the MMC IP in a state where U-Boot mmc driver
can't enumerate the eMMC.
This patch provides a mmc0_reset_clk() function like we
already so do sd card controller which resets the IP
when entering U-Boot.
With this patch applied eMMC partitions are successfully
enumerated again.
=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device
=> mmc part
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000800 0x00000fff "vrl"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 496847ab-56a1-4cd5-a1ad-47f4acf055c9
2 0x00001000 0x000017ff "vrl_backup"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 61a36fc1-8efb-4899-84d8-b61642efa723
3 0x00001800 0x00001fff "mcuimage"
<snip>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Signed-off-by: Tom Rini <trini@konsulko.com>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Signed-off-by: Tom Rini <trini@konsulko.com>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Reported-by: Coverity (CID: 166335)
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that sandbox is building cmd/mtdparts.c Coverity has looked at the
code and found a number of issues. In index_partitions() it is possible
that part will be NULL, so re-work the checks and debug statements to
take this into account. We have a number of string buffers that we
print to in the exact size of, and use string functions on, so we need
to ensure they are large enough to be NULL terminated. In
device_parse() it is not possible for num_partitions to be 0 (we would
have hit a different error first) so remove logically dead code.
Finally, in parse_mtdparts() if we have an error we need to free the
memory allocated to dev.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Coverity (CID: 166334, 166333, 166332, 166329, 166328)
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 089df18bfe ("lib: move hash CONFIG options to Kconfig") moved
CONFIG_SHA1, CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and
CONFIG_SHA_PROG_HW_ACCEL config options to Kconfig. So in the case of
SPL, CONFIG_SPL_HASH_SUPPORT enables CONFIG_SHA1 and CONFIG_SHA256 which
enables SHA SW library by default. But in the case of platforms with
SHA HW library support, SHA SW library becomes redundant and increases
size of SPL by approx 18K. Rework the code so that we have named
members and only have either software or hardware versions of the
algorithm, depending on the relevant config options. Update the comment
around hash_algo to reflect this as well.
Reported-by: Sumit Garg <sumit.garg@nxp.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
On some systems `python` is `python3` (for instance, Archlinux). The
`PYTHON` variable can be used to point to `python2` to have a successful
build.
The use of `PYTHON` is currently limited in the Makefile and needs to be
extended in other places:
First, pylibfdt is required to be a Python 2 binding (binman imports
pylibfdt and is only compatible Python 2), so its setup.py needs to be
called accordingly. An alternative would be to change the libfdt
setup.py shebang to python2, but the binding is actually portable. Also,
it would break on system where there is no such thing as `python2`.
Secondly, the libfdt import checks need to be done against Python 2 as
well since the Python 2 compiled modules (in this case _libdft.so) can
not be imported from Python 3.
Note on the libfdt imports: "@if ! PYTHONPATH=tools $(PYTHON) -c 'import
libfdt'; then..." is probably simpler than the currently sub-optimal
pipe.
Reviewed-by: Jonathan Gray <jsg@jsg.id.au>
Do not dereference bmp before the check if it is NULL.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fix the IOMUX setting for SDcard CMD pin at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dts from kernel is using rk3228-pinctrl as compatible name,
need to sync with it to make the driver work.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The description for eMMC/SDIO/SDMMC src is not correct,
update the CRU_CLKSEL11_CON value definition according to TRM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRAM start address is not 0, so need to update the last bank size
as:
DRAM start addr + DRAM_SIZE - last bank start addr
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fdtdec.h is included, but not used in rk3399-board-spl.c: remove the
'#include'-statement.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There are two same gmac node, remove one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
UEFI API functions have different return types.
Some return a value of type EFI_STATUS other don't.
We therefore should not cast the return value of EFI_EXIT
to another type than the expression passed to EFI_EXIT.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This changes pci_mmc driver to use PCI_CLASS_SYSTEM_SDHCI instead of
individual vendor id & device id pair to support generic PCI SD host
controller.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Sysam stmark2 board is a generic and fully (hw and sw) open board, with
a mcf54415 Coldfire CPU, 128MB of DDR2, 16MB of SPI flash and SD card
as non volatile memories, and a wifi module included on-board.
The board is actually used mainly for Coldfire custodian testing activity
related to the mcf5441x Coldfire family.
For further information please see: http://sysam.it/cff_stmark2.html
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
---
Changes in v2:
- remove CMD_REGINFO
- add board information in commit message
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init
is required. This patch moves this ddr/sdram early initalization
away from start.S (to be board related).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
During the the conversion to $(SPL_TPL_), the SPL_ fragment was
left over for the NOR, XIP and YMODEM boot methods in SPL, making
these unselectable.
This commit fixes this by dropping the spurious 'SPL_' fragment
from each line.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reported-by: Bo Shen <voice.shen@gmail.com>
Fixes: f94e643 (spl: consistently use $(SPL_TPL_) to select features for SPL and TPL builds)
Update the tx_delay and rx_delay to match the timing for
rk3399-firefly board to improve the stability of gmac data
transfer.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch allows to show the EXT_CSD[179] partition_config
register info, just by specifying the dev param:
U-Boot> mmc partconf 0
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x0
BOOT_PARTITION_ENABLE: 0x0
PARTITION_ACCESS: 0x0
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable driver model for MMC (including BLK), SATA and USB. Note that USB
does not yet work correctly since the nodes are disabled. Hopefully this
can be resolved by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_BLK is enabled our weak board_mmc_init() will not be called.
Since there is no clock driver for MX6 yet, we must manually enable the
clocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for using driver model for SATA with the cm_fx6 board. The old
code remains for now to permit testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use fsl_esdhc_init() with driver model. Move the mmc_init() out
of this function so that we can use it for our common init.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to store the mmc and configuration structure in
platform data. Set up structure up and use it for non-DM as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_init_common() can fail it should return an error code. Update
this and also adjust the timeout mechanism to use get_timer(), which is a
more common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_reset() can fail it should return an error code. Update this
and also adjust the timeout mechanism to use get_timer(), which is a more
common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model wants to use the core functions in this file but accesses the
driver-private data in a different way. Move the code into new 'common'
functions and set up stubs to call these. Also sort the operations into
alphabetical order for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we will not use mmc->priv to access driver-private data.
To accomodate this, update internal functions so that we can pass the
private data directly. This will allow the caller to obtain it as it
prefers.
Signed-off-by: Simon Glass <sjg@chromium.org>
