It applies to non-Freescale 85xx boards as well as Freescale boards,
so it doesn't belong in board/freescale. Plus, it needs to come out
of nand_spl if it's to be used by the new SPL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Commit 97b24d3d51 "common: Add symbol
handling for generic lists into Makefile" introduced build errors in many
nand_spl targets, complaining of a missing u-boot.lst. When not doing an
out-of-tree build, $(obj) expands to nothing, so GCC ended up being given
-I with no argument (or rather, -ansi was the argument). The failure
didn't show up during a -j1 build because it was picking up the non-SPL
version of u-boot.lst.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
This patch adds essential components for generation of the contents of
the linker section that is used by the linker-generated array. All of
the contents is held in a separate file, u-boot.lst, which is generated
at runtime just before U-Boot is linked.
The purpose of this code is to especially generate the appropriate
boundary symbols around each subsection in the section carrying the
linker-generated arrays. Obviously, the interim linker code for actual
placement of the variables into the section is generated too. The
generated file, u-boot.lst, is included into u-boot.lds via the linker
INCLUDE directive in u-boot.lds .
Adjustments are made in the Makefile and spl/Makefile so that the
u-boot.lds and u-boot-spl.lds depend on their respective .lst files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
This change reduces the SPL size by removing the redundant syncs produced
by out_be32 and just replies on one final sync
Done with:
sed -r '/in_be32/b; s/(out_be32)\(([^,]*),\s+(.*)\)/__raw_writel(\3, \2)/g' -i `git grep --name-only sdram_init nand_spl/`
Signed-off-by: Matthew McClintock <msm@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have a requirement to wait a period of time before enabling the
DDR controller
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Let's use the more appropriate udelay for the nand_spl. While we
can't make use of u-boot's full udelay we can atl east use a for
loop that won't get optimized away .Since we have the bus clock
we can use the timebase to calculate wall time.
Looked at reusing the u-boot udelay functions but it pulls in a lot
of code and would require quite a bit of work to keep us within the
very small space constrains we currently have
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We were not comparing the SVRs properly previously. This comparison
will properly shift the SVR and mask off the E bit
This fixes the boot output to show the correct DDR bus width:
512 MiB (DDR3, 16-bit, CL=5, ECC off)
instead of
512 MiB (DDR3, 32-bit, CL=5, ECC off)
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, for NAND boot for the P1010/4RDB we hard code the DDR
configuration. We can still dynamically set the DDR bus width in
the nand spl so the P1010/4RDB boards can boot from the same
u-boot image
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
dram_init function in board/davinci/common/misc.c does not get
compiled for spl builds, thus rendering inclusion of memsize.c
useless.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
move the board/davinci/common/misc.c file to
arch/arm/cpu/arm926ejs/davinci/misc.c, so all
davinci boards can use this functions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the hawkboard use these definitions instead of
defining its own.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
s3c64xx.c implemented its own nand_read_byte, nand_write_buf and
nand_read_buf functions. This provoked a regression when these functions
were made public by patch 55f429bb39614a16b1bacc9a8bea9ac01a60bfc8.
This deletes these duplicated functions from s3c64xx.c and adds the generic
implementations in nand_base.c to the spl Makefile. It also adds
-ffcuntion-sections and -gc-sections to the compilation flags of the SPL to
avoid errors originating from unused functions in nand_base.c.
Description of the regression:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/108873
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
No need to have a config.mk to only store a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
And various defines to enable NAND support and NAND spl code for the
P1010RDB platform.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since we rename _end to __bss_end__, But we need add _end symbol for
the end of u-boot image.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit f326cbba98 breaks mx31pdk,
as the _end section in u-boot.lds is missing for the nand_spl
production.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Modify eLBC based platform's NAND loader Makefile to preprocess nand loader
linker script and then use it.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 6dc1ece "Introduce a new linker flag LDFLAGS_FINAL" modified a
number of Makefiles in a way that broke out-of-tree builds. The
problem was that $(nandobj) was used before it got defined.
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In the nand_spl feature of SMDK6400. Add some relocation symbols to
nand_spl/board/samsung/smdk6400/u-boot.lds to fix the compile error.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
commit 8aba9dceeb
Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGS
breaks the usage of --gc-section to build nand_spl. We still need linker option
--gc-section for every uboot image, not only the main one. LDFLAGS_FINAL passes
the --gc-sections to each uboot image.
To get the proper linker flags, we use LDFLAGS and LDFLAGS_FINAL to replace
PLATFORM_LDFLAGS in the Makefile of each nand_spl board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting
from NAND.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By rearranging the linker script we get support for
relocation of -fpic for free.
Move __got2_entries outside _GOT2_TABLE_ defining scope
matching the rest of PowerPC
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Recent GCC (4.4+) performs out-of-line epilogues in some cases, when
optimizing for size. It causes a link error for _restgpr_30_x (and similar)
if libgcc is not linked.
It actually increases size with very small binaries, due to the fixed size
of the out-of-line code, and not having any functions that actually need to
restore more than 2 or 3 registers. But I don't see a way to turn it off,
other than asking GCC to optimize for speed -- which may also increase
size for some boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
As more Davinci 8xx board can be added, move common code
to be shared between boards.
* rebased ontop of Sugosh's patches
* moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to
arch/arm/include/asm/arch-davinci/davinci_misc.h from to
arch/arm/include/asm/arch-davinci/da8xx_common.h
* don't define dram functions in PRELOADER
* move sync_env_enetaddr into existing EMAC ifdef
* use misc.c in hawkboard nand_spl
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove the board_init_f function from nand_spl/nand_boot.c. This
function is to be defined by all boards using the nand_spl
functionality in their individual board directory.
Currently this function was being used by the smdk6400 board. Added
the board specific function definition.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This commit adapts 4xx boards for partial linking with --gc-sections.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: David Updegraff <dave@cray.com>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Larry Johnson <lrj@acm.org>
Cc: Peter De Schrijver <p2@mind.be>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Cc: Daniel Poirot <dan.poirot@windriver.com>
Acked-by: Stefan Roese <sr@denx.de>
Apply the same fix for 83xx as was done for 85xx in commit
96196a1f75.
Without this, NAND SPLs are built with the text base intended for the main
image, resulting in a broken, very large u-boot-nand.bin.
The block of defines for NAND boot is moved closer to where
CONFIG_SYS_TEXT_BASE is defined. We can't directly use
CONFIG_SYS_NAND_U_BOOT_DST in the definition of CONFIG_SYS_TEXT_BASE because
autoconf.mk will include the literal text "CONFIG_SYS_NAND_U_BOOT_DST",
but at least keep them close and point out that they're supposed to be
the same.
Signed-off-by: Scott Wood <scottwood@freescale.com>
older ld emitted all ELF relocations in input sections named
.rel.dyn, whereas newer ld uses names of the form .rel*. The
linker script only collected .rel.dyn input sections. Rewrite
to collect all .rel* input sections.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
