This adds a new Kconfig option CONFIG_MIPS_INIT_STACK_IN_SRAM which
a SoC can select if it supports some kind of SRAM. Together with
CONFIG_SYS_INIT_SP_ADDR the initial stack and global data can be
set up in that SRAM. This can be used to provide a C environment
also for lowlevel_init().
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move the code for setting up the initial stack and global data
to a macro to be able to use it more than once.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Clear cp0 status while preserving implementation specific bits.
Set bits BEV and ERL as the arch specification requires after
a reset or soft-reset exception.
Extend and fix initialization of watch registers. Check if additional
watch register sets are implemented and initialize them too.
Initialize cp0 count as early as possible to get the most
accurate boot timing.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When booting from ROM, early exceptions can't be handled
properly. Instead of busy-looping give the developer the
possibilty to examine the situation. Invoke an UHI
exception operation which can be read as unhandled exception
by a hardware debugger if one is attached. If the debugger
doesn't support UHI, the exception is read as unexpected
breakpoint.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This adds a compile time option to include code for static
exception vectors. Static exception vectors are only needed,
when the U-Boot entry point is equal to the CPU reset exception
vector address. For instance this is the case when U-Boot is
used as ROM in Qemu or booted from parallel NOR flash. When
U-Boot is booted from RAM (e.g. loaded there by SPL), the
exception vectors need to be setup dynamically, which is done
in follow-up commits.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Some systems are configured such that multiple CPUs begin running from
their reset vector following a system reset. If this occurs then U-Boot
will be run on multiple CPUs simultaneously, which causes all sorts of
issues as the multiple instances of U-Boot clobber each other.
Prevent this from happening by simply hanging with an infinite loop if
we run on a CPU whose ID, as determined by GlobalNumber or EBase.CPUNum
as appropriate, is non-zero.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The relocate_code function was handling cache maintenance incorrectly.
It copied U-Boot to its new location, flushed the caches & then
proceeded to apply relocations & jump to the new code without flushing
the caches again. This is problematic as the instruction cache could
potentially have already fetched instructions that hadn't had relocs
applied.
Rework this to perform the flush_cache call using the code in the
original copy of U-Boot, after having applied relocations to the new
copy of U-Boot. The new U-Boot can then be jumped to safely once that
cache flush has been performed.
As part of this, since the old U-Boot is used up until after that cache
flush, complexity around loading values from the GOT using a jump & link
instruction & loads from a table is removed. Instead we can simply load
the needed values with PTR_LA fromt the original GOT.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
During boot we set Config.K0=2 (uncached) such that any accesses to the
kseg0 memory region are performed uncached before the caches are
initialised. This write to the Config register introduces an execution
hazard between it & any following memory accesses (such as the load of
_gp), which we need to clear in order to ensure those memory accesses
are actually performed uncached. Clear this execution hazard with the
insertion of an ehb execution hazard barrier instruction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Map the Global Control Registers (GCRs) provided by the MIPS Coherence
Manager (CM) in preparation for using some of them in later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
On systems where cache initialisation doesn't require zeroed memory (ie.
systems where CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD is not defined)
perform cache initialisation prior to lowlevel_init & DDR
initialisation. This allows for DDR initialisation code to run cached &
thus significantly faster.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The coprocessor 0 Config register includes 9 implementation defined
bits, which in some processors do things like enable write combining or
other functionality. We ought not to wipe them to 0 during boot. Rather
than doing so, preserve their value & only clear the bits standardised
by the MIPS architecture.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enable use of the instruction cache immediately after it has been
initialised. This will only take effect if U-Boot was linked to run from
kseg0 rather than kseg1, but when this is the case the data cache
initialisation code will run cached & thus significantly faster.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
In MIPS assembly there have historically been 2 variants of immediate
addition - the standard "addi" which traps if an overflow occurs, and
the unchecked "addiu" which does not trap on overflow. In release 6 of
the MIPS architecture the trapping variants of immediate addition &
subtraction have been removed. In preparation for supporting MIPSr6,
stop using the trapping instructions from assembly & switch to their
unchecked variants.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Fix 32 vs 64 bit load/store instructions. Access CP0_WATCHHI as
32 Bit register. Use 64 Bit register access for clearing gd_data
and copying U-Boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Argument boot_flags of board_init_f() should be set to 0 as
$a0 may be utilized in lowlevel_init() or mips_cache_reset()
or previous stage boot-loader.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Correctly annotate _start and relocate_code as functions to
produce more readable disassembly code generated by objdump.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Unify and move code in arch/mips/cpu/mips[32|64]/ to arch/mips/cpu/.
The CPU specific config.mk files need to remain until
CONFIG_STANDALONE_LOAD_ADDR is converted to a global Kconfig symbol.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
All current CPUs and SoCs are based on MIPS32 arch. The complete
code resides in the global arch/mips/cpu directory. This is not
suitable if other MIPS architectures like MIPS64 or Octeon should
be supported in the future.
To achieve this the current CPU code is moved to its own mips32
subdirectory. All MIPS32 boards have to use mips32 as config switch
in board.cfg.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
