The pcie_dw_mvebu configure ATU regions for memory, configuration
and IO space types. However the latter is not obligatory
and when not specified in the device tree, causes wrong
ATU configuration. Fix that by adding a dependency on the
detected PCIE regions count.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/18136
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
commit 6ecbe13756 ("drivers: pci: imx: add imx_pcie_remove function")
attempted to resolve an issue caused by MX6QDL not having a proper
intneral PCIe core reset and thus hanging during kernel init if the
bootloader had enabled PCI.
The issue exists for IMX6Q, IMX6D, IXM6S, and IMX6DL. Fix the case for
IMX6S and IMX6DL getting missed.
This fixes IMX6S and IMX6DL with PCI enabled in U-Boot booting for
Linux v4.11+.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the highest subordinate bus number after probing the devices
under the bus for setting up the bridge correctly.
The commit 42f3663a3f ("pci: Update to use new sequence numbers")
removed this but it is required if a PCIe bridge is under the bus.
Fixes: 42f3663a3f ("pci: Update to use new sequence numbers")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Trying to clear PIO_START register when it is non-zero (which indicates
that previous PIO transfer has not finished yet) causes an External
Abort with SError 0xbf000002.
This bug is currently worked around in TF-A by handling External Aborts
in EL3 and ignoring this particular SError.
This workaround was also discussed at:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
Implement a proper fix to prevent this External Abort. As it is not
possible to cancel a pending PIO transfer, simply do not start a new one
if previous has not finished yet. In this case return an error to the
caller.
In most cases this SError happens when there is no PCIe card connected
or when PCIe link is down. The reason is that in these cases a PIO
transfer takes about 1.44 seconds. For this reason we also increase the
wait timeout in pcie_advk_wait_pio() to 1.5 seconds.
If PIO read transfer for PCI_VENDOR_ID register times out, or if it
isn't possible to read it yet because previous transfer is not finished,
return Completion Retry Status value instead of failing, to give the
caller a chance to send a new read request.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the PCIe host controller driver for MIPS Octeon II/III.
The driver mainly consist of the PCI config functions, as all of the
complex serdes related port / lane setup, is done in the serdes / pcie
code available in the "arch/mips/mach-octeon" directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add support for the DW PCIe controller found in the Amlogic Meson AXG and
G12 (G12A, G12B, SM1) SoCs.
This uses the common DW PCIe helpers introducted previously.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
With the introduction of pcie_dw_rockchip, and need to support the DW PCIe in the
Amlogic AXG & G12 SoCs, most of the DW PCIe helpers would be duplicated.
This introduce a "common" DW PCIe helpers file with common code merged from the
dw_ti and dw_rockchip drivers and adapted to fit with the upcoming dw_meson.
The following changes will switch the dw_ti and dw_rockchip to use these helpers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Green Wan <green.wan@sifive.com>
[bmeng: remove the blank line at EOF of drivers/pci/pcie_dw_common.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The copy buffer, if enabled, prevents booting from coreboot correctly,
since no memory is allocated for it. Allow it to fall back to disabled
in this situation. This ensures that a console is displayed, even if
it is slow.
Signed-off-by: Simon Glass <sjg@chromium.org>
As on some incipient Layerscape platforms (LS1043A series) there isn't
separate PF control register block, these registers reside in the LUT
register block, so when the driver detected there isn't 'ctrl', it will
assign the 'lut' address to the ls_pcie->ctrl.
The current code allocate memory for the struct ls_pcie with random
contents, this can result in skipping to assign the ls_pcie->ctrl with
the 'lut' address, then further crash with the incorrect address.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Marvell Armada 3720 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in U-Boot PCIe controller driver aardvark for
both PCI vendor id and PCI subsystem vendor id.
This change affects PCI vendor id of PCIe root bridge emulated by Linux
kernel. With this change Linux kernel reports correct vendor id 11AB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the driver only supports 32-bit bus and cpu address.
The controller's outbound registers/fields for extended address
are not programmed. Let's program them to support 64-bit bus and
cpu address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
devfdt_get_addr_index() returns fdt_addr_t which might be a 64-bit
physical address. Use map_physmem() to return the virtual address
that can be used by a 32-bit machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For the QEMU ppce500 machine, LAW registers are not implemented
hence CONFIG_FSL_LAW is not turned on and all LAW APIs are not
available. We should wrap all LAW registers programming in the
mpc85xx PCI driver with CONFIG_FSL_LAW.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit e002474158 ("pci: pci-uclass: Dynamically allocate the PCI regions")
changes 'struct pci_controller'.regions from pre-allocated array of
regions to dynamically allocated, which unfortunately broken lots of
boards that still use the non-DM PCI driver.
This patch changes the non-DM fsl_pci_init driver to dynamically
allocate the regions, just like what's done in the pci uclass driver.
Fixes: e002474158 ("pci: pci-uclass: Dynamically allocate the PCI regions")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Write bdf address in a same way in mvebu_pcie_read/write_config.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the map address and mask must be power of two per documentation,
adjust the code accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to access the PCIe root bus space and configure it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
So far we've assumed a fixed configuration for inbound windows as we had
a single user for this controller. But the controller's DMA constraints
were improved starting with BCM2711's B1 revision of the SoC, notably
available in CM4 and Pi400. They allow for wider inbound windows. We can
now cover the whole address space, whereas before we where limited to
the lower 3GB.
This information is passed to us through DT's 'dma-ranges' property and
it's specially important for us to honor it since some interactions with
the board's co-processor assume we're doing so (specifically the XHCI
firmware load operation, which is handled by the co-processor after
u-boot has correctly configured the PCIe controller).
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Make sure we handover the PCIe controller in a clean state. Some of the
devices hanging from the PCIe bus might need to be properly reset
through #PERST in order for Linux to be able to initialize them.
This is specially important in order to properly initialize Raspberry Pi
4 B and 400's USB chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch changes the PCI config routines in the Armada XP / 38x driver
to not allow access to the PCIe root ports.
While updating the Armada XP based theadorable to the latest mainline
and testing it with the DM PCI driver I noticed, that the PCI root
bridge was being configured incorrectly. Resulting in the PCIe Intel
WiFi was not working correctly in Linux. With this patch applied, all
PCIe devices work without any issues in Linux again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch completely removes CONFIG_PCI_ENUM_ONLY from the PCI code as
it is not configured for any board (any more). With this removal, some
PCI related files get cleaned up a bit.
Additional, dm_pciauto_setup_device() is now static, as it's not
referenced from any code outside of this C file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Value pcie->dev in function pcie_advk_probe() is not initialized yet
so use dev as argument for dev_dbg()/dev_warn().
Function pcie_advk_wait_pio() itself prints error message on failure
so do not print duplicate error message in caller.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Rockchip dwc based PCIe controller driver for rk356x platform.
Driver support Gen3 by operating as a Root complex.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add a return value to pci_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Now that the sequence-numbering migration is complete, rename this member
back to seq_, adding an underscore to indicate it is internal to driver
model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This reverts commit 828d326216.
This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.
Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.
To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.
Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.
So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This function current deals with req_seq which is deprecated. Update it to
use the new sequence numbers, putting them above existing aliases. Rename
the function to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
