commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function")
implemented .enable, so fixed rate clocks can be used where drivers
might call clk_enable(). Implement the .disable op for the same reason;
some drivers, e.g. USB PHYs, may attempt to disable clocks at runtime.
Signed-off-by: Samuel Holland <samuel@sholland.org>
While we intentionally set -std=gnu11 for building host tools, and have
for quite some time, we never dropped -std=gnu99 from tools/Makefile.
This resulted in passing -std=gnu11 ... -std=gnu99 when building, and
gnu99 would win. This in turn would result now in warnings such as:
tools/mkeficapsule.c:25:15: warning: redefinition of typedef 'u32' is a C11 feature [-Wtypedef-redefinition]
typedef __u32 u32;
^
Signed-off-by: Tom Rini <trini@konsulko.com>
This enables the clock controller driver support on TI's SoCs. This will
fix this GPIO issue at boot time:
request_and_set_gpio: Unable to request GPIO_PR1_MII_CTRL
request_and_set_gpio: Unable to request GPIO_MUX_MII_CTRL
request_and_set_gpio: Unable to request GPIO_FET_SWITCH_CTRL
request_and_set_gpio: Unable to request GPIO_PHY_RESET
This issue comes from the fact that the clock controller is not probed.
Enable the TI's clock controller driver support to solve this.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
At present U-Boot always builds dtc if CONFIG_OF_CONTROL is defined, even
when DTC is provided. The built dtc is not actually used, so this is a
waste of time.
Update the Makefile logic to build dtc only if one is not provided to the
build with the DTC variable. Add documentation to explain this.
This saves about 3.5 seconds of elapsed time on a clean build of
sandbox_spl for me.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need this to make building dtc optional. It makes no sense to build our
own dtc if the system one works correctly.
This reverts commit ddb87a0b40.
Signed-off-by: Simon Glass <sjg@chromium.org>
Bulletproof the default boot command with reset statements in case
any command in the chain would fail. In case a failure were to happen,
the board will reset, increment boot counter and retry the procedure.
In case the failures persist and the boot counter reaches the bootlimit,
U-Boot starts altbootcmd instead of the default bootcmd boot command.
The altbootcmd swaps the default boot partition for the other boot
partition, which is an identical copy or an older copy, and tries
booting from that one instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Build U-Boot in Thumb2 mode for M53Menlo board, this makes better
use of the CPU since the instruction density is higher.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The board can do primary/secondary boot switching, enable the bmode command.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Move setting CONFIG_BOOTCOMMAND to the mx7ulp_com_defconfig file.
It also allows replacing the default CONFIG_BOOTCOMMAND without
code modification.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add redundant environment support as it is required
by SWUpdate.
While at it, place the CONFIG_ENV_OFFSET at 0x100000 to allow
more headroom.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The previous patches removed OF_PRIOR_STAGE from the last consumers of the
Kconfig option. Cleanup any references to it in documentation, code and
configuration options.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
So let's remove the option in an effort to simplify U-Boot's config and DTB
management, and use OF_BOARD instead.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
On RISC-V some of the boards pick up the DTB from a1 and copy it in their
private gd_t. Apart from that they copy it to prior_stage_fdt_address, if
the Kconfig option is selected, which is unnecessary.
So let's switch the config option for those boards to OF_BOARD and define
the required board_fdt_blob_setup() for them.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The default configuration of rk3399 EMMC PHY does not enable the
strobe line, and EMMC controller will got data transmission error
at HS400 mode.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fix up ppll init freq.
support tclk_emmc.
add freq (26M) for mmc device.
fix up the sfc clk rate unit error.
Change in V2:
remove change id.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using read_poll logic.
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set clock related processing into set_speed logic. And Optimize
printing format.
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The devicetree submitted and approved for the mainline linux kernel is
slightly different than the one present here. This syncs both
devicetrees (for the Rockchip SFC node at least) present on the PX30
and the Odroid Go Advance. Changes include renaming the flash node,
reordering the values in the SFC node for the rk3326-odroid-go2,
changing the name of the cs pinctrl node to cs0, and updating the
u-boot specific tree to utilize the new flash node value.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Brand names are supposed to be written with a capital,
so change them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the list of mainline U-boot supported Rockchip boards
rk3188 is placed below under the name rv3188. Give back it's
original name and sort the list in alphabetical order.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 64 bit rk33xx chips don't have the ROCKCHIP_USB2_PHY IP so
drop the configs as they were likely copied over from other
boards during enablement.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 would fail to probe for the
Odroid Go Advance. This patch is to remove the clock for the GPU from
the U-Boot specific devicetree, as that clock is not supported by the
U-Boot clk_px30 driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 for the Odroid Go Advance would
no longer probe correctly, because setting the cpll and gpu clocks are
not supported with the clk_px30 U-Boot driver. This adds support for
setting the cpll clock to the clk_px30 driver. Another patch will
update the U-Boot specific device-tree to remove the GPU clock which is
not used by U-Boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the latest reference of CONFIG_CONS_NONE in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_SYS_FLASH_AMD_CHECK_DQ7 in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the latest reference of CONFIG_NO_RELOCATION in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This define was left over from a previous revision, and was never used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.
for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...
cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\
Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Update the e-mail addresses and person responsible.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
CC: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
CC: Rainer Boschung <rainer.boschung@hitachienergy.com>
When a test hands on a real board there is no way on the console to obtain
any information about why it hung.
With sandbox we can actually find out that it died and get a signal or
exit code. Add this to make it easier to figure out what happened.
So instead of:
test/py/u_boot_spawn.py:171: in expect
c = os.read(self.fd, 1024).decode(errors='replace')
E OSError: [Errno 5] Input/output error
We get:
test/py/u_boot_spawn.py:171: in expect
c = os.read(self.fd, 1024).decode(errors='replace')
E ValueError: U-Boot exited with signal 11 (Signals.SIGSEGV)
Signed-off-by: Simon Glass <sjg@chromium.org>
Header type is 7-bit number so use all 7 bits when detecting header type
and not only 2 bits.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Header type is 7-bit number so properly clear upper 8th bit which
indicates multifunction device.
And do not try to show bars for unsupported header types.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Function dm_pci_hose_probe_bus() expects that bus is valid PCI device with
Bridge header type (0x01). So add check before touching PCI config space to
prevent misconfiguring some non-standard device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
