Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to add a second flash.
The 'ubiattach' command is featured in two versions:
- if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined:
this is the version as up to now
- if CONFIG_KM_UBI_PARTITION_NAME_APP is defined:
a check on 'actual_bank' will be done to determine the flash to boot
from.
Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and
CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader
and the applications.
Example:
In the board config do:
... snip ...
"boot:" \
"768k(u-boot)," \
"128k(env)," \
"128k(envred)," \
"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" \
"app:" \
"-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");"
... snap ...
You may also need to enable the second flash:
... snip ...
/* additional featured for COGE5 */
... snap ...
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Calucations of PRAM needs to take into account the 'rootfssize'.
Memory available to the linux kernel 'mem=' is in all cases set to the total
memory size minus the pram size.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Moved eeprom config to specific part, to allow bigger eeprom write pages
for km_kirkwood designs. Write page only used for env eeprom in std use
cases. 24C128 has page size of 64bytes -> 8 time faster.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Now we use the standard u-boot make to build the Kirkwood binary.
The output file is u-boot.kwb. So use this name for the tftp
update function to avoid confusion, because this is the binary we
need on Kirkwood.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
All the km boards uses CRAMFS images where the kernel is stored.
This isn't architecture specific because we use it on ARM and
POWERPC.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
These defines and the header keymile_hdlc_enet.h are obsolete
due to the removed hdlc code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The debug environment which is stored in textfiles in the
scripts directory was reworked. Two usecase are now present
which can be executed simply from the default environment:
run develop: this configures the environment to setup the
rootfs via nfs
run ramfs: this configures the environment to setup the
rootfs in ram
Each architecture now has a "arch" variable which is used
to load the architecture specific debug scripts and to set
the rootpath for NFS.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The test SW is started when the test_bank variable is set.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This is the second step to simplify and decrease the default
environment for the keymile boards. The release usecase formaly
used to set the production environment was removed and the default
configuration is now the production environment. So the formar
environment variable "release" which has done a lot of things
in the past, simply erase the current environment and do a reset
which forces u-boot to setup the default environment again.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
This define is marvell specific, so it should be present in km_arm.
It is however not needed there either, since we set it to the default
value that is already set in include/asm/arch-kirkwood/config.h
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The pnvram size was used later from start scripts in linux. Therefore
it was added to the default environment.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
This is a first step to simplify the default environment. Move all
the environment variables which are only needed for debugging
purpose to textfiles in the scripts directory. In case of debugging
these files can be loaded via tftp into RAM and set via the env import
command. Other variables are identified as obsolete and were removed.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
BoardId and HWKey are used to identify the HW class of a given board.
The correct values are stored in the inventory eeprom. During creation
time of a boot package the boardId and HWkey for the SW is stored in
the default environment and burned into the flash. During boottime
the values in the inventory and in the environment are compared to
avoid starting of a SW which is not authorized for this board.
Some bootpackages are allowed to run on a set of different boardId
hwKey. In this case the environment variable boardIdListHex was added
to the default environment. In this case the command iterates over the
pair values and compares them with the values read from the inventory
eeprom.
The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
